Page 1
Wood Chipper Instruction Manual WARNING: Read carefully and understand all INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in serious personal injury. Save these instructions in a safe place and on hand so that they can be read when required. Keep these instructions to assist in future servicing.
Page 2
WARNING SYMBOL WARNING: This is the warning symbol to get your high attention for the instruction notice, which should be followed to avoid the potential serious personal injury. Anyone to use this equipment should read all the instructions of this manual. Keep this instruction manual for future reference.
GENERAL OPERATING SAFETY 1.Read, understand, and follow all instructions in the manual and on the unit before starting. 2. Locate the Chipper/Shredder on a flat, level, sturdy surface capable of supporting the weight of the Chipper / Shredder and any additional tools and equipment. 3.
Page 5
8. Never attempt to reposition or move the chipper shredder unit while it is running. Doing so could cause the machine to tip over, and reaching to steady the unit could result in accidental insertion of your hands into the chipper cone or shredder hopper areas.
Page 6
Gasoline Fires and Handling Fuel Safely Use extra care in handling gasoline and other fuels. They are flammable and vapors are explosive. 1. When storing extra fuel be sure that it is in an appropriate container and away from any fire hazards. 2.
ASSEMBLY Install Stand (See Figure 1) 1. Position the stand (A) underneath the engine base 2. Using the four M8x60 bolts (B) and four nuts (D) with 8 flat washer(C)to tight the stand with the engine base plate. 3. Fix the wheel bracket (E) on the housing with three M8x20 bolts (G) and three M8 nuts.(F) Figure 1 Install the Wheels (See Figure 2) 1.
Page 8
In-feed bin installation (see Figure 3) 1. Place the Infeed bin (A) on four M8 bolts; 2. Fix the bolt with four M8 flange nuts (B). Figure 3 Fixed the discharge chute (see Figure 4) 1. Place the discharge chute (A) on the housing and align the fixed hole. Fix the discharge chute with three M8*16 bolts (B) on the housing.
Fixed the discharge chute guide (see Fig. 5) 1. The guide (A) is placed at the fixed holes of the discharge chute 2 .Fix the discharge chute guide with 2 M6*12 (D), 2 elastic washers (C), 1 flat washer (B) and 1 M6*16 star handle Figure 5 GENERAL OPERATION 1.
WARNING 1. GASOLINE IS HIGHLY FLAMMABLE AND MUST BE HANDLED WITH CARE. NEVER FILL THE TANK WHEN THE ENGINE IS STILL HOT FROM RECENT OPERATION. 2. DO NOT ALLOW OPEN FLAME, SMOKING OR MATCHES IN THE AREA. AVOID OVER-FILLING AND WIPE UP ANY SPILLS.
MAINTENANCE Schedule & Procedures The following schedule should be followed for normal care of your unit. BEFORE EVERY EVERY EVERY EVERY SPRING SAFETY ITEMS EACH USE 5 HOURS 25 HOURS 100 HOURS 250 HOURS & FALL Check for loose hardware Check all safety labels Inspect cone, hopper, and guards CHIPPER MAINTENANCE ITEMS...
CAUTION 1. FOR THE SAFETY OF THE USER, AND TO MAXIMIZE THE LIFE OF THE ENGINE, IT IS CRUCIAL TO TAKE TIME TO CHECK THE CONDITION OF THE ENGINE. 2. PROBLEMS MUST BE CORRECTED BEFORE OPERATING. 3. AVOID INJURY! ENGINE OIL IS HAZARDOUS TO YOUR HEALTH. DISPOSE OF OIL APPROPRIATELY. 4.
Chipping Knives Sharpening and Replacement 1. The chipping knives should be sharpened or replaced when tree limbs require extra force to feed into the chipper cone. 2. The chipping knives may be sharpened at a 39 degree angle until the distance between the edge of the blade bevel and the mounting hole is less than 1/16”...
Need help?
Do you have a question about the LCE12 and is the answer not in the manual?
Questions and answers