Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for PCE Health and Fitness PCE-186 CB
Summary of Contents for PCE Health and Fitness PCE-186 CB
- Page 1 User Manual PCE-186 CB Cable Detector User manuals in various languages (français, italiano, español, português, nederlands, türk, polski, русский, 中文) can be found by using our product search on: www.pce-instruments.com Last change: 2 December 2019 v1.0 © PCE Instruments...
-
Page 2: Table Of Contents
Contents Safety notes ................... 1 Specifications ..................2 Amplifier Probe ..................3 Features ........................... 3 Instructions ........................3 Maintenance ........................4 Tone Generator / DMM ................4 Tone Generator Features ....................4 Tone Generator Instructions ..................... 5 DMM Features ......................... 7 Instrument Layout ................. -
Page 3: Safety Notes
Safety notes Please read this manual carefully and completely before you use the device for the first time. The device may only be used by qualified personnel and repaired by PCE Instruments personnel. Damage or injuries caused by non-observance of the manual are excluded from our liability and not covered by our warranty. -
Page 4: Specifications
Specifications AC voltage measurement Measuring range Resolution Accuracies 400 mV 0.1 mV ± 1% + 5 Dgt 1 m V ± 1% + 5 Dgt 10 mV ± 1% + 5 Dgt 400V 100 mV ± 1% + 5 Dgt 750V ±... -
Page 5: Amplifier Probe
Amplifier Probe Figure 1 Figure 2 Features • The Amplifier Probe is designed to identify and trace wires or cables within a group without damaging the insulation. • Works with any Tone Generator to identify wires. • Volume control for increased sensitivity and adjustable to suit work environment. •... -
Page 6: Maintenance
• Depress the round on/off spring-loaded button on the amplifier probe. The volume control switch can be adjusted to suit the environment. Volume can be increased to overcome noise, or decreased to reduce interference. • Touch the tip of the amplifier probe to the insulation of each suspect conductor. •... -
Page 7: Tone Generator Instructions
Tone Generator Instructions All of the following tests can be performed by using the red and black test leads or the modular plug. NOTE: When using the modular test plug, the polarity test function applies to Lines 1 and 2. The continuity and tone functions ONLY apply to Line 1. •... - Page 8 • VERIFYING LINES (SWITCH TO "OFF" THEN "CONT") Dial the line to be verified. While the line is ringing, connect the RED lead to the RING SIDE of the line and the BLACK to the TIP. In the "OFF" position, the indicator lamp will flicker "RED and GREEN" when the test leads are connected to the subject pair.
-
Page 9: Dmm Features
DMM Features • 4000 counts LCD. • Full automatic measurement. Voltage measurement. Resistor measurement. • Range change function. • Select function. • Data Hold function. • Continuity check. • Diode measurement. • Low battery indication. • Input impedance: 10MΩ. • Safety Standard: EN 61010-1 CAT III 600V EN 61010-2-30... -
Page 10: Instrument Layout
Instrument Layout ⑤ Hold Button ① Function rotary switch ② LCD ⑥ COM Terminal ③ Select Button ⑦ "+" Terminal ④ Range Button Button Functions ① Function rotary switch The rotary switch selects the function. ② LCD 3999-count LCD with LOW BATTERY indication. ③... -
Page 11: Measurement
⑤ HOLD Button Press the HOLD button (HOLD annunciator turns on) makes the meter stop updating the LCD display. This mode can be nested in most of the special modes. Enabling HOLD function in automatic mode makes the meter switch to manual mode, but the full scale range remains the same. -
Page 12: Resistance Measurement
Black Resistance Measurement • Switch to OHM range and make sure there is no power in the circuit being measured. Insert the BLACK test lead to the COM and the RED test lead to the "+" terminal. • Connect the test leads to the circuit or device under test and get the reading directly from the LCD. -
Page 13: Continuity Check
Continuity Check • Continuity check shares the same configuration with 400.0 Ω manual resistance measurement mode, but with buzzer output to indicate continuity. The buzzer generates a 2 kHz sound whenever the digit number less than 25 Ω. • Because the cycle time of measurement is only 50 ms, the least significant digit will not display. -
Page 14: Diode Measurement
Diode Measurement • Diode measurement mode shares the same configuration with 4000 V manual voltage measurement mode. • If the test circuit is open or the voltage drop between the two ports of the device (diode) under test are larger than 2 V, the LCD will show "OL". •... - Page 15 Do not use abrasives or solvents. If the meter is not used for over 60 days, remove the battery for storage. © PCE Instruments...
-
Page 16: Warranty
Warranty You can read our warranty terms in our General Business Terms which you can find here: https://www.pce-instruments.com/english/terms. Disposal For the disposal of batteries in the EU, the 2006/66/EC directive of the European Parliament applies. Due to the contained pollutants, batteries must not be disposed of as household waste. They must be given to collection points designed for that purpose. - Page 17 PCE Instruments contact information Germany France Spain PCE Deutschland GmbH PCE Instruments France EURL PCE Ibérica S.L. Im Langel 4 23, rue de Strasbourg Calle Mayor, 53 D-59872 Meschede 67250 Soultz-Sous-Forets 02500 Tobarra (Albacete) Deutschland France España Tel.: +49 (0) 2903 976 99 0 Téléphone: +33 (0) 972 3537 17 Tel.