Tally Dascom 7206 Installation And User Manual

Auto cutter

Hide thumbs Also See for 7206:

Programmer's manual (156 pages)

Installation manual/user manual (14 pages)

Installation manual (9 pages)

Table Of Contents

Table of Contents

Quick Links

Download this manual

Installation and

7106 7206

User Guide

Auto Cutter

– 1 –

Table of Contents

Need help?

Do you have a question about the 7206 and is the answer not in the manual?

Questions and answers

Summary of Contents for Tally Dascom 7206

Page 1 Installation and 7106 7206 User Guide Auto Cutter – 1 –...
Page 3 Installation Guide Installing the cutter stand unit Check to make sure that the printer’s power switch is turned off, then disconnect the power cord. Open the top cover. Lift and remove the front cover from the printer. (Keep the removed cover in a safe place, because it is used when the auto cutter has been removed.) –...
Page 4 Feed the cable, in 6, so that it lies along the printer’s case. When replacing the connector cover and the motor cover, take care that the covers do not pinch the cable. Cable Set the cutter-stand-unit to the front of the printer with the screw (2) provided.
Page 5 Remove the screw (1) fastening the motor cover, and then lift and remove the motor cover. Take care that the screw does not fall inside the printer chassis. Remove the screw (1) fastening the optional unit connector cover, and then remove the optional unit connector cover. Plug the connector of the cutter-stand-unit cable into the optional connector on the printer.
Page 6 Installing the cutter unit Plug the connector of the cutter-unit cable into the connector on the cutter stand unit. (10) Align the indentations (2) at the bottom of the cutter unit with the protrusions (2) on the cutter stand unit, and then fasten the slotted head screw on the cutter unit with a...
Page 7: Table Of Contents
User Guide Contents Notice · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 8 SAFETY SIGNS that must be strictly observed! ·...
Page 8: Notice
Notice Before use, be sure to read this manual and understand. And keep it handy for reference when needed. Do not handle, disassemble or repair any parts other than those specified in this manual. The contents of this manual may be changed without prior notice.
Page 9 SAFETY SIGNS that must be strictly observed! To prevent personal injury or property damage, the following must be strictly observed. The degree of possible injury and damage due to incorrect use or improperly following instructions specified is described below. Indicates a situation which, if not observed and handled properly, WARNING could result in death or serious...
Page 10: Safety Signs That Must Be Strictly Observed
CAUTION Avoid the following conditions to ensure proper operation of the auto-cutter. The cutting blade can be very dangerous. Also, this can cause damage. Room temperature is less than 5°C or more than 40°C. Humidity is less than 30% or more than 80%. Dusty Direct sunlight Chemicals...
Page 11: Function
Function The auto-cutter units are designed to cut various media such as labels, tickets and tags precisely and accurately as the setting cut length. Main specifications of auto-cutter Cutting method: Guillotine cutter Maximum cut paper thickness: 0.25 mm (0.01") Minimum cut paper length: 25.4 mm (1") Cut paper width: Maximum: 118 mm (4.65")
Page 12: Checking Items Inside The Accessory Box
Checking items inside the accessory box Auto-cutter is not available for the printer with the peeler. Note You should check that all of the following items are inside the accessory box. If any are missing, please contact your supplier. Cutter Stand Unit ........
Page 13: Auto-Cutter Settings
Auto-cutter settings “Cut On” menu will be selected automatically when the auto-cutter is installed; thus, the printer can be used without adjustment. However, some printers may not have the “AutoConfigure” function. In this case, select the “After Print” menu of the menu setup mode, and the “Cut On” menu on the “Function Select”...
Page 14: Cut Position
CAUTION When a paper jam has occurred, or when the auto cutter has malfunctioned, your supplier or your service representative. Never attempt to repair the auto cutter yourself, it could result in a risk of injury. Cut position The following diagram gives the distance from the media sensor and the thermal printhead to the cutter blade.
Page 15: Cut Settings
Cut settings The auto-cutter-related commands are described below. See the Command Reference manual for more details. The following commands set the cut position and number of operations. Cut-position setup command STX fnnn This command specifies the distance between the sensor and the media cut position.
Page 16: Auto Cut-Length Detection
Auto cut-length detection If media with a cut length shorter than the minimum cut length of 25.4mm (1.0 in) is used, the cut media may remain in the cutter unit and cause paper jams. To prevent this, when the printer detects a cut length shorter than the minimum, it feeds the media without operating the cutter.
Page 17: User Maintenance
User maintenance If the platen of the printer becomes dirty, the cutter may perform defective cutting even if the auto cutter does not malfunction. Therefore, clean the platen regularly. (See the printer user’s manual) Remove the platen Push the head open lever downwards to open the head unit and sensor arm.
Page 18: Troubleshooting
Troubleshooting If an error is detected, an alarm will sound and an LED on the control panel will display the nature of the error. List of error displays Media Out (media location cannot be detected) Auto Cutter Abnormality (such as blade jamming) Abnormal auto-cutter temperature CAUTION...
Page 19 – 19 –...

This manual is also suitable for:

7106

Tally Dascom 7206 Installation And User Manual

Quick Links

Need help?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Tally Dascom 7206

Summary of Contents for Tally Dascom 7206

This manual is also suitable for:

Table of Contents