SMC Networks TigerSwitch SMC6152L2 Installation Manual
  1. Manuals
  2. Brands
  3. SMC Networks Manuals
  4. Network Router
  5. SMC6152L2
  6. Installation manual

SMC Networks TigerSwitch SMC6152L2 Installation Manual

Tigerswitch 10/100 48-port 10/100 mbps fast ethernet managed switch
Hide thumbs Also See for TigerSwitch SMC6152L2:
Table of Contents

Advertisement

Quick Links

Download this manual
TigerSwitch 10/100
48-Port 10/100 Mbps
Fast Ethernet Managed Switch
◆ 48 auto-MDI/MDI-X 10/100BASE-TX ports
◆ 4 Gigabit RJ-45 ports shared with 4 SFP transceiver slots
◆ Non-blocking switching architecture
◆ Spanning Tree Protocol, Rapid STP, and MSTP
◆ Up to 6 LACP or static trunks
◆ CoS support through four priority queues
◆ Full support for VLANs with GVRP
◆ IGMP multicast filtering and snooping
◆ Support for jumbo frames up to 9 KB
◆ Manageable via console, Web, SNMP, RMON

Installation Guide

Installationsanleitung
SMC6152L2

Advertisement

Table of Contents
loading

Related Manuals for SMC Networks TigerSwitch SMC6152L2

Summary of Contents for SMC Networks TigerSwitch SMC6152L2

  • Page 1: Installation Guide

    TigerSwitch 10/100 48-Port 10/100 Mbps Fast Ethernet Managed Switch ◆ 48 auto-MDI/MDI-X 10/100BASE-TX ports ◆ 4 Gigabit RJ-45 ports shared with 4 SFP transceiver slots ◆ Non-blocking switching architecture ◆ Spanning Tree Protocol, Rapid STP, and MSTP ◆ Up to 6 LACP or static trunks ◆...
  • Page 3 TigerSwitch 10/100 Installation Guide From SMC’s Tiger line of feature-rich workgroup LAN solutions 20 Mason Irvine, CA 92618 Phone: (949) 679-8000 February 2007 Pub. # 150000050600A...
  • Page 4 Irvine, CA 92618 All rights reserved. Printed in Taiwan Trademarks: SMC is a registered trademark; and EZ Switch, TigerStack and TigerSwitch are trademarks of SMC Networks, Inc. Other product and company names are trademarks or registered trademarks of their respective holders.
  • Page 5 All SMC products carry a standard 90-day limited warranty from the date of purchase from SMC or its Authorized Reseller. SMC may, at its own discretion, repair or replace any product not operating as warranted with a similar or functionally equivalent product, during the applicable warranty term.
  • Page 6 RIGHTS, WHICH MAY VARY FROM STATE TO STATE. NOTHING IN THIS WARRANTY SHALL BE TAKEN TO AFFECT YOUR STATUTORY RIGHTS. * SMC will provide warranty service for one year following discontinuance from the active SMC price list. Under the limited lifetime warranty, internal and external power supplies, fans, and cables are covered by a standard one-year warranty from date of purchase.
  • Page 7 OMPLIANCES FCC - Class A This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.

  • Page 8: Ce Mark Declaration Of Conformance For Emi And Safety

    OMPLIANCES CE Mark Declaration of Conformance for EMI and Safety (EEC) SMC contact for these products in Europe is: SMC Networks Europe, Edificio Conata II, Calle Fructuós Gelabert 6-8, 2 08970 - Sant Joan Despí, Barcelona, Spain. This information technology equipment complies with the requirements of the Council...
  • Page 9 Faserkabelenden schauen, während diese eingeschaltet sind. Power Cord Safety Please read the following safety information carefully before installing the switch: WARNING: Installation and removal of the unit must be carried out by qualified personnel only. • The unit must be connected to an earthed (grounded) outlet to comply with international safety standards.
  • Page 10 U.K. Europe Veuillez lire à fond l'information de la sécurité suivante avant d'installer le Switch: AVERTISSEMENT: L’installation et la dépose de ce groupe doivent être confiés à un personnel qualifié. • Ne branchez pas votre appareil sur une prise secteur (alimentation électrique) lorsqu'il n'y a pas de connexion de mise à...
  • Page 11 France et Pérou uniquement: Ce groupe ne peut pas être alimenté par un dispositif à impédance à la terre. Si vos alimentations sont du type impédance à la terre, ce groupe doit être alimenté par une tension de 230 V (2 P+T) par le biais d’un transformateur d’isolement à...

  • Page 12: Warnings And Cautionary Messages

    Warning: This switch uses lasers to transmit signals over fiber optic cable. The lasers are compliant with the requirements of a Class 1 Laser Product and are inherently eye safe in normal operation. However, you should never look directly at a transmit port when it is powered on.

  • Page 13: End Of Product Life Span

    The following publication gives specific information on how to operate and use the management functions of the switch: The SMC6152L2 Management Guide Also, as part of the switch’s firmware, there is an online web-based help that describes all management related features.
  • Page 14 OMPLIANCES...

  • Page 15: Table Of Contents

    Overview ..........1-1 Switch Architecture ........1-2 Network Management Options .
  • Page 16 Troubleshooting ......A-1 Diagnosing Switch Indicators ....... . . A-1 Power and Cooling Problems .
  • Page 17 Standards ..........C-3 Compliances .
  • Page 18 ABLE OF ONTENTS...
  • Page 19 ABLES Table 1-1 Port Status LEDs ....... . . 1-4 Table 1-2 System Status LEDs .
  • Page 21 Attaching the Brackets ......3-5 Figure 3-3 Installing the Switch in a Rack ..... 3-5 Figure 3-4 Attaching the Adhesive Feet .
  • Page 22 IGURES xviii...

  • Page 23: Figure 1-1 Front And Rear Panels

    SNMP-based management agent embedded on the main board. This agent supports both in-band and out-of-band access for managing the switch. This switch provides a broad range of powerful features for Layer 2 switching, delivering reliability and consistent performance for your network traffic.

  • Page 24: About The Tigerswitch

    The SMC6152L2 switch employs a wire-speed, non-blocking switching fabric. This permits simultaneous wire-speed transport of multiple packets at low latency on all ports. The switch also features full-duplex capability on all ports, which effectively doubles the bandwidth of each connection.

  • Page 25: Sfp Slots

    (purchased separately) is installed in a slot and has a valid link on the port, the associated RJ-45 port is disabled and cannot be used. The switch can also be configured to force the use of an RJ-45 port or SFP slot, as required.

  • Page 26: Table 1-1 Port Status Leds

    BOUT THE IGER WITCH Condition RJ-45 Ports Link/ACT On/Blinking (Link/ Green Activity) On/Blinking Amber Combination Gigabit Ports Link/ACT/ On/Blinking 1000M Green (Link/ On/Blinking Activity/ Amber 1000M) Table 1-1 Port Status LEDs Status The port has established a valid 100 Mbps link. Blinking indicates activity.

  • Page 27: Power Supply Socket

    Condition On Green (Power) On Amber Diag On Green Blinking Green On Amber Power Supply Socket There is one standard power socket on the rear panel for the AC power cord. Table 1-2 System Status LEDs Status The unit’s internal power supply is operating normally.

  • Page 28: Features And Benefits

    BOUT THE IGER WITCH Features and Benefits Connectivity • 48 10/100BASE-TX ports plus 4 Gigabit combination ports (RJ-45/ SFP). • Auto-negotiation enables each RJ-45 port to automatically select the optimum speed (10 or 100 Mbps), and the communication mode (half or full duplex) if this feature is supported by the attached device;...

  • Page 29: Management

    Supports flow control, using back pressure for half duplex and IEEE 802.3x for full duplex • Broadcast storm control Management • “At-a-glance” LEDs for easy troubleshooting • Network management agent: Manages switch in-band or out-of-band Supports Telnet, SNMP (v1/v2), RMON (4 groups), and Web-based interface EATURES AND ENEFITS...
  • Page 30 BOUT THE IGER WITCH...

  • Page 31: Network Planning

    When networks are based on repeater (hub) technology, the distance between end stations is limited by a maximum hop count. However, a switch turns the hop count back to zero. So subdividing the network into smaller and more manageable segments, and linking them to the larger network by means of a switch, removes this limitation.

  • Page 32: Application Examples

    Fast Ethernet ports built into the front panel or a Gigabit Ethernet port on a plug-in SFP transceiver. In the figure below, the switch is operating as a collapsed backbone for a small LAN. It is providing dedicated full-duplex connections to workstations, power users, and servers.

  • Page 33: Network Aggregation Plan

    In the figure below, the 10/100BASE-TX ports are providing 100 Mbps connectivity for up to 48 segments. In addition, the switch is also connecting several servers at 1000 Mbps. Figure 2-2 Network Aggregation Plan...

  • Page 34: Remote Connections With Fiber Cable

    A 1000BASE-SX (MMF) link can connect to a site up to 550 meters away, a 1000BASE-LX (SMF) link up to 5 km, and a 1000BASE-ZX link up to 100 km. This allows the Switch to serve as a collapsed backbone, providing direct connectivity for a widespread LAN.

  • Page 35: Making Vlan Connections

    PPLICATION XAMPLES Making VLAN Connections This switch supports VLANs which can be used to organize any group of network nodes into separate broadcast domains. VLANs confine broadcast traffic to the originating group, and can eliminate broadcast storms in large networks. This provides a more secure and cleaner network environment.

  • Page 36: Application Notes

    1. Full-duplex operation only applies to point-to-point access (such as when a switch is attached to a workstation, server or another switch). When the switch is connected to a hub, both devices must operate in half-duplex mode. 2. Avoid using flow control on a port connected to a hub unless it is actually required to solve a problem.

  • Page 37: Installing The Switch

    NSTALLING THE Selecting a Site Switch units can be mounted in a standard 19-inch equipment rack or on a flat surface. Be sure to follow the guidelines below when choosing a location. • The site should: be at the center of all the devices you want to link and near a power outlet.

  • Page 38: Ethernet Cabling

    NSTALLING THE WITCH Ethernet Cabling To ensure proper operation when installing the switch into a network, make sure that the current cables are suitable for 10BASE-T, 100BASE-TX or 1000BASE-T operation. Check the following criteria against the current installation of your network: •...

  • Page 39: Equipment Checklist

    • This Installation Guide • Management Guide CD • SMC Warranty Registration Card—be sure to complete and return to Optional Rack-Mounting Equipment If you plan to rack-mount the switch, be sure to have the following equipment available: • Four mounting screws for each device you plan to install in a rack—these are not included...

  • Page 40: Mounting

    NSTALLING THE WITCH Mounting This switch can be mounted in a standard 19-inch equipment rack or on a desktop or shelf. Mounting instructions for each type of site follow. Rack Mounting Before rack mounting the switch, pay particular attention to the following factors: •...

  • Page 41: Figure 3-2 Attaching The Brackets

    1. Attach the brackets to the device using the screws provided in the Bracket Mounting Kit. Figure 3-2 Attaching the Brackets 2. Mount the device in the rack, using four rack-mounting screws (not provided). Figure 3-3 Installing the Switch in a Rack OUNTING...

  • Page 42: Desktop Or Shelf Mounting

    2. Set the device on a flat surface near an AC power source, making sure there are at least two inches of space on all sides for proper air flow. 3. If installing a single switch only, go to “Connecting to a Power Source” at the end of this chapter.

  • Page 43: Installing An Optional Sfp Transceiver

    3. Slide the SFP transceiver into the slot until it clicks into place. Note: SFP transceivers are hot-swappable. The switch does not need to be powered off before installing or removing a transceiver.

  • Page 44: Connecting To A Power Source

    NSTALLING THE WITCH Connecting to a Power Source To connect a switch to a power source: 1. Insert the power cable plug directly into the power socket located at the back of the switch. 2. Plug the other end of the cable into a grounded, 3-pin, AC power source.

  • Page 45: Connecting To The Console Port

    Connecting to the Console Port The DB-9 serial port on the switch’s rear panel is used to connect to the switch for out-of-band console configuration. The command-line-driven configuration program can be accessed from a terminal or a PC running a terminal emulation program.
  • Page 46 NSTALLING THE WITCH 3-10...

  • Page 47: Making Network Connections

    Connecting Network Devices The SMC6152L2 switch is designed to interconnect multiple segments (or collision domains). It can be connected to network cards in PCs and servers, as well as to hubs, switches or routers. It may also be connected to remote devices using the optional SFP transceivers.

  • Page 48: Connecting To Pcs, Servers, Hubs And Switches

    Figure 4-1 Making Twisted-Pair Connections 2. If the device is a network card and the switch is in the wiring closet, attach the other end of the cable segment to a modular wall outlet that is connected to the wiring closet. (See the section “Network Wiring Connections”...

  • Page 49: Network Wiring Connections

    1. Attach one end of a patch cable to an available port on the switch, and the other end to the patch panel. 2. If not already in place, attach one end of a cable segment to the back of the patch panel where the punch-down block is located, and the other end to a modular wall outlet.

  • Page 50: Fiber Optic Sfp Devices

    50/125 or 62.5/125 micron multimode fiber optic cabling with an LC connector at both ends. Warning: This switch uses lasers to transmit signals over fiber optic cable. The lasers are compliant with the requirements of a Class 1 Laser Product and are inherently eye safe in normal operation.

  • Page 51: Figure 4-3 Making Fiber Port Connections

    3. Connect one end of the cable to the LC port on the switch and the other end to the LC port on the other device. Since LC connectors are keyed, the cable can be attached in only one orientation.

  • Page 52: Connectivity Rules

    However, note that because switches break up the path for connected devices into separate collision domains, you should not include the switch or connected cabling in your calculations for cascade length involving other devices.

  • Page 53: 100 Mbps Fast Ethernet Collision Domain

    Table 4-2 Maximum 1000BASE-SX Gigabit Ethernet Cable Lengths Fiber Size 62.5/125 micron multimode fiber 50/125 micron multimode fiber Table 4-3 Maximum 1000BASE-LX Gigabit Ethernet Cable Length Fiber Size 9/125 micron single-mode fiber Table 4-4 Maximum 1000BASE-ZX Gigabit Ethernet Cable Length Fiber Size 9/125 micron single-mode fiber...

  • Page 54: 10 Mbps Ethernet Collision Domain

    • Note the length of each cable and the maximum cable length supported by the switch ports. • For ease of understanding, use a location-based key when assigning prefixes to your cable labeling.

  • Page 55: Troubleshooting

    • Be sure the cable is plugged into both the switch and • If the switch is installed in a rack, check the connections to the • Verify that the proper cable type is used and its length does not •...

  • Page 56: Power And Cooling Problems

    Then verify that you entered the correct IP address. Also, be sure the port through which you are connecting to the switch has not been disabled. If it has not been disabled, then check the network cabling that runs between your remote location and the switch.

  • Page 57: Cables

    Caution: DO NOT plug a phone jack connector into any RJ-45 port. This will damage the switch. Use only twisted-pair cables with RJ-45 connectors that conform with FCC standards. The figure below illustrates how the pins on the RJ-45 connector are numbered.

  • Page 58: Table B-1 10/100Base-Tx Mdi And Mdi-X Port Pinouts

    1, 2, 3, and 6, at one end of the cable, are connected straight through to pins 1, 2, 3, and 6 at the other end of the cable. When using any RJ-45 port on this switch, you can use either straight-through or crossover cable. Table B-1 10/100BASE-TX MDI and MDI-X Port Pinouts...

  • Page 59: Twisted-Pair Cable And Pin Assignments

    “X” (MDI-X) or neither port is labeled with an “X” (MDI), a crossover must be implemented in the wiring. (When auto-negotiation is enabled for any RJ-45 port on this switch, you can use either straight-through or crossover cable to connect to any device type.) You must connect all four wire pairs as shown in the following diagram to support Gigabit Ethernet connections.

  • Page 60: 1000Base-T Pin Assignments

    ABLES End A 1000BASE-T Pin Assignments All 1000BASE-T ports support automatic MDI/MDI-X operation, so you can use straight-through cables for all network connections to PCs or servers, or to other switches or hubs. The table below shows the 1000BASE-T MDI and MDI-X port pinouts. These ports require that all four pairs of wires be connected.

  • Page 61: 1000Base-T Cable Requirements

    Table B-2 1000BASE-T MDI and MDI-X Port Pinouts MDI Signal Name Bi-directional Data One Plus (BI_D1+) Bi-directional Data One Minus (BI_D1-) Bi-directional Data Two Plus (BI_D2+) Bi-directional Data Three Plus (BI_D3+) Bi-directional Data Three Minus (BI_D3-) Bi-directional Data Two Minus (BI_D2-) Bi-directional Data Four Plus (BI_D4+) Bi-directional Data Four Minus (BI_D4-) 1000BASE-T Cable Requirements...

  • Page 62: Fiber Standards

    ABLES Note that when testing your cable installation, be sure to include all patch cables between switches and end devices. Adjusting Existing Category 5 Cabling to Run 1000BASE-T If your existing Category 5 installation does not meet one of the test parameters for 1000BASE-T, there are basically three measures that can be applied to try and correct the problem: 1.

  • Page 63: Specifications

    Physical Characteristics Ports 48 10/100BASE-TX, with auto-negotiation 4 Combination Gigabit Ports (RJ-45/SFP) Network Interface Ports 1-48: RJ-45 connector, auto MDI/X 10BASE-T: RJ-45 (100-ohm, UTP cable; Category 3 or better) 100BASE-TX: RJ-45 (100-ohm, UTP cable; Category 5 or better) Ports 49-52: RJ-45 connector, auto MDI/X 1000BASE-T: RJ-45 (100-ohm, UTP cable;...

  • Page 64: Switch Features

    Internal, auto-ranging transformer: 100 to 240 VAC, 50 to 60 Hz, 1A Power Consumption 30 Watts maximum Maximum Current 0.25 A @ 115 VAC 0.12 A @ 230 VAC Switch Features Forwarding Mode Store-and-forward Throughput Wire speed Flow Control Full Duplex: IEEE 802.3-2005...

  • Page 65: Standards

    Software Loading TFTP in-band, or XModem out-of-band Standards IEEE 802.3-2005 Ethernet, Fast Ethernet, Gigabit Ethernet Full-duplex flow control IEEE 802.1D Spanning Tree Protocol IEEE 802.1w Rapid Spanning Tree Protocol ISO/IEC 8802-3 Compliances CE Mark Emissions FCC Class A Industry Canada Class A EN55022 (CISPR 22) Class A EN 61000-3-2/3 VCCI Class A...
  • Page 66 PECIFICATIONS...

  • Page 67: Table D-1 Tigerswitch 10/100 Products And Accessories

    RDERING Table D-1 TigerSwitch 10/100 Products and Accessories Product Number Description SMC6152L2 48 10/100BASE-TX ports, and four Gigabit combination ports that are comprised of a RJ-45 port and an SFP transceiver slots. SMCBGSLCX1 1-port 1000BASE-SX Small Form Pluggable (SFP) mini-GBIC transceiver SMCBGLLCX1 1-port 1000BASE-LX Small Form Pluggable (SFP) mini-GBIC transceiver...

  • Page 68: Ordering Information

    RDERING NFORMATION...

  • Page 69: German Instructions

    Eine Site Auswählen (Selecting a Site - German) Die Switch können in ein Standard-19-Zoll-Ausrüstungsgestell oder auf eine flache Ebene montiert werden. Zum Auswählen eines Standortes beachten Sie bitte die nachstehenden Richtlinien. • Die Site sollte: - Sich in der Mitte aller anzuschließenden Geräte sowie in der Nähe einer Netzsteckdose befinden;...

  • Page 70: Montage (Rack Mounting Instructions - German

    Fur alle Geräte wird empfohlen, einen Filter oder einen Überspannungsschutz zu verwenden. Montage (Rack Mounting Instructions - German) Switch-Einheiten können an ein standardmäßiges 19-Zoll Einrichtungsrack, einen Arbeitstisch oder ein Regal montiert werden. Folgend finden Sie die Montageanweisungen für jeden Positionstyp.

  • Page 71: Anschluss An Eine Stromquelle (Connecting To A Power Source - German

    Schrauben an dem Gerät. 2. Befestigen Sie das Gerät mit vier Rackmontageschrauben (nicht beigelegt) an dem Rack. 3. Wenn Sie nur einen Switch installieren, dann springen Sie bitte über zu "Verbinden mit einer Stromquelle" auf Seite 3-8 am Ende dieses Kapitels.
  • Page 72 ERMAN NSTRUCTIONS Hinweis: Im Ausland müssen Sie eventuell ein anderes Netzkabel verwenden. Wählen Sie dazu ein zugelassenes, für die Steckdosen des jeweiligen Landes passendes Netzkabel. 3. Überzeugen Sie sich davon, dass das Gerät mit Strom versorgt wird: Die Betrieb-LED („Power“) an der Vorderseite muss leuchten. Falls nicht, schauen Sie nach, ob das Netzkabel richtig eingesteckt ist.
  • Page 73 10BASE-T IEEE 802.3 specification for 10 Mbps Ethernet over two pairs of Category 3, 4, or 5 UTP cable. 100BASE-TX IEEE 802.3u specification for 100 Mbps Ethernet over two pairs of Category 5 UTP cable. 1000BASE-LX IEEE 802.3z specification for Gigabit Ethernet over two strands of 50/ 125, 62.5/125 or 9/125 micron core fiber cable.
  • Page 74 Bandwidth The difference between the highest and lowest frequencies available for network signals. Also synonymous with wire speed, the actual speed of the data transmission along the cable. Collision A condition in which packets transmitted over the cable interfere with each other.
  • Page 75 Full Duplex Transmission method that allows two network devices to transmit and receive concurrently, effectively doubling the bandwidth of that link. Gigabit Ethernet A 1000 Mbps network communication system based on Ethernet and the CSMA/CD access method. IEEE Institute of Electrical and Electronic Engineers. IEEE 802.3 Defines carrier sense multiple access with collision detection (CSMA/CD) access method and physical layer specifications.

  • Page 76: Network Diameter

    Light emitting diode used for monitoring a device or network condition. Local Area Network (LAN) A group of interconnected computer and support devices. Media Access Control (MAC) A portion of the networking protocol that governs access to the transmission medium, facilitating the exchange of data between network nodes.
  • Page 77 Telecommunications Industry Association Transmission Control Protocol/Internet Protocol (TCP/IP) Protocol suite that includes TCP as the primary transport protocol, and IP as the network layer protocol. Unshielded twisted-pair cable. Virtual LAN (VLAN) A Virtual LAN is a collection of network nodes that share the same collision domain regardless of their physical location or connection point in the network.
  • Page 78 Glossary-6...

  • Page 79: Index

    Ethernet connectivity rules 4-8 Fast Ethernet connectivity rules 4-7 features C-2 management 1-7 switch 1-6 fiber cables 4-4 flow control, IEEE 802.3x 1-3 front panel of switch 1-1 full duplex connectivity 2-1 Gigabit Ethernet cable lengths 4-6 grounding for racks 3-4 NDEX Index-1...
  • Page 80 NDEX IEEE 802.3x flow control 1-3 indicators, LED 1-3 installation connecting devices to the switch 4-2 desktop or shelf mounting 3-6 network wiring connections 4-3 port connections 4-1 power requirements 3-1 problems A-2 site requirements 3-1 wiring closest connections 4-3...
  • Page 81 IEEE C-3 status LEDs 1-3 switch architecture 1-2 switching introduction to 2-1 method 1-2 Telnet A-2 temperature within a rack 3-4 TigerSwitch 10/100 Products and Accessories D-1 troubleshooting in-band access A-2 power and cooling problems A-2 switch indicators A-1 twisted-pair connections 4-1...
  • Page 82 NDEX Index-4...
  • Page 84 CIS: PRC: Taiwan: Asia Pacific: Korea: Japan: Australia: India: If you are looking for further contact information, please visit www.smc.com. 20 Mason Irvine, CA 92618 Phone: (949) 679-8000 (800) SMC-4-YOU Fax (949) 679-1481 34-91-352-00-40 Fax 34-93-477-3774 44 (0) 871 277 98 02...

This manual is also suitable for:

6152l2

Table of Contents