1. Manuals
  2. Brands
  3. National Manuals
  4. Electric Shaver
  5. ES8093-A3
  6. Service manual

National ES8093-A3 Service Manual

Wet/dry rechargeable shaver
Hide thumbs

Advertisement

Table of Contents

SPECIFICATIONS
Power source
Power consumption
Motor voltage
Charging time
Shaves per charge
Measurement
Weight
Supplied accessories
CONTENTS
Wet/Dry Rechargeable Shaver
ES8093-A3
AC 100-240V, 50-60Hz (Automatic voltage conversion)
7W
24V DC
1 Hour
14 times (3 minutes shave)
(H)14 x (W)5.9 x (D)5.0 cm
230g
Semi hard case
Cleaning brush
Page
2
2
3
5
© 2003 Matsushita Electric Works, Ltd. All rights
reserved. Unauthorized copying and distribution is a
violation of law.
ORDER NO. SD0304A35C3
Page
7
10
10

Advertisement

Table of Contents
loading

Related Manuals for National ES8093-A3

Summary of Contents for National ES8093-A3

  • Page 1: Table Of Contents

    ORDER NO. SD0304A35C3 Wet/Dry Rechargeable Shaver ES8093-A3 SPECIFICATIONS Power source AC 100-240V, 50-60Hz (Automatic voltage conversion) Power consumption Motor voltage 24V DC Charging time 1 Hour Shaves per charge 14 times (3 minutes shave) Measurement (H)14 x (W)5.9 x (D)5.0 cm...

  • Page 2: Schematic Diagram

    ES8093-A3 1 SCHEMATIC DIAGRAM 2 WIRING CONNECTION DIAGRAM...

  • Page 3: Disassembly Instructions

    ES8093-A3 3 DISASSEMBLY INSTRUCTIONS Follow the procedure below to disassemble the main unit. 1. Remove the cap, the outer foil with foil frame and the 4. Remove the back panel and loosen a screw. inner blade. 2. Set the trimmer at about 19mm sliding above. To 5.
  • Page 4 ES8093-A3 7. Move gently the linear motor assembly down and 10. Take out the batteries from the chassis. unhook it from the housing A. Remove the lead wire tube from the housing A. 11. Unsolder the lead wires from the module.

  • Page 5: Caution In Assembly

    ES8093-A3 4 CAUTION IN ASSEMBLY NOTE: When reassembling, replace the new waterproof rubber. Make sure whether there is NO foreign substance sticking around a part covered with waterproof seal. 1. Attach the right and left side of the float guides.
  • Page 6 ES8093-A3 7. Attach the right and left sides of float suspension with care 10. Set the position where removing it and click hooked. of its own direction. If the position is not properly, it makes the deformation of the hook.

  • Page 7: Troubleshooting Guide

    ES8093-A3 5 TROUBLESHOOTING GUIDE (Refer to WIRING CONNECTION DIAGRAM) <TROUBLE> <CHECK.> <REMEDY> Motor does not rotate. <CHECK CHARGING ADAPTOR.> NO Replace charging → → → → Connect the rated voltage to the normal main unit setting onto the adaptor. → → → → adaptor.
  • Page 8 ES8093-A3 <TROUBLE> <CHECK.> <REMEDY> Noise is too loud. → Check if there any deformation with the outer foil. NO Replace the outer foil or Amplitude is too large. → → → → oiling a drop for the foil. ↓ ↓ ↓ ↓ OK <CHECK DRIVING BARS.>...
  • Page 9 ES8093-A3 <TROUBLE> <CHECK.> <REMEDY> Does not move pivot <CHECK FLOAT SUSPENSION.> NO Repair float suspensions → Confirm if the float suspensions assemble firmly. → → → → or clean. action selector or does not float the head Confirm if the beard chips collect around the linear motor assembly.

  • Page 10: Exploded View

    ES8093-A3 6 EXPLODED VIEW 7 REPLACEMENT PARTS LIST NOTE: *A=available as an optional accessory *B=only available as set *C=available individually Ref. No. Part No. Part Name & Description Remarks Per Unit WES8093X7159 PROTECTIVE CAP WES9093E SYSTEM OUTER FOIL WES9064E INNER BLADE...

Table of Contents