Table of Contents
Advertisement
Quick Links
Introducing the Cool SATA to USB 2.0
The Cool Dual SATA to USB 2.0 Docking is designed to
support USB equipped computers.
provides large capacity mobile storage using 3.5" or 2.5"
SATA hard disk drives through high-speed, hot-
swapping USB 2.0 interface.
Features and Benefits
•
Two hard drive docking bays
•
Supports Hi-Speed USB 2.0 port
•
Supports SATA I/II (SATA 150/300)
•
Supports 2.5" and 3.5" hard drive
•
Plug and Play, no additional drivers needed
•
Supports USB hot-swap and hot-plug
System Requirements
PC:
•
Pentium
USB port (USB 2.0 recommended)
•
Windows
2008 (32-/64-bit) / Vista (32-/64-bit)
Mac
:
®
•
An available USB port (USB 2.0 recommended)
•
Mac OS
04-0523A
Cool Dual SATA to
USB 2.0 Docking
Quick Installation Guide
or equivalent computer with an available
®
2000 / XP (32-/64-bit) / Server 2003 &
®
X v10.4.8 or higher
®
This adapter
1
Advertisement
Table of Contents
Related Manuals for SIIG SC-SA0412-S1
Summary of Contents for SIIG SC-SA0412-S1
- Page 1 Cool Dual SATA to USB 2.0 Docking Quick Installation Guide Introducing the Cool SATA to USB 2.0 The Cool Dual SATA to USB 2.0 Docking is designed to support USB equipped computers. provides large capacity mobile storage using 3.5" or 2.5" SATA hard disk drives through high-speed, hot- swapping USB 2.0 interface.
-
Page 2: Package Contents
Package Contents • Cool Dual SATA to USB 2.0 Docking • Switching power adapter • USB 2.0 cable (type A to type B) • Quick Installation Guide Layout Note: You cannot use one hard drive in both platforms, Windows and Mac. It is not supported SATA Drive Slot LED (Two LED's stay on while the unit is on) -
Page 3: Hardware Installation
Hardware Installation Make sure the SATA connectors are in alignment. Gently insert the SATA hard drive into the SATA drive slot. Plug the included switching power adapter into the Cool Dual SATA to USB 2.0 Docking power adapter jack, then plug the switching power adapter into a reliable power source. - Page 4 Using the Cool Dual SATA to USB 2.0 Windows One drive icon for each inserted SATA hard drive will appear in My Computer when the converter is plugged into a USB port. The drive(s) act just like a conventional hard drive in your system. Note: Be careful not to touch the hard drive while in use.
- Page 5 Windows XP/Server 2003 & 2008 Verify that the HDD LED(s) are OFF before proceeding. Double click the Safely Remove Hardware icon located in the system tray. Highlight USB Mass Storage Device, click Stop, OK then Close. You can now unplug or turn off the Cool Dual SATA to USB 2.0 Docking.
- Page 6 Blank Page...
- Page 7 Step 1: Submit your RMA request. Go to www.siig.com, click Support, then RMA to submit a request to SIIG RMA. If the product is determined to be defective, an RMA number will be issued. Step 2: After obtaining an RMA number, ship the product.
- Page 8 Fremont, CA 94538-3152, USA Ph: 510-657-8688 Cool Dual SATA to USB 2.0 Docking is a trademark of SIIG, Inc. SIIG and the SIIG logo are registered trademarks of SIIG, Inc. Microsoft, Windows and Windows Vista are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. Pentium is a registered trademark of Intel Corporation.
Need help?
Do you have a question about the SC-SA0412-S1 and is the answer not in the manual?
Questions and answers