CLT2435 ENG-5/28 5/28/01 13:46 Page i INSTRUCTION MANUAL CLT-2435 2.4-GHz Digital Spread Spectrum Cordless Telephone with Call Manager Features www.sanyocanada.com...
Page 2
CLT2435 ENG-5/28 5/28/01 Introduction Note: Some illustrations in this manual may differ from the actual unit for explanation purposes. Features 2.4-GHz Digital Spread Spectrum Technology 13:50 Page ii...
CLT2435 ENG-5/28 5/28/01 GETTING Setting up the base unit Notes: • The location should be close to both a phone jack and a continuous power outlet which is not switchable. • Be sure there is sufficient space to raise the base antenna fully to a vertical position. •...
Desktop use Connect the base unit To AC outlet AC adaptor (supplied) To telephone outlet Telephone line cord (supplied) Note: When connecting the power cord, make sure it does not create a trip or fire/electrical hazard. Avoid places where it could become chafed.
• Connect the AC adaptor to a continuous power supply. • Place the base unit close to the AC outlet so that you can unplug the AC adaptor easily. • If your telephone outlet is not modular, contact your telephone company for assistance. Choose the dialing mode...
CLT2435 ENG-5/28 5/28/01 GETTING Handset retainer Note: When the phone is mounted on the wall, the handset belt clip must be attached to hold the handset in the charging position. Do not place the handset with the display facing inside. Direct wall-mounting 1/8 in.
CLT2435 ENG-5/28 5/28/01 GETTING Preparing the battery pack CHARGE/IN USE 13:46 Page 9 STARTED Note: Use only the battery pack supplied or the specified Sanyo types with your phone. Type: SANYO 3KR-600AAL or SANYO/GE GES-PCF01 CHARGE/IN USE...
CLT2435 ENG-5/28 5/28/01 GETTING Battery use time (per charge) Note: While Voice Mail is displayed the battery discharges faster than in normal standby mode. To conserve the battery charge check your messages regularly to clear the display. (See page E39) When the battery charge level becomes low Cleaning the battery contacts Note:...
CLT2435 ENG-5/28 5/28/01 BASICS Making a call With the handset TALK/END SPEAKER Notes: • Press DELETE/SCAN if you enter a wrong number at step 1. • Press and hold DELETE/SCAN to delete all numbers at once. • You must press a key within 20 seconds or the phone will return to standby mode. 13:46 Page 11 Dialing from standby mode...
CLT2435 ENG-5/28 5/28/01 BASICS Redialing a call With the handset TALK/END Notes: • If the dialed number exceeds 32 digits, only the first 32 digits are retained for redialing. • If no number has been dialed, you hear an error tone and no redialing will be made. 13:46 Page 17 Redialing from standby mode...
CLT2435 ENG-5/28 5/28/01 BASICS With the base 13:46 Page 18 Redialing from talk mode TALK/END REDIAL/PAUSE TALK/END Notes: • Only the last number dialed can be accessed after TALK/END has been pressed. • If no number has been dialed using the handset, you hear an error tone and no redialing will be made.
CLT2435 ENG-5/28 5/28/01 13:46 Page 19 DIRECTORY/ SPEED-DIAL Using the handset directory Storing names/numbers MEMORY INTERCOM/SELECT DELETE/SCAN REDIAL/PAUSE TONE/ / Note: In memory store operation, you must press a key within 20 seconds or the phone will return to standby. If you return the handset to the base, it will return to standby, too.
Page 24
CLT2435 ENG-5/28 5/28/01 DIRECTORY/ INTERCOM/SELECT REDIAL/PAUSE Note: The pause feature is useful for long distance calling, credit card dialing, or sequences that require a pause between certain digits. DELETE/SCAN DELETE/SCAN INTERCOM/SELECT MEMORY 13:46 Page 20 SPEED-DIAL REDIAL/PAUSE...
Page 25
CLT2435 ENG-5/28 5/28/01 DIRECTORY/ Making calls from the handset directory REDIAL/PAUSE TONE/ / Notes: • If you press INTERCOM/SELECT before TALK/END, you can confirm the name and number stored in the selected memory location. • To exit the memory function without dialing, press MEMORY. The handset returns to standby.
CLT2435 ENG-5/28 5/28/01 DIRECTORY/ Using the base station speed-dial memory Storing numbers in the speed-dial memory Note: If you store a phone number in one of the speed-dial locations and attempt to store a different number in the same location later, the new number will replace the previous one.
Page 31
CLT2435 ENG-5/28 5/28/01 DIRECTORY/ Dialing a number from the speed-dial memory Erasing a number in the speed-dial memory 13:46 Page 27 SPEED-DIAL SPEAKER MEMORY MEMORY MEMORY SPEAKER CHARGE/IN USE...
CLT2435 ENG-5/28 5/28/01 CALLER ID Caller ID Note: You must subscribe to Caller ID on Call Waiting (Visual Call Waiting) if you want to see the name/number of the second caller while you are already on the phone. (See page E36.) Setting Caller ID options Note: When you subscribe to Caller ID service, you may not want to answer every incoming call...
Page 33
CLT2435 ENG-5/28 5/28/01 CALLER ID SERVICE MENU INTERCOM/SELECT INTERCOM/SELECT INTERCOM/SELECT INTERCOM/SELECT Note: CIDCW Settings • When you subscribe to Call Waiting or Visual Call Waiting service, select On. • When you subscribe to Call Waiting with Options service (Call Director), select Opt. Please see page E47 for more information.
• When the call is via a private branch exchange (PBX), the caller's phone number and name may not appear. • When the call is received via a telephone company that does not offer Caller ID service, the caller's phone number and name do not appear. (This includes international calls.) •...
Notes: • In Caller ID operation, if no key is pressed within 20 seconds, an error tone sounds and the telephone returns to the standby mode. Note: The phone numbers and names of the Caller ID list can be up to 15 characters each.
CLT2435 ENG-5/28 5/28/01 13:46 Page 32 CALLER ID FEATURES Deleting information from the Caller ID list Deleting a Caller ID entry CID/FLASH DELETE/SCAN INTERCOM/SELECT DELETE/SCAN Note: If you receive an incoming call, the deleting operation is cancelled.
CLT2435 ENG-5/28 5/28/01 13:46 Page 33 CALLER ID FEATURES Deleting all Caller ID names/numbers CID/FLASH DELETE/SCAN INTERCOM/SELECT DELETE/SCAN Note: If you receive an incoming call, the deleting operation is cancelled.
Calling a party from the Caller ID list Notes: • When a long distance number is selected, • You cannot make a call from the Caller ID list if your CLT-2435 is connected to private branch exchange (PBX). INTERCOM/SELECT 13:47...
Page 39
• You cannot store a Caller ID entry that includes no phone number. • If there is an incoming call or page during memory storing, the operation is cancelled and the telephone is set to receive the incoming call or page. INTERCOM/SELECT...
CLT2435 ENG-5/28 5/28/01 13:47 Page 36 CALLER ID FEATURES Using Caller ID on Call Waiting service CID/FLASH CID/FLASH Note: When you subscribe to Call Waiting with Options service and CIDCW is set to Opt. in the Caller ID setup menu, you can press the CID/FLASH key after receiving a call waiting signal and view a list of options for handling the new call.
SERVICE MENU Note: A subscription may be required and fees may apply for using each of the features listed below. Contact your local telephone company for more details or subscription. List of features Voice Mail* Access (page E38) Network Features (page E43)
CLT2435 ENG-5/28 5/28/01 ADVANCED CALLING Voice Mail access Programming your access number SERVICE MENU INTERCOM/SELECT INTERCOM/SELECT Note: You must subscribe to a voice mail service from your telephone company in order to use this feature. 13:47 Page 38 FEATURES...
CLT2435 ENG-5/28 5/28/01 ADVANCED CALLING Retrieving your voice mail messages with the 1/ TALK/END SERVICE/MENU with the SERVICE/MENU KEY TALK/END Resetting the message waiting indicator VOICE MAIL indicator INTERCOM/PAGE/FIND Key 13:47 Page 39 FEATURES VOICE MAIL Note: If no number has been dialed using the handset, you hear an error tone and the handset returns to standby.
CLT2435 ENG-5/28 5/28/01 ADVANCED CALLING Call transfer feature Transferring a call To transfer from the handset to the base To transfer from the base to the handset 13:47 Page 40 FEATURES INTERCOM/SELECT INTERCOM/PAGE/FIND INTERCOM/PAGE/FIND INTERCOM/SELECT SPEAKER TALK/END SPEAKER TALK/END SPEAKER TALK/END...
CLT2435 ENG-5/28 5/28/01 ADVANCED CALLING Intercom feature Using the intercom of your phone Paging from the base to handset Paging from the handset to base Note: • If the page is not answered within one minute, the paging stops automatically. •...
CLT2435 ENG-5/28 5/28/01 ADVANCED CALLING 3-way conference feature 3-way conference When a call is in progress on the handset When a call is in progress on the base 13:47 Page 42 FEATURES SPEAKER SPEAKER TALK/END TALK/END...
CLT2435 ENG-5/28 5/28/01 ADVANCED CALLING Accessing calling features Note: You must select a service from the menu before pressing TALK/END (or SPEAKER). Notes: • When using certain calling features, local toll or long distance charges may apply. • Certain calling features may not be used on some long distance calls or from certain types of business lines.
CLT2435 ENG-5/28 5/28/01 13:47 Page 45 ADVANCED CALLING FEATURES Adding new features Add or edit a service SERVICE MENU INTERCOM/SELECT INTERCOM/SELECT...
Page 50
CLT2435 ENG-5/28 5/28/01 13:47 Page 46 ADVANCED CALLING FEATURES INTERCOM/SELECT DELETE/SCAN DELETE/SCAN INTERCOM/SELECT DELETE/SCAN DELETE/SCAN INTERCOM/SELECT SERVICE MENU...
CLT2435 ENG-5/28 5/28/01 ADVANCED CALLING Call Waiting with Options Setting CIDCW option Selecting an option 13:47 Page 47 FEATURES SERVICE MENU INTERCOM/SELECT INTERCOM/SELECT CID/FLASH INTERCOM/SELECT...
CLT2435 ENG-5/28 5/28/01 13:47 Page 48 ADDITIONAL INFORMATION CID/FLASH Changing the digital security code INTERCOM/PAGE/FIND INTERCOM/PAGE/FIND Note: If the handset battery pack is completely discharged or the battery pack is removed, the digital security code will be lost. If this happens, a new security code is set automatically the next time the battery pack is charged.
CLT2435 ENG-5/28 5/28/01 ADDITIONAL Installing the belt clip To attach the belt clip Note: If you have wall-mounted the base, you must install the belt clip to hold the handset in the proper charging position. Do not hang the handset with the display facing inside.
Page 60
CLT2435 ENG-5/28 5/28/01 13:47 Page 56 Covered under one or more of the following U.S. patents: SANYO All rights reserved UCZZ01750GZ Printed in China...