Page 1
Operating and Installation Manual IS 2.8P 8 x 2-inch column speakers IS 3.8P 8 x 3-inch column speakers SP 12.1P Twelve-inch subwoofer IS-TR7B Tripod mount for IS 2.8P or IS 3.8P IS-PM6B Pole mount for IS 2.8P or IS 3.8P + SP 12.1P IS-TWM Tilt wall mount for IS 2.8P or IS 3.8P...
Page 2
Don’t unplug signal cables when the amp Use only with mounts or brackets specified When using two IS speakers joined by an IS- connected to your IS Series speakers is still by Ashly Audio. JP2 vertical mounting plate, pay particular Check the suitability of the support surface attention to tripod placement.
IS Series + SP 12.1P Operating Manual Back Panel Connections Thank you for choosing Ashly IS Series line IS 2.8P & IS 3.8P array column speakers (and hopefully our IS Series columns are designed for both matching subwoofer). We know that there are permanent and mobile applications.
IS Series + SP 12.1P Operating Manual IS 3.8P SP 12.1P System configurations with Dual-impedance IS Series IS Series’ Hi-Z / Lo-Z design allows more connection options than typical single- 4-conductor – – impedance column speakers. Neutrik® SpeakOn Euroblock –...
Ashly Pow Each channel delivers power @ 4 – Bridge Required amplifier power = total number of cabinets x desired speaker wattage Ashly 2-ch. Power Amplifier If you need 60W per IS Series speaker, then 60 x 8 = 480 W...
Page 6
IS Series + SP 12.1P Operating Manual Ashly 2-ch. Power Amplifier Ashly 4-ch. Power Amplifier Amp running at 4 per channel 2 channels @ 8 , 2 -channels Bridge Mode (sub) NOTE: If amp power exceeds more than 2 x...
IS Series + SP 12.1P Operating Manual Ashly AquaControl (via Universal AquaControl™) crossover and Protēa™ software presets Directivity- implementation for IS Speakers weighted, for use between FIR-corrected, optimized linear subwoofers linear phase Basic Ashly frequency and full-range response above loudspeaker...
Page 8
IS Series + SP 12.1P Operating Manual Frequency IS 2.8P Specifications Response (On-Axis) Transducer 8 x 2-inch (51 mm)Neodymium Frequency Response 115 Hz – 20 kHz (–10dB limits Sensitivity (ref 2.83V) 88 dB 1, 2 Nominal Impedance 8 Ω / 32 Ω switchable...
Page 9
IS Series + SP 12.1P Operating Manual Impedance IS 2.8P Specifications Frequency [Hz] 8 ohm 32 ohm Beamwidth Frequency [Hz] Horizontal Vertical Directivity Index Frequency [Hz] Directivity...
Page 12
IS Series + SP 12.1P Operating Manual Frequency IS 3.8P Specifications Response (On-Axis) 8 x 3-inch (76 mm) Transducer Neodymium Frequency Response 105 Hz – 19 kHz (–10dB limits Sensitivity (ref 2.83V) 95 dB 1, 2 Nominal Impedance 8 Ω / 32 Ω switchable...
Page 13
IS Series + SP 12.1P Operating Manual Impedance IS 3.8P Specifications Frequency [Hz] 8 ohm 32 ohm Beamwidth Frequency [Hz] Horizontal Vertical Directivity Index Frequency [Hz] Directivity Index...
IS Series + SP 12.1P Operating Manual IS-JP2 Joining Bracket Install IS-FW Joining Bracket Install NOTE: When joining two IS Easy peasy. Easy peasy. Easy peasy. Use correct fasteners for Use correct fasteners for Use correct fasteners for speakers invert the upper the wall type.
IS Series + SP 12.1P Operating Manual IS-TWM Tilt Bracket Install NOTE: Use correct fasteners for the wall type. Align to a wall stud 15˚ tilt when possible. And remember to securely 90˚ attach the safety cable. swivel Other IS Accessories...
Page 19
847 Holt Road, Webster, NY USA US toll-free +1.585.872.0010 Fax +1.585.872.0739 Sales@Ashly.com www.Ashly.com Questions? Install problems? We think that Ashly Technical Support is the best in the pro audio business. Just call us (8 AM-5PM Eastern time zone) or e-mail us. US toll-free +1.585.872.0010...