Subscribe to Our Youtube Channel
Related Manuals for Outdoor GreatRoom Company SONOMA12-R
Summary of Contents for Outdoor GreatRoom Company SONOMA12-R
- Page 1 Sonoma 12 Pergola Manual and Installation Instructions Please read these instructions before removing parts from crate. outdoorrooms.com...
-
Page 2: Required Tools
Thank you for your purchase from The Outdoor GreatRoom Company. This pergola has been engineered and manufactured in the USA. This user manual will help make the installation and setup of your new pergola fast and easy. Outdoor GreatRoom company recommends visiting with your local authority for building codes, restrictions, or requirements for this product. - Page 3 INCLUDED PARTS (WOOD) HEADER BEAM X4 COLUMN X4 HEADER BEAM X4 TALL CORBEL POST BRACE X4 HEADER BEAM X2 SHORT CORBEL POST BRACE X4 CANOPY BEAM X10 ARCH BEAM X8 SONOMA 12 LATTICE (OPTIONAL) 90224 REV F 01-08-19 outdoorrooms.com...
- Page 4 INCLUDED PARTS (METAL HARDWARE) - M10 X 55 HEX BOLT (with nut and washers) - RECTANGULAR MENDING PLATE X10 - M10 X 160 HEX BOLT (with nut and washers) - ARCH MENDING PLATE X8 - M10 X 90 HEX BOLT (with nut and washers) - FOOT X4 OPTIONAL HARDWARE KIT - 1.25”...
- Page 5 PERGOLA ASSEMBLY STEP 1 STEP 2 Bolt steel footplate to each of four supplied posts Apply construction adhesive to boards on one “A” as shown. Use hardware “M” and “O” side and bolt beams together as shown using bolts “P” with a nut and washer. Bolt heads should be on the side comprise of beams “E”...
- Page 6 STEP 3 STEP 4 Attach rectangualr mending plate “K” to canopy With arch beams “J” laying flat on ground, bolt beams as shown below. Attach beams “G” together together (4X) using supplied hardware bolts “N”, (5X). and mending plates “L” 90224 REV F 01-08-19 outdoorrooms.com...
- Page 7 ATTENTION In the remaining steps, a rubber mallet may be useful in fitting beams together properly. STEP 5 STEP 6 Lay columns on level surface. Bolt ledger beams Attach short corbels “C” with hardware assembled in step 2 to column “A” with beams screws “R”...
- Page 8 STEP 8 STEP 7 Once header beams are installed and bolts are Carefully position posts in final location. Check tightened, end arch beam sections can be in- for square. Install canopy beam assemblies with screw “R” at intersections with arch beams. The stalled between them and secured in place with use of a level or similar tool is highly suggested.
- Page 9 DIMENSIONAL AND POST LOCATION INFORMATION ATTENTION ATTENTION Do not do final tightening of all bolts until Recommended 12-18” diameter footing unit is fully assembled, level and square. (12” minimum). After pergola is IN POSITION, SQUARED Check local codes for depth minimums. UP, and LEVELED, anchor posts with Footing typically is 24”...
- Page 10 LATTICE INSTALLATION (OPTIONAL) STEP 1 STEP 3 Carefully lower lattice “W” into opening. Mount brackets “T” and “U” to “G” as shown Make sure lattice is placed securely on below using (2X) “V” screws. each bracket. Position brackets 2in. from ends. 2in.
- Page 11 The Outdoor GreatRoom Company extends the following warranty for Outdoor GreatRoom outdoor products used in the United States of America or Canada. Dealers and employees of The Outdoor GreatRoom Company have no authority to make any warranty or authorize any remedies in addition to or inconsistent with the terms of this warranty.
Need help?
Do you have a question about the SONOMA12-R and is the answer not in the manual?
Questions and answers