1. Manuals
  2. Brands
  3. Fuel Fitness Manuals
  4. Exercise Bike
  5. SU135-40
  6. Owner's manual

Fuel Fitness SU135-40 Owner's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
SU135-40 UPRIGHT
OWNER'S MANUAL
PLEASE CAREFULLY READ THIS ENTIRE MANUAL BEFORE
OPERATING YOUR UPRIGHT!

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SU135-40 and is the answer not in the manual?

Questions and answers

Related Manuals for Fuel Fitness SU135-40

Summary of Contents for Fuel Fitness SU135-40

  • Page 1 SU135-40 UPRIGHT OWNER’S MANUAL PLEASE CAREFULLY READ THIS ENTIRE MANUAL BEFORE OPERATING YOUR UPRIGHT!

  • Page 2: Safety Hints

    Wear proper shoes. High heels, dress shoes, sandals or bare feet are not suitable ■ for use on your upright. Quality athletic shoes are recommended to avoid leg fatigue. SAVE THESE INSTRUCTIONS - THINK SAFETY! CAUTION!! Please be careful when un-packing the carton. SU135-40- TB001_ 1207A...

  • Page 3: Assembly Pack Check List

    Assembly Pack Check List STEP 1. #33- 5/16" Flat #34- 5/16" Curved Washer (8pcs) Washer (1pc) #35- 5/16"X1.5T Split #32- 5/16" × 3/4" Button Washer (4pcs) Head Socket Bolt (9pcs) STEP 2. #41- M5 × 12 mm Phillips Head Screw (4pcs) #72- 3/8”...
  • Page 4 Assembly Instructions STEP 1: 1. Locate the Console Mast (2) and slide on the Console Mast Cover (60). Make sure the cover is facing the correct direction, as shown below, before sliding onto mast. Install the wiring harness (80) into the bottom of the mast and out the top. Be careful when installing the console mast to the mainframe so as not to pinch or cut the wiring harness, damage to the console may occur.
  • Page 5 STEP 2: 1. Install Handle Bar (3) on Console Mast (2) and lock with Quick Release lever (19). Install the Hand Pulse Cable (82) through the console mounting plate as shown below. 2. Connect Computer Cable (80) and Hand Pulse Sensor Cable (82) to the Console (48) and assemble on the Console Mast (2) using Phillips Head Screw Driver (43) to tighten 4pcs of M5 ×...

  • Page 6: Key Functions

    Console Key Functions START/STOP: 1. Starts & Pauses workouts. 2. Starts body fat measurement. 3. Holding key for 3 seconds will reset all functions and values to zero. DOWN: Decreases value of selected workout parameter: TIME, DISTANCE, etc. During the workout it will decrease the resistance load.

  • Page 7: Workout Parameters

    Functions: SPEED: Displays current training speed. Maximum speed is 99.9 KM/H or MILE/H. RPM: Displays current pedal rotations per minute. TIME: Accumulates workout time from 00:00 to 99:59. Or users can preset the target time desired. DIST: Accumulates the workout distance form 0.00 up to 999.9 KM or Mile. Or users can preset the target distance they want to reach.

  • Page 8: Program Operation

    More About Workout Parameters Setting Default Increment/ Parameter Description Range Value Decrement 1. When display is 0:00, Time will count Time 0:00~ 99:00 00:00 ± 1:00 2. When time is 1:00-99:00, It will count down to 0. 1.When display is 0.0, Distance Distance will count up.
  • Page 9 Pre-programs (P2~P13) Program profile ROLLING VALLEY FAT BURN RAMP STEPS OBSTACLE INTERVALS PLATEAU CLIMBING OFF ROAD HILL FASTREK...
  • Page 10 There are 12 pre-set program profiles ready for use ： ： ： ： R OLLING, VALLEY, FAT BURN, RAMP, STEPS, OBSTACLE, INTERVALS, PLATEAU, CLIMBING, OFF ROAD, HILL, FASTREK. All program profiles have 24 levels of resistance. Setting Parameters for Pre-set programs Select one of pre-set programs using UP OR DOWN KEY then pressing ENTER KEY.
  • Page 11 BODY FAT MEASUREMENT Setting Data for Body Fat Select “BODY FAT” using UP OR DOWN KEY then pressing ENTER. “Male” will flash indicating the Gender can be adjusted using UP OR DOWN KEY. Press ENTER to save gender setting & move to next setting. A Height of “175”...
  • Page 12 Note: If your Pulse measurement is above or below (± 5) the TARGET H.R setting, the computer will adjust the resistance load automatically; it will check approximately every 10 seconds. If the heart rate signal disappears, the computer will keep the resistance load constant for 60 seconds then it will decrease the resistance load 1 level every 10s.
  • Page 13 HEART RATE CONTROL Program Program profile There are 4 selection for target pulse: HRC- 55% TARGET H.R= 55% of (220-AGE) HRC - 65% TARGET H.R= 65% of (220-AGE) HRC - 75% TARGET H.R= 75% of (220-AGE) HRC - 85% TARGET H.R= 85% of (220-AGE) Setting Parameters for HEART RATE CONTROL Select one of the “Heart Rate Control Program”...
  • Page 14 User Program Program profile 4 User programs allow the user to create their own personal program. Setting Parameters for User Program Select “User” using UP OR DOWN KEY then press ENTER KEY. The 1 parameter, “Time” will flash indicating the value can be adjusted using UP OR DOWN KEY. Press ENTER KEY to save value &...

Table of Contents