Logik L200IR17 - Steam Iron Manual

UNPACKING

Remove all items from the packaging. Retain the packaging. If you dispose of it please do so according to any local regulations. The following items are included:

• Steam Iron
• Filler Cup
• Instruction Manual

If items are missing or damaged, please contact Partmaster (UK only). Tel: 0344 800 3456 for assistance.

PRODUCT OVERVIEW

IRONING TEMPERATURES

Check the ironing instructions attached to the item (they are on a label showing a symbol of an iron). Always follow these ironing instructions. The indications on the iron's Temperature Dial and the table below will help you.

GARMENT LABEL	FABRIC TYPE	THERMOSTAT REGULATION
	Synthetic	Low Temperature
	Silk-wool	Medium Temperature
	Cotten-linen	High Temperature
	Fabric not to be ironed

If there are no ironing instructions but you know the fabric, then use the table above. The table is valid only for the actual materials and does not take into account any finish applied to the fabric. Textiles to which a finish has been applied (wrinkle relief, printed T shirts etc.) should be ironed at a lower temperature.

If the fabric contains mixed fibres, select the lowest ironing temperature of the composition, e.g. iron a 60% polyester / 40% cotton mix at the temperature indicated for polyester.

The iron heats up quicker than it cools down. Sort fabrics to be ironed into groups according to temperature: wool with wool, cotton with cotton, etc. Start by ironing articles requiring low temperature settings and progress to higher ones.

Do not iron garments that are dirty or stained. The iron's heat may set the stain.

Pure (100%) wool fabrics may be pressed with the iron set to a steam position and the garment protected by a dry cloth.

FIRST TIME USE

Inspect the iron carefully.

Check that the voltage marked on the rating matches your mains voltage. Remove any protective film from the soleplate. Polish the soleplate lightly with a clean soft cloth to remove any residues.

Place the iron on the ironing board or a flat rigid surface.

Maintaining the finish of the iron's soleplate is essential. Keep the soleplate smooth: do not scratch it on metal objects (e.g. the edge of the ironing board, buttons, zippers, etc.) as these may impair performance.

SWITCHING OFF THE IRON

To prevent water leakage, set to the far side of the Steam Control to prevent water leakage from the soleplate.

When switching off the iron, set the Steam Control to , also turn the Temperature Dial to 0 position, then unplug the iron from the mains socket.

FILLING THE IRON

Make sure the iron is unplugged from the mains socket and the Steam Control is at the position.

Open the Water Cap, tip the iron up slightly and fill it carefully with fresh water using the supplied filler cup.

If you live in a hard water area, it is advisable to use distilled or de-mineralised water. Avoid using water containing softeners, perfumes or additives.

Do not fill the iron above the max mark indicated on the side of the iron.

OPERATION

• Ensure the iron is unplugged and the Steam Control is at the position.
• Fill the iron with water as described above.
• Place the iron on its heel on the ironing board rest and connect the mains cable to the mains socket.
• The Temperature Indicator will illuminate.
• Select the correct temperature by turning the Temperature Dial.

Turn anticlockwise to increase and clockwise to reduce temperature.

• Some parts have been lightly greased and the iron might smoke slightly when switched on for the first time. After a short while, this will cease. We recommend passing the iron over a clean cotton cloth before using it for the first time. The Temperature Indicator will go off when the indicated setting reaches the correct temperature. The iron is now ready for use. During use the indicator will cycle on and off as the thermostat maintains the iron at the correct temperature setting.
• In between operations and when filling the iron always stand the iron on its heel. NEVER leave the iron face down.

STEAM IRONING

Steam ironing should be carried out at the highest settings on the Temperature Dial. Steam ironing at lower temperatures may cause water to leak from the soleplate.

The quantity of steam is regulated by the Steam Control. Move the Steam Control to a suitable position depending on the quantity of steam required and the ironing temperature.

The iron gives off steam continuously only if you hold the iron horizontally. You can stop the continuous steam by placing the iron in a vertical position or by moving the Steam Control to theposition.

SHOT OF STEAM BUTTON

This feature may be used during steam or dry ironing only when the iron is at the highest settings on the temperature dial.

Press the Shot of Steam button to release a powerful surge of steam. You may need to press the button a few times to prime the surge of steam.

Wait a few seconds for the steam to penetrate the fabric before pressing the button again.

Excessive use of this feature will cause the iron to cool, and the Temperature Indicator will illuminate.

If this happens, wait for the Temperature Indicator to go off before using this feature again.

You can use this feature for horizontal and vertical ironing.

SPRAY BUTTON

Press the Spray button to spray water on the material. It may be used for steam or dry ironing.

• To avoid staining, do not use the spray on silk or synthetics, and be very careful when you iron delicate fabrics.
• To operate the spray and steam shot functions, the water tank must be at least one-quarter full. If these features stop working, fill the water tank.

AFTER YOU HAVE FINISHED IRONING

When switching off the iron, set the Steam Control to , also turn the Temperature Dial to 0 position, then unplug the iron from the mains socket.

Stand the iron in the upright position and let the iron completely cool down.

When the iron is cool:
Open the Water Cap, invert the iron and pour away the excess water from the water tank. When pouring away the water, gently shake the iron to remove any loose particles from the tank.

CAUTION!

• In between ironing always stand the iron in the upright position. NEVER leave the iron face down.
  

SELF-CLEANING

The self-cleaning feature cleans the inside of the plate, removing impurities. We recommend using it every 10-15 days.

1. Plug the iron into the mains socket.
2. Set the highest settings on the Temperature Dial and Steam Control.
3. Unplug the iron once the Temperature Indicator goes off, the iron should be held over a bowl before pressing and holding the Self Clean button immediately. Water will drain out with impurities.
4. Release the Self Clean button. Slightly tilt the iron to drain water out.
5. Plug the iron into the mains socket again. Set the highest settings on the Temperature Dial and iron on a damp cloth to remove deposits on the soleplate.

ANTI-DRIP SYSTEM

This is designed to prevent water escaping from the soleplate when the iron is cold. During use, the anti drip system may click loudly, particularly when heating up or cooling down. This is perfectly normal and indicates that the system is functioning correctly.

ANTI-SCALE SYSTEM

The built-in anti-scale cartridge is designed to reduce the build-up of lime scale which occurs during steam ironing and will prolong the working life of your iron. The anti-scale cartridge will not completely stop the natural process of lime scale buildup so always empty the water after use and self-clean the iron regularly.

SPECIFICATIONS

Voltage Rating: 220-240V~ 50Hz

Power consumption: 1800-2200W

Specifications may change without prior notice.

Visit Partmaster.co.uk today for the easiest way to buy electrical spares and accessories. With over 1 million spares and accessories available we can deliver direct to your door the very next day. Visit www.partmaster.co.uk or call 0344 800 3456 (UK customers only). Calls charged at National Rate.

The symbol on the product or its packaging indicates that this product must not be disposed of with your other household waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the time of disposal will help conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment.

For more information about where you can drop off your waste for recycling, please contact your local authority, or where you purchased your product.

DSG Retail Ltd. (co. no. 504877)
1 Portal Way, London, W3 6RS, UK

EU Representative
DSG Retail Ireland Ltd (259460)
3rd Floor Office Suite,
Omni Park SC, Santry, Dublin 9, Republic of Ireland