Table of Contents
Advertisement
IS Series + SP Series Operating Manual
IS 2.8P & IS 3.8P
8 x 2-inch (IS 2.8P) and 8 x 3-inch (IS 3.8P) matched,
■
high power handling transducers with Neodymium
magnet structures and heat-resistant voice coils
Switchable 8 Ω / 32 Ω impedance allows up to eight
■
loudspeakers to be driven by a single amplifier
channel.
AquaControl™ and Protēa DSP presets for selected
■
Ashly power amplifiers and DSP processors (see page
6 for listing)
2-pole Euroblock connector, plus 2 x ¼-inch phone
■
jacks (IS 2.8P)
4-pole Euroblock connector, plus 2 x SpeakOn®
Connectors (IS-3.8P)
High-strength and light aluminum enclosure
■
Durable, chip-resistant polymer coating
■
Optional pole, tripod, and tilt or flush wall mounts
■
SP 12.1P
12-inch, high power handling (350 W) low-frequency
■
transducer with ferrite magnet structure
4-pole Euroblock terminal inputs
■
Neutrik® SpeakOn x 2 inputs
■
Internally-braced birch ply enclosure
■
Pole sockets on top and side
■
SP 8.1P
8-inch, high power handling (150 W)low-frequency
■
transducer with ferrite magnet structure
4-pole Euroblock terminal inputs
■
Neutrik SpeakOn x 2 inputs
■
Internally-braced birch ply enclosure
■
Pole sockets on top and side
■
10mm bolt holes for use with optional flying hardware
■
Thank you for choosing Ashly IS Series line
array column speakers (and hopefully our
matching subwoofer). We know that there are
many choices on the market today; so we have
worked hard to create column speakers that set
themselves apart from the rest.
Elevate or wall-mount a pair of IS 3.8P or IS
2.8P speakers on stands, add one or more
SP 8.1 P or SP 12.1P subwoofers and you have a
high-fidelity, high-output system that's perfect
for reception halls, small churches, mobile
discos, bars, coffee shops, and many other
applications.
Before installation, check for any possible
shipping damage. Also, please read all of the
Safety and Operation Precautions on the
previous page.
Note that this Guide also covers IS-TWM Tilt
Wall Mount Bracket, IS-JP Joining Bracket, and
Contents
Back Panel Connections ...................... 3
with Dual -impedance IS Series........... 4
Other Typical Configurations .............. 5
Basic Loudspeaker Processing ............ 7
IS 2.8P Specifications ....................... 11
SP 8.1P Specifications ...................... 16
SP 12.1P Specifications .................... 17
IS-FW Joining Bracket Install ............. 18
IS-TWM Tilt Bracket Install ................ 19
IS-PM6B Tripod ................................. 19
Other IS Accessories ........................ 19
IS-FWM Flush Wall Mount Bracket.
Back Panel Connections
IS Series columns are designed for both
permanent and mobile applications. Both
models have Neutrik® connections. The IS
3.8P adds Neutric SpeakOn connectors; the IS
2.8P has ¼-inch TS jacks.
IS 2.8P
¼-inch TS jack can be
used as the IS 2.8P
input or a pass-through
to another IS 2.8P
8 Ω / 32 Ω
impedance
switch
¼-inch TS jack can be
used as the IS 2.8P
input or a pass-through
to another IS 2.8P
2-conductor
Euroblock terminal
connector
*
WARNING:
When connecting the IS speaker,
do not under any circumstances
plug outputs
from different amplifiers or amp channels into
more than one jack (any type on the speaker) at
the same time.
*
IS
SERIES
3.8
LINEAR COLUMN LOUDSPEAKER
FREQUENCY RESPONSE:
100Hz - 20kHz
RATED POWER:
240W
8 /32
RATED IMPEDANCE:
MADE IN CHINA
8
32
INPUT
*
3
Advertisement
Table of Contents
