Table of Contents
Advertisement
Quick Links
Digital Camera/Lens Kit/Double Zoom Lens Kit/Body
DMC-G3KPP
Model No.
DMC-G3KPC
DMC-G3KEB
DMC-G3KEC
DMC-G3KEE
DMC-G3KEG
DMC-G3KGC
DMC-G3KGD
DMC-G3KGH
DMC-G3KGK
DMC-G3KGN
DMC-G3KGT
DMC-G3PP
DMC-G3PC
DMC-G3EB
DMC-G3EC
DMC-G3EE
DMC-G3EG
DMC-G3GC
DMC-G3GD
DMC-G3GH
DMC-G3GN
© Panasonic Corporation 2011 Unauthorized copy-
ing and distribution is a violation of law.
ORDER NO. DSC1106032CE
B26
Advertisement
Chapters
Table of Contents
Related Manuals for Panasonic Lumix DMC-G3KPP
Summary of Contents for Panasonic Lumix DMC-G3KPP
- Page 1 Digital Camera/Lens Kit/Double Zoom Lens Kit/Body DMC-G3KPP Model No. DMC-G3KPC DMC-G3KEB DMC-G3KEC DMC-G3KEE DMC-G3KEG DMC-G3KGC DMC-G3KGD DMC-G3KGH DMC-G3KGK DMC-G3KGN DMC-G3KGT DMC-G3PP DMC-G3PC DMC-G3EB DMC-G3EC DMC-G3EE DMC-G3EG DMC-G3GC DMC-G3GD DMC-G3GH DMC-G3GN © Panasonic Corporation 2011 Unauthorized copy- ing and distribution is a violation of law.
-
Page 2: Table Of Contents
DMC-G3GT DMC-G3WGC DMC-G3WGD DMC-G3WPP DMC-G3WGH DMC-G3WEB DMC-G3WGK DMC-G3WEC DMC-G3WGN DMC-G3WEE DMC-G3WGT DMC-G3WEG Vol. 1 Colour [DMC-G3K] [DMC-G3W] (K)...Black Type (K)...Black Type (R)...Red Type (except GD/GT) (R)...Red Type (except PP/EE/GD/GT) (W)..White Type (except PC/EG) (W)..White Type (except PP/EB/EE/EG) (T)...Brown Type (only PP/EG/GC) (T)...Brown Type (only EG/GC) (KA)..Black Type (only EB) [DMC-G3]... -
Page 3: Safety Precautions
1 Safety Precautions 1.1. General Guidelines 1.3. Leakage Current Hot Check 1. IMPORTANT SAFETY NOTICE (See Figure 1.) There are special components used in this equipment 1. Plug the AC cord directly into the AC outlet. Do not use which are important for safety. These parts are marked by an isolation transformer for this check. -
Page 4: How To Discharge The E. Capacitor On Flash P.c
1.4. How to Discharge the E. Capacitor on Flash P.C.B. CAUTION: 1. Be sure to discharge the E. Capacitor on FLASH P.C.B.. 2. Be careful of the high voltage circuit on FLASH P.C.B. when servicing. [Discharging Procedure] 1. Refer to the disassemble procedure and remove the necessary parts/unit. 2. -
Page 5: Warning
2 Warning 2.1. Prevention of Electrostatic Discharge (ESD) to Electrostatically Sensitive (ES) Devices Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Elec- trostatically Sensitive (ES) Devices. The following techniques should be used to help reduce the incidence of component damage caused by electrostatic discharge (ESD). -
Page 6: Caution For Ac Cord (For Eb/Gc
A replacement fuse cover can be purchased from your local 2.3.2.3. How to Replace the Fuse Panasonic Dealer. 1. Remove the Fuse Cover with a screwdriver. If the fitted moulded plug is unsuitable for the socket outlet in your home then the fuse should be removed and the plug cut off and disposed of safety. -
Page 7: How To Replace The Lithium Battery
NOTE: This Lithium battery is a critical component. (Type No.: ML421 Manufactured by Energy Company, Panasonic Corporation.) It must never be subjected to excessive heat or discharge. It must therefore only be fitted in requirement designed specifically for its use. -
Page 8: Service Navigation
3 Service Navigation 3.1. Introduction This service manual contains technical information, which allow service personnel’s to understand and service this model. Please place orders using the parts list and not the drawing reference numbers. If the circuit is changed or modified, the information will be followed by service manual to be controlled with original service manual. 3.2. - Page 9 3.2.1.2. About Mount Box Unit (Ref. 16) 1. This Service Manual does not contain the following repair service information for "MOUNT BOX UNIT"(Ref.16), because it requires special facilities and equipment. a. Schematic diagram, Block diagram and P.C.B. layout. b. Parts list for individual parts. 2.
- Page 10 3.2.2. Lens Unit (Interchangeable Lens: H-FS014042) 3.2.2.1. About Lens Main Block Unit (Ref. 208) 1. This Service Manual does not contain the repair service information for "LENS MAIN BLOCK UNIT"(Ref.208), because it requires special facilities and equipment. 2. The "LENS MAIN BLOCK UNIT"(Ref.208) performance must be confirmed. 3.
- Page 11 3.2.3. Lens Unit (Interchangeable Lens: H-FS045200) 3.2.3.1. About Lens Main Block Unit (Ref. 308) 1. This Service Manual does not contain the repair service information for "LENS MAIN BLOCK UNIT"(Ref.308), because it requires special facilities and equipment. 2. The "LENS MAIN BLOCK UNIT"(Ref.308) performance must be confirmed. 3.
-
Page 12: General Description About Lead Free Solder (Pbf)
3.3. General Description About Lead Free Solder (PbF) The lead free solder has been used in the mounting process of all electrical components on the printed circuit boards used for this equipment in considering the globally environmental conservation. The normal solder is the alloy of tin (Sn) and lead (Pb). On the other hand, the lead free solder is the alloy mainly consists of tin (Sn), silver (Ag) and Copper (Cu), and the melting point of the lead free solder is higher approx.30°C (86°F) more than that of the normal solder. -
Page 13: How To Define The Model Suffix (Ntsc Or Pal Model)
3.4. How to Define the Model Suffix (NTSC or PAL model) There are eight kinds of DMC-G3 (Camera body unit), regardless of the colours. • a) DMC-G3 (Japan domestic model) • b) DMC-G3PP/PC • c) DMC-G3EB/EC/EG/GH/GN • d) DMC-G3EE • e) DMC-G3GK •... - Page 14 3.4.2. INITIAL SETTINGS: After replacing the MAIN P.C.B., make sure to perform the initial settings after achieving the adjustment by ordering the following procedure in accordance with model suffix of the unit. 1. IMPORTANT NOTICE: Before proceeding Initial settings, make sure to read the following CAUTION. 2.
- Page 15 [Only for "EG, EB EC and OLY" models : (VEP56135B is used as a Main P.C.B.)] When MAIN P.C.B. has just been replaced, only 4 model suffix are displayed as follows. [CASE 2. Other than "After replacing MAIN P.C.B."] • Step 5. Choose the model suffix in “INITIAL SETTINGS”: (Refer to “CAUTION”) [Caution: After replacing MAIN P.C.B.] The model suffix can been chosen, JUST ONE TIME.
- Page 16 • Step 7. CONFIRMATION: Confirm the display of “PLEASE SET THE CLOCK” in concerned language when the unit is turned on again. When the unit is connected to PC with USB cable, it is detected as removable media. (When the “GT” or “GK” model suffix is selected, the display shows “PLEASE SET THE CLOCK” in Chinese.) 1) As for your reference, major default setting condition is as shown in the following table.
-
Page 17: Specifications
4 Specifications... -
Page 18: Location Of Controls And Components
5 Location of Controls and Components Names and Functions of Components Camera body Sensor Flash Self-timer indicator / AF Assist Lamp Lens fitting mark Mount Lens lock pin Lens release button [LVF/LCD] button 10 11 12 13 14 15 Diopter adjustment dial 10 Viewfinder 11 Playback button 12 Motion picture button... - Page 19 32 Status indicator 33 Intelligent Auto button 34 Tripod receptacle 35 DC coupler cover When using an AC adaptor, ensure that the Panasonic DC coupler (optional) and AC adaptor (optional) are used. 36 Release lever 37 Card/Battery door 5 3 36 37...
- Page 20 Selecting the Recording Mode To select a Recording Mode with the mode dial Switching the mode by rotating the mode dial. Align a desired mode with part Rotate the mode dial slowly and surely to adjust to each mode. To select Intelligent Auto Mode Press [ ] button will light up when it is switched to Intelligent Auto Mode.
- Page 21 Touch Panel This touch panel is a type that detects pressure. Drag Touch the screen A movement without releasing the touch To touch and release the touch panel. panel. Use this to perform tasks such as selecting This is used to move the AF area, operate icons or images displayed on the touch the slide bar, etc.
-
Page 22: Service Mode
6 Service Mode 6.1. Error Code Memory Function 1. General description This unit is equipped with history of error code memory function, and can be memorized 16 error codes in sequence from the latest. When the error is occurred more than 16, the oldest error is overwritten in sequence. The error code is not memorized when the power supply is shut down forcibly. - Page 23 • Error Code List: The error code consists of 8 bit data and it shows the following information. Important notice about “Error Code List” About "*" indication: The third digit from the left is different as follows. - In case of 0 (example: 2B001000) When the third digit from the left shows “0”, this error occurred under the condition of INITIAL SETTINGS has been com- pleted.
-
Page 24: Troubleshooting Guide
7 Troubleshooting Guide 7.1. Checking Method of Body and Interchangeable Lens... -
Page 29: Service Fixture & Tools
8 Service Fixture & Tools 8.1. Service Fixture and Tools The following Service Fixture and tools are used for checking and servicing this unit. -
Page 30: Clean Box
8.2. Clean Box • The repair quality is considered, and it is recommended working in the environment of satisfied clean level less than class 10,000 (Federal Standard 209D). (When remove the 1st lens frame, it is indispensable.) [NOTE] • Work in the environment of satisfied clean level less than class 10,000 (Federal Standard 209D) when remove the 1st lens frame for cleaning. -
Page 31: Service Position
8.3. Service Position This Service Position is used for checking and replacing parts. Use the following Extension cables for servicing. Table S1 Extension Cable List Parts No. Connection Form RFKZ0583 FP9007(MAIN) - HOT SHOE FPC 19PIN 0.3 FFC RFKZ0477 FP9003(MAIN) - LVF UNIT 45PIN 0.3 FFC VFK1976 FP9005(MAIN) - FPC←→FP8001(TOP) -
Page 32: Disassembly And Assembly Instructions
9 Disassembly and Assembly Instructions 9.1. Camera Body Part Disassembly Flow Chart 9.1.1. This is a disassembling chart. When assembling, perform this chart conversely. P.C.B. Location 9.1.2. - Page 33 Disassembly Procedure 9.1.3. Item Removal Rear Earth Plate (Fig. D17) 4 Screws (P) 1 Screw (Q) Item Removal 2 Screws (R) Rear Case Unit (Fig. D1) 4 Screws (A) (Fig. D18) Grip Piece Rear 8 Screws (B) 2 Locking tabs (Fig.
- Page 34 9.1.3.1. Removal of the Rear Case Unit (Fig. D1) (Fig. D2)
- Page 35 9.1.3.2. Removal of the Main P.C.B. (Fig. D3) (Fig. D4)
- Page 36 (Fig. D5) 9.1.3.3. Removal of the Front Case Unit (Fig. D7) (Fig. D6)
- Page 37 9.1.3.4. Removal of the Mount Box Unit 9.1.3.5. Removal of the Top Case Unit (Fig. D9) 9.1.3.6. Removal of the Flash P.C.B. (Fig. D8) (Fig. D10)
- Page 38 9.1.3.8. Removal of the Battery Case (Fig. D11) 9.1.3.7. Removal of the Battery Door Unit (Fig. D12) (Fig. D13)
- Page 39 9.1.3.9. Removal of the LVF Unit 9.1.3.11. Removal of the Mic P.C.B. (Fig. D16) (Fig. D14) 9.1.3.12. Removal of the Rear Earth Plate 9.1.3.10. Removal of the Top P.C.B. (Fig. D17) (Fig. D15)
- Page 40 9.1.3.14. Removal of the Hinge SW FPC Unit and LCD Unit (Fig. D18) 9.1.3.13. Removal of the Rear Operation P.C.B. (Fig. D19) (Fig. D20)
- Page 41 9.1.3.15. Removal of the LCD IF P.C.B. (Fig. D21) (Fig. D22)
- Page 42 9.1.3.16. Removal of the LCD Unit (Fig. D23) NOTE: (When Installing) Make sure to confirm the following points when installing: • The Screw is tightened enough. • Installing conditions are fine. (No distortion, no abnormal- space.) • No dust and/or dirt on Lens surfaces. •...
-
Page 43: Disassembly And Assemble Procedure For The Lens (H-Fs014042)
9.2. Disassembly and Assemble Procedure for the Lens (H-FS014042) It is recommended dealing with clean box, to keep maintaining the dustproof environment. (Refer to “8.2. Clean Box” section of this service manual for details.) Important: 1. When servicing the enclosure part (refer to Fig. K1), it must be performed inside of satisfied clean level. (Satisfied clean level: Less than class 10,000 (Federal Standard 209D)) As for procedure, refer to the “11 Maintenance”... -
Page 44: Disassembly And Assemble Procedure For The Lens (H-Fs045200)
9.3. Disassembly and Assemble Procedure for the Lens (H-FS045200) It is recommended dealing with clean box, to keep maintaining the dustproof environment. (Refer to “8.2. Clean Box” section of this service manual for details.) Important: 1. When servicing the enclosure part (refer to Fig. W1), it must be performed inside of satisfied clean level. (Satisfied clean level: Less than class 10,000 (Federal Standard 209D)) As for procedure, refer to the “11 Maintenance”... -
Page 45: Measurements And Adjustments
• Inspect it, not only corresponding part is replaced, but also camera body is shocked and/or dropped. • The Panasonic camera body in accordance with the Micro Four Thirds system (DMC-G1 unit, etc. marketed commodity: oper- ates normal) and a standard zoom lens H-FS014045 (marketed commodity: operates normal) is required as a reference machine. - Page 46 *3 NOTE: (After exchange the mount box unit) • Execute the resolution inspection by the comparison with the standard model (DMC-G1K etc.: operates normal). • Refer to the adjustment instruction in the adjustment software for details. • Confirm self recording/playback motion picture of AVCHD mode by the LCD. •...
-
Page 47: Maintenance
11 Maintenance 11.1. Notice in external cleaning 11.1.1. ABOUT THE BODY NOTE: Before cleaning the camera, remove the battery and/or disconnect power plug from the outlet. Also, remove the SD Memory card and lens unit. 11.1.1.1. DUST/DIRT ON THE OUTER CASING PART (S) 1. -
Page 48: General Description (Lens Cleaning: Interchangeable Lens/H-Fs014042)
11.1.2. ABOUT THE LENS 11.1.2.1. DUST/DIRT ON THE OUTER CASING PART(S) 1. Blow off the dust first, then sweep out the dust from narrower spaces with soft cleaning brush. 2. Wipe up the Outer casing part with the dry fuzz-free cloth. 11.1.2.2. - Page 49 11.2.1. Disassembly procedure 11.2.1.3. Removal of a dust /dirt Important: 1. Blow off the dust on the surface of the lens with a blower It must be performed inside of satisfied clean level. brush. (Satisfied clean level: Less than class 10,000 (Federal 2.
- Page 50 11.2.2. Assembly procedure 11.2.2.2. Installation of the Decoration Ring Important: 1. Use the Name Ring fixture (RFKZ0507) When tightening the screw, use a torque driver (RFKZ0456) 2. Use new Decoration ring. (Do not use the one which is by ordering the screwing order with specified torque removed.) described in each step.
-
Page 51: General Description (Lens Cleaning: Interchangeable Lens/H-Fs045200)
11.3. General description (Lens cleaning: Interchangeable Lens/H-FS045200) When there is a dust/dirt inside surface of the 1st lens frame unit and/or subject side surface of the 2nd lens frame unit, remove it by referring the following procedures. Important: 1. When removing the 1st lens frame unit, it has to be proceed inside of satisfied clean level. (Less than class 10,000 (Federal Standard 209D)) As for clean box, refer to the "8.2. - Page 52 11.3.1. Disassembly procedure 11.3.1.2. Removal of the 1st Lens Frame Important: Unit It must be performed inside of satisfied clean level. 1. Remove the 3 screws (A). (Satisfied clean level: Less than class 10,000 (Federal Standard 209D)) 11.3.1.1. Removal of the Decoration Ring 1.
- Page 53 11.3.2. Assembly procedure 2. Tighten the 3 screws (A) with specified torque in numeri- cal order. Important: (Torque Driver: RFKZ0456) When tightening the screw, use a torque driver (RFKZ0456) (Torque: 14.7 ± 1.0 N-cm) by ordering the screwing order with specified torque described in each step.
- Page 54 11.3.2.2. Installation of the Decoration Ring 1. Use the Name Ring fixture (RFKZ0507) 2. Use new Decoration ring. (Do not use the one which is removed.)
- Page 55 DSC1106032CE S1. About Indication of The Schematic Diagram Service Manual S1.1. Important Safety Notice COMPONENTS IDENTIFIED WITH THE MARK HAVE THE SPECIAL CHARACTERISTICS Diagrams and Replacement FOR SAFETY. WHEN REPLACING ANY OF THESE COMPONENTS USE ONLY THE SAME TYPE. 1.Although reference number of the parts is indicated on the P.C.B. drawing and/or Parts List schematic diagrams, it is NOT mounted on the P.C.B.
-
Page 56: S2. Voltage Chart
S2. Voltage Chart Note) Indicated voltage values are the standard values for the unit measured by the DC electronic circuit tester (high-impedance) with the chassis taken as standard. Therefore, there may exist some errors in the voltage values, depending on the internal impedance of the DC circuit tester. S2.1. -
Page 57: S3. Block Diagram
S3. Block Diagram S3.1. Overall Block Diagram MOUNT BOX UNIT IC3101 CARD MOS SENSOR LENS UNIT ANALOG FRONTEND REMOTE TERMINAL IC9101 LENS CONTACT SHUTTER SSWF IC9102,Q9193 SYSTEM IC TERMINAL UNIT MICROPHOME Q4001,4002 MICROPHONE AMP (STEREO) MIC AMP VIDEO OUT IC9901 MOTOR DRIVE AV OUT / DIGITAL TERMINAL... -
Page 58: S4. Schematic Diagram
S4. Schematic Diagram S4.1. Interconnection Diagram TOP P.C.B. FP4202 (COMPONENT SIDE) FP8002 CMD DIAL1 REAR DIAL REG GND PON ON L UNIT MIC FPC CMD DIAL0 FP4201 MIC GND SPEAKER ECM RIN ECM LIN MIC GND STEREO MIC P.C.B. MICROPHONE (FOIL SIDE) POWER FPC BATTERY... -
Page 59: S4.2. Top Operation Schematic Diagram
S4.2. Top Operation Schematic Diagram CAUTION: FOR CONTINUED PROTECTION AGAINST FIRE HAZARD, REPLACE ONLY WITH THE SAME TYPE 2.5A 32V FUSE. ATTENTION: POUR UNE PROTECTION CONTINUE LES RISQUES 2.5A 32V Confidential D' INCENDIE N' UTILISERQUE DES FUSIBLE DE MÉME TYPE 2.5A 32V. Until K1MY23BA0235 FP8001... -
Page 60: S4.3. Flash Schematic Diagram
S4.3. Flash Schematic Diagram CAUTION: FOR CONTINUED PROTECTION AGAINST FIRE HAZARD, REPLACE ONLY WITH THE SAME TYPE 1.5A 32V FUSE. ATTENTION: POUR UNE PROTECTION CONTINUE LES RISQUES 1.5A 32V D' INCENDIE N' UTILISERQUE DES FUSIBLE DE MÉME TYPE 1.5A 32V. To MAIN PCB 1.5A 32V (51281-1040/molex) -
Page 61: S4.4. Rear Operation Schematic Diagram
S4.4. Rear Operation Schematic Diagram DISP R7550 TO MAIN-PCB FP7550 K1MN06BA0272 06FKZ-SM1-GAN-1-ETB(LF)(SN) / JST ZIF-TYPE/ TOP contact PLAY R7552 PLAY S7551 S7550 CROSS_KEY_IN K0F111A00595 K0F111A00591 REAR_KEYIN1 REAR_KEYIN2 QMENU RIGHT DISP/Fn1 R7555 S7552 K0F111A00595 DISP/Fn1 LEFT PLAY DOWN MENU/SET RIGHT DOWN RIGHT MENU/SET LEFT... -
Page 62: S4.5. Mic Schematic Diagram
S4.5. MIC Schematic Diagram POP UP DET SW Connect emitter to collector shortest 0.5mmPitch Backflip Top_Contact FPC CONTACT to MIC_FPC K1MY08BA0370 FP4202 K1MY04BA0370 0.5mmPitch Backflip Top_Contact R4204 FP4201 FPC CONTACT to TOP_OP_FPC 100K[18] ERA3YKD104V MIC_GND R4203 C4203 6.3V ECM_LIN D_GND ECM_RIN INT_DET_SW MIC_GND... -
Page 63: S5. Print Circuit Board
S5. Print Circuit Board S5.1. Top P.C.B. ET8001 FP8001 P8001 (Component Side) S8001 CC8002 CC8001 (Foil Side) DMC-G3/G3K/G3W Top P.C.B. -
Page 64: S5.2. Flash P.c.b
S5.2. Flash P.C.B. P8502 P8503 C8502 D8501 CL8502 C8501 R8512 6 5 4 Q8502 T8501 Q8501 CL8501 CL8505 D8503 R8503 C8504 C8507 C8506 R8507 QR8501 CL8503 QR8502 CL8504 F8501 RL8501 RL8503 DMC-G3/G3K/G3W (Component Side) (Foil Side) Flash P.C.B. S-10... -
Page 65: S5.3. Rear Operation P.c.b
S5.3. Rear Operation P.C.B. S7557 R7550 FP7550 R7551 S7556 (Component Side) (Foil Side) DMC-G3/G3K/G3W Rear Operation P.C.B. S-11... -
Page 66: S5.4. Mic P.c.b
S5.4. MIC P.C.B. S4201 VA4203 FP4202 C4208 R4208 R4207 C4206 C4203 R4203 C4204 R4204 C4207 Q4201 R4205 (Component Side) (Foil Side) DMC-G3/G3K/G3W MIC P.C.B. S-12... -
Page 67: S6. Replacement Parts List
1. In case of the "LENS MAIN BLOCK UNIT" (Ref.208 and Ref.308) defects, contact to the service department of sales company. <DEFINITION OF PARTS SUPPLIER> 1. Parts marked with [ENERGY] in the remarks column are supplied from Panasonic Corporation Energy Company. 2. Parts marked with [SPC] in the remarks column are supplied from AVC-CSC-SPC. - Page 68 DMC-G3EG-K vol.1 Ref.No. Part No. Part Name & Description Remarks Ref.No. Part No. Part Name & Description Remarks ## VEP56135A MAIN P.C.B. (RTL) E.S.D. T8501 G5D1A0000074 TRANSFORMER PP,PC,EE,GC,GH,GT,GN,GD, KPP,KPC,KEE,KGC,KGH,KGT, KGK,KGN,KGD,WPP,WEE,WGC, WGH,WGT,WGK,WGN,WGD ## VEP50086A REAR OPERATION P.C.B. (RTL) ## VEP56135B MAIN P.C.B. 1 (RTL) E.S.D.
- Page 69 DMC-G3EG-K vol.1 Ref.No. Part No. Part Name & Description Remarks Ref.No. Part No. Part Name & Description Remarks VEP59096A LCD IF P.C.B. 1 (RTL) E.S.D. VEP56135B MAIN P.C.B. 1 (RTL) E.S.D. EG,EC,EB, VGQ0V38 LCD BL BEZEL SHEET KEG,KEC,KEB,WEG,WEC,WEB VGQ0Y08 LCD PCB SHEET VEP56135A MAIN P.C.B.
- Page 70 DMC-G3EG-K vol.1 Ref.No. Part No. Part Name & Description Remarks Ref.No. Part No. Part Name & Description Remarks VHD2331-A SCREW VHD2331-A SCREW VHD2331-A SCREW VHD2337 SCREW 1 (-K,-T,-R,-KA) VHD2338 SCREW 1 (-W) VHD2337 SCREW 1 (-K,-T,-R,-KA) VHD2338 SCREW 1 (-W) VHD2337 SCREW 1 (-K,-T,-R,-KA)
- Page 71 DMC-G3EG-K vol.1 Ref.No. Part No. Part Name & Description Remarks Ref.No. Part No. Part Name & Description Remarks VXW1261 LENS UNIT 1 (G3K,G3W)K,T,R,KA [SPC] VXW1267 LENS UNIT 1 (G3K,G3W)W [SPC] VDW2023 SHADING FRAME 1 (G3K,G3W) [SPC] VEJ2295 MOUNT CONTACT UNIT 1 (G3K,G3W) [SPC] VGH5186 DECORATION RING...
- Page 72 DMC-G3EG-K vol.1 Ref.No. Part No. Part Name & Description Remarks Ref.No. Part No. Part Name & Description Remarks VXW1264 LENS UNIT 1 (G3W) K,T,R,KA [SPC] VXW1270 LENS UNIT 1 (G3W) W [SPC] P04F310 DECORATION RING 1 (G3W) [SPC] 9630020 SHADING FRAME 1 (G3W) [SPC] P0479H0 MOUNT CONTACT UNIT...
- Page 73 DMC-G3EG-K vol.1 Ref.No. Part No. Part Name & Description Remarks Ref.No. Part No. Part Name & Description Remarks VQT3N54 BASIC O/I 1 KGN VKF4385 BODY CAP 1 (G3K) (ENGLISH) VPF1316A CAMERA BAG 1 (G3K) VQT3N55 BASIC O/I 1 KGD DE-A94AA/SX BATTERY CHARGER 1 KEG,KEC,KEB,KEE,KGN (KOREAN)
- Page 74 DMC-G3EG-K vol.1 Ref.No. Part No. Part Name & Description Remarks Ref.No. Part No. Part Name & Description Remarks VPK5009 PACKING CASE 1 WPP-K VKF4385 BODY CAP 1 (G3W) VPK5010 PACKING CASE 1 WEG,WEC,WEB-K/R,WEE-K, VPF1316A CAMERA BAG 1 (G3W) WGC,WGH,WGT,WGN,WGD DE-A94AA/SX BATTERY CHARGER 1 WEG,WEC,WEB,WEE,WGN VPK5081...
- Page 75 DMC-G3EG-K vol.1 Ref.No. Part No. Part Name & Description Remarks Ref.No. Part No. Part Name & Description Remarks VPK5003 PACKING CASE 1 EG-K,EC-K,EB-K,EE-K,GC-K, VKF4385 BODY CAP 1 (G3) GH-K,GT-K,GN-K,GD-K VPF1316A CAMERA BAG 1 (G3) VPK5002 PACKING CASE 1 PP-K,PC-K DE-A94AA/SX BATTERY CHARGER 1 EG,EC,EB,EE,GN VPN7251...
-
Page 76: S7. Exploded View
S7. Exploded View S7.1. Frame and Casing Section 93-1 89-1 B52 15 72 73 17-3 B31 B32 17-8 17-1 17-7 17-2 17-9 17-6 17-4 17-5 43 40 S-22... -
Page 77: S7.2. Camera Lens Section (1
S7.2. Camera Lens Section (1) B204 B205 B206 B207 B220 B221 B201 B222 B202 B203 B208 B209 B210 B211 B213 S-23... -
Page 78: S7.3. Camera Lens Section (2
S7.3. Camera Lens Section (2) B313 B317 B301 B303 B302 B305 B304 B306 B307 B318 B309 B311 B308 B310 B312 S-24... -
Page 79: S7.4. Packing Parts And Accessories Section (1
S7.4. Packing Parts and Accessories Section (1) Except PP,PC (DMC-G3KEB/GC/GH) (DMC-G3KEC/EE/EG/GC/GD) (DMC-G3KGT/GK) (DMC-G3KGN) Directions for putting Color Labels, NTSC LABEL and GD LABEL. * Except black color model, stick each color label (Ref. No.421,422,423) inside the “color indication frame” making sure that the bottom part of the color label is even inside the color indication frame. -
Page 80: S7.5. Packing Parts And Accessories Section (2
S7.5. Packing Parts and Accessories Section (2) Except PP,PC (DMC-G3WEB/GC/GH) (DMC-G3WEC/EE/EG/GC/GD) (DMC-G3WGT/GK) (DMC-G3WGN) Directions for putting Color Labels, NTSC LABEL and GD LABEL. * Except black color model, stick each color label (Ref. No.521,522,523) inside the “color indication frame” making sure that the bottom part of the color label is even inside the color indication frame. -
Page 81: S7.6. Packing Parts And Accessories Section (3
S7.6. Packing Parts and Accessories Section (3) Except PP,PC (DMC-G3EB/GC/GH) (DMC-G3EC/EE/EG/GC/GD) (DMC-G3GT) (DMC-G3GN) Directions for putting NTSC LABEL and GD LABEL. * Stick NTSC LABEL (Ref. No.619) to printed “PAL” of the packing case for [GD] and [GT] models. * Stick GD LABEL (Ref. No.618) for [GD] model on the original printed place.