Related Manuals for Efco DS 220 TR
Summary of Contents for Efco DS 220 TR
- Page 1 Model not available for EU markets DS 220 TR (21.7 cm OPERATOR’S INSTRUCTION BOOK...
-
Page 5: Table Of Contents
TRANSLATION OF ORIGINAL INSTRUCTIONS 9. M A I N T E N A N C E ( a l l i n fo r m a t i o n required to keep the machine at peak efficiency) INTRODUCTION 10. STORAGE For correct use of the machine and to avoid 11. - Page 6 in good conditions. In case of damage or WARNING: National regulations may limit deterioration, immediately substitute them the use of the machine. (Fig. 18). 15 - Do not utilize the machine for uses 1 - Do not operate the machine unless you different from the ones specified in the have received specific instruction on its use.
-
Page 7: Symbols And Safety Warnings
2. SYMBOLS AND SAFETY WARNINGS (Fig.25) FITTING THE SAFETY GUARD (Fig. 8) 1 - Read operator’s instruction book before Fit the blade guard (A) to the shaft arm with operating this machine. screws (B) in a position allowing the operator to 2 - Wear head, eye and ear protection. - Page 8 The correct oil / fuel proportions shown in the H jet regulation to avoid critical issues. For table (Fig. A) are suitable when using the Efco this operation it’s necessary turned at a PROSINT 2 and EUROSINT 2 or an equivalent Licensed Service Dealer.
- Page 9 Left-handers should follow these instructions if engine is cold. too. Keep a proper cutting stance. - Now start the engine. Over exposure to vibrations can result in START-UP PROCEDURE blood-vessel or nerve injury to persons 1) Slowly push the purge bulb 6 times (9, Fig.1). suffering with blood circulation problems.
-
Page 10: Stopping The Engine
BREAKING-IN THE ENGINE prevent being pulled off balance. • Make sure you can move and stand safely. The engine reaches the maximum power after the Check the area around you for possible first 5÷8 hours of activity. obstacles (roots, rocks, branches, ditches, etc.) in case you have to move suddenly. - Page 11 your capability. You must understand the could get burnt if you touch it. difference between forestry clearing, grass clearing and grass trimming before use. WARNING: Sometimes branches or grass get caught between the guard and Basic safety rules cutting attachment. Always stop the engine before cleaning.
-
Page 12: Transporting
CAUTION: This technique increases the wear on the cord. • The cord wears quicker and must be fed forward more often when working against stones, brick, concrete, metal fences, etc., than when coming into contact with trees and wooden fences. •... - Page 13 9. MAINTENANCE Maintenance Chart Please note that the following maintenance intervals apply for normal operating conditions only. If your daily work requires longer than normal or harsh cutting conditions are present, then the suggested intervals should be shortened accordingly. Inspect (Leaks, Cracks, and Wear) Complete Machine Clean after finishing daily work Controls (STOP button, Choke Lever, Throttle...
- Page 14 NYLON LINE HEAD SPARK PLUG Only use line of the same diameter as the original to avoid overloading the engine (Fig. 18). Clean spark plug and check electrode distance In order to get more line out of the cutting head, periodically (Fig.
-
Page 15: Storage
network at the end of season, if used surrounding area. - Scrupulously comply with local regulations intensively, and every two years if with normal and provisions for the disposal of waste use. materials after mowing. - Scrupulously comply with local regulations ATTENTION: All maintenance operations and provisions for the disposal of oils, petrol, not reported in this manual must be carried... -
Page 16: Technical Data (A Summary Of The Main Specifications Of The Machine)
12. TECHNICAL DATA DS 220 TR Displacement 21.7 Engine 2 stroke EMAK Power 3000 Min. rpm Maximum speed of output 8.200 spindle Engine speed at maximum 8.200 output spindle speed Fuel tank capacity 400 (0.40 l) Primer carburetor Antivibration system... - Page 17 NOTE:...
-
Page 18: Declaration Of Conformity
Guaranteed sound power level: 112.0 dB (A) 2. Brand Efco, Type DS 220 TR Technical Documentation deposited with Administrative 3. Serial ID 930 XXX 0001 ÷ 930 XXX 9999 (DS 220 TR) Headquarters: Technical Department conforms to the requirements of Directives:... -
Page 19: Troubleshooting (Helps You To Quickly Solve Any Problems You May En- Counter While Using The Machine)
15. TROUBLESHOOTING WARNING: Always stop unit and disconnect spark plug before performing all of the recommended remedies below except remedies that require operation of the unit. When all the possible causes have been checked and the problem is not resolved, consult an Authorised Service Centre. - Page 20 WARNING! – This owner’s manual must stay with the machine for all its life. Efco it’s an EMAK S.p.A. trademark 42011 Bagnolo in Piano (RE) Italy Tel. +39 0522 956611 • Fax +39 0522 951555 service@emak.it • www.efco.it...