Advertisement
PREPARING THE LAUNDRY
1. Check that all fastenings are closed and
that pockets are empty.
2. Turn the articles inside out.
3. Place laundry loosely in the drum to
make sure it doesn't become tangled.
Sort laundry as follows:
A) By care symbols
(on the collar or inside seam):
Suitable for tumble drying
Tumble drying with reduced
drying intensity only. Press
gentle button or select specific
programme
Do not tumble dry
B) By amount and thickness/weight
Whenever the load to be dried exceeds
dryer capacity, separate laundry
according to weight (e.g. towels from
thin underwear).
C) By type of fabrics
Cotton/linen: towels, cotton jersey,
bed and table linen made of cotton or
linen.
Synthetics/Easy Care: blouses, shirts,
overalls, etc. made of polyester or
polyamide, as well as cotton/synthetic
mixes.
D) By drying level
• Sort into: iron dry, cupboard dry, etc.
Do not tumble dry: woollens, silk, nylon
stockings, delicate embroidery, fabrics
with metallic decorations, bulky items such
as sleeping bags, etc.
Important: only use specific indicated
dryer-safe additives and rinse items
that have been treated with stain remover
thoroughly in plenty of water before
drying. Only use specific indicated
dryer-safe plastic items and never dry
rubber or articles contaminated with
vegetable oil in the dryer.
SELECTING A PROGRAMME & OPTIONS
Programme and Options:
•
To select a programme, turn the
programme selector knob. The Start/
Pause indicator lamp is blinking,
indicating that the cycle needs to be
started.
•
To select an option, press the
corresponding button. The indicator
lamp above the button confirms that a
selection has been made.
Press the button again to cancel the
•
option
.
STARTING & COMPLETING A
PROGRAMME
1. Having selected the desired
programme and options, press the
Start button.
If the laundry is not removed at the
end of the drying cycle, an automatic
anti-crease cycle will operate for
maximum 60 min. The drum rotates at
regular intervals, preventing the
laundry from creasing.
Anti-Crease protection re-
distributes laundry in the drum.
When the Anti-Crease option is
selected and laundry has not been
taken out, an anti-crease cycle is
activated for 12 hrs.
On completion of the programme, set
2.
the programme selector knob to
position "0"
.
CHANGING A PROGRAMME
When changing the programme during
the drying cycle, the dryer stops. The Start/
Pause indicator lamp is blinking.
To operate the new programme, press the
Start/Pause button again.
INTERRUPTING A PROGRAMME
To interrupt the dryer during
operation
1. Set the programme selector knob to
Airing.
2. Press the Start button.
Wait at least 5 minutes before opening
the door to allow the dryer to cool
down.
For your safety the programme stops
automatically if you open the door.
3.
To restart, after door opening, close
the door and press the Start/Pause
button again
.
DAILY MAINTENANCE & CLEANING
Clean the lint filter at the end of every
drying cycle:
1. Open the door.
2. Pull the filter upwards.
3. Remove lint using a soft brush or your
fingertips.
4.
Push the filter back into place.
TROUBLESHOOTING GUIDE
If a fault occurs, before contacting our
After-Sales Service, make the following
checks to try and remedy the problem:
Drying takes too long / laundry is not
dry enough:
•
Was the correct programme selected?
•
Was the inserted laundry too wet
(Washing machine spin speed less than
800 rpm)?
•
Is the lint filter dirty (filter indicator
lamp on)?
The dryer does not operate:
(after a power failure and/or
interruption to the mains supply,
always press the Start button).
•
Is the plug properly inserted into the
mains electricity socket?
•
Is there a power failure?
•
Has the fuse blown?
•
Is the door well closed?
•
Has the programme been selected?
•
Are the END and Anti-crease indicator
lamps lighting up? The drying cycle is
complete and the laundry can be taken
out.
•
Has the Start/Pause button been
pressed?
Lint filter indicator lamp on:
•
Is the lint filter clean?
•
Is the vent hose blocked?
All programme sequence indicators
blinking:
Service call necessary
•
.
AFTER-SALES SERVICE
If, after carrying out the above checks the
malfunction persists or appears again, turn
the dryer off and call our After-Sales
Service (refer to guarantee).
Please specify:
•
The nature of the fault.
•
The dryer type and model.
•
The service code (the number after the
word Service on the adhesive rating
plate) on the right-hand side when the
door is open.
Your full address and phone number
•
5019 407 00493
.
Advertisement
