Using Satellite Channel Table Feature - Toshiba 43V5863DG Operating Instructions Manual

Hide thumbs

Table Of Contents

Table of Contents

satellite search is performed some settings should

be made. A menu will be displayed where you can

select to start M7 or Fransat operator installation or

a standard installation.

To start an M7 operator installation set the Install Type

as Operator and the Satellite Operator as the related

M7 operator. Then highlight Preferred Scan option

and set as Automatic channel scan and press OK

to start the automatic search. These options can be

preselected depending on the Language and Country

selections that you made in the earlier steps of the first

time installation process. You may be asked to select

HD/SD or country specific channel list according to

your M7 operator type. Select one and press OK to

proceed.

Wait till the scan is finished. Now the list has been

installed.

While performing an M7 operator installation, if you

want to use the satellite installation parameters that

differ from the default settings select the Preferred

Scan option as Manual channel scan and press the

OK button to proceed. Antenna Type menu will be

displayed next. After selecting the antenna type and

the desired satellite in the following steps press OK

in order to change the satellite installation parameters

in the sub-menu.

To start a Fransat installation set the Install Type as

Operator

set the Satellite Operator as the

and then

related Fransat operator. Then press the OK button

to start Fransat installation. You can select to start an

automatic or manual installation.

Press OK to proceed. Fransat Installation will be

performed and broadcasts will be stored (if available).

If you set the Install Type as Standard, you can

continue with regular satellite installation and watch

satellite channels.

You can start a Fransat installation at any time later

from the Settings>Installation>Automatic channel

scan> Satellite menu.

In order to search for satellite channels other than

M7 or Fransat channels you should start a standard

installation. Select the Install Type as Standard and

press the OK button to proceed. Antenna Type menu

will be displayed next.

There are three options for antenna selection. You can

select Antenna Type as Direct, Single Satellite Cable

or DiSEqC switch by using Left or Right buttons.

After selecting your antenna type press OK to see

the options to proceed. Continue, Transponder list

and Configure LNB options will be available. You can

change the transponder and LNB settings using the

related menu options.

• Direct: If you have a single receiver and a direct

satellite dish, select this antenna type. Press OK to

continue. Select an available satellite on the next

screen and press OK to scan for services.

• Single Satellite Cable: If you have multiple

receivers and a single satellite cable system, select

this antenna type. Press OK to continue. Configure

settings by following instructions on the next screen.

Press OK to scan for services.

• DiSEqC switch: If you have multiple satellite dishes

and a DiSEqC switch, select this antenna type.

Press OK to continue. You can set four DiSEqC

options (if available) on the next screen. Press OK

button to scan the first satellite in the list.

Analogue: If Analogue broadcast search option is

turned on, the TV will search for analogue broadcasts

after other initial settings are completed.

A dialogue screen asking to activate parental control

will be displayed. If you select Yes, parental restriction

options will be displayed. Configure as desired and

press OK when finished. Select No and press OK

to advance, if you don't want to activate parental

restrictions.

After the initial settings are completed TV will start

to search for available broadcasts of the selected

broadcast types.

While the search continues current scan results will

be displayed at the bottom of the screen. After all the

available stations are stored, Channels menu will be

displayed. You can edit the channel list according to

your preferences using the Edit tab options or press

the Menu button to quit and watch TV.

While the search continues a message may appear,

asking whether you want to sort channels according

to the LCN(*). Select Yes and press OK to confirm.

(*) LCN is the Logical Channel Number system that organizes

available broadcasts in accordance with a recognizable

channel number sequence (if available).

Notes:

To search for M7 channels after the First Time Installation,

you should perform the first time installation again. Or press the

Menu button and enter the Settings>Installation>Automatic

channel scan>Satellite menu. Then follow the same steps

mentioned above

Do not turn off the TV while initializing first time installation.

Note that, some options may not be available depending on

the country selection.