Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for IFM O3R222
Summary of Contents for IFM O3R222
- Page 1 Operating instructions 2D/3D camera head O3R222 O3R225 O3R252...
-
Page 2: Table Of Contents
O3R222 / O3R252 ........ -
Page 3: Preliminary Note
If the warning is not observed, damage to property is possible. 1.3 Legal and copyright information © All rights reserved by ifm electronic gmbh. No part of these instructions may be reproduced and used without the consent of ifm electronic gmbh. -
Page 4: Safety Instructions
O3R222 O3R225 O3R252 2D/3D camera head 2 Safety instructions • The unit described is a subcomponent for integration into a system. – The system architect is responsible for the safety of the system. – The system architect undertakes to perform a risk assessment and to create documentation in accordance with legal and normative requirements to be provided to the operator and user of the system. -
Page 5: Cyber Security
2D/3D camera head O3R222 O3R225 O3R252 Warning against opening the device or damaging it WARNING If the device has been opened or damaged, laser safety is no longer guaranteed. w Skin or eye damage may occur. u The device may only be opened by the manufacturer. -
Page 6: Intended Use
O3R222 O3R225 O3R252 2D/3D camera head 3 Intended use The unit features a TOF (Time Of Flight) camera and, additionally, an RGB camera. The TOF camera measures the distance between the camera and the object for each pixel by means of the time-of-flight principle. For this purpose, the objects are illuminated with the internal infrared light source. -
Page 7: Installation
2D/3D camera head O3R222 O3R225 O3R252 4 Installation Fig. 1: Installation of the device 1 Device 2 Field of view and illumination range of the device 3 Area to be kept free 4 Area without requirements Installing the device: u Do not place any objects in area (3). -
Page 8: Heat Management
O3R222 O3R225 O3R252 2D/3D camera head 4.1 Heat management ATTENTION The device can heat up depending on the operating mode, the set parameters and the heat dissipation to the environment. The difference between the device’s surface temperature and the ambient temperature must not exceed 25 degrees (according to IEC61010-2-201). -
Page 9: Electrical Connection
2D/3D camera head O3R222 O3R225 O3R252 5 Electrical connection The device must be connected by a qualified electrician. u Disconnect power before connecting the device. u Use strain reliefs for cables connected to the device. Protection class III device (IEC 61010-2-201 chap. 6.5.2.101.4). -
Page 10: Wiring
O3R222 O3R225 O3R252 2D/3D camera head 5.1 Wiring Fig. 2: Wiring 1 TOF camera (coaxial connection) 2 RGB camera (coaxial connection) -
Page 11: Scale Drawings
2D/3D camera head O3R222 O3R225 O3R252 6 Scale drawings 6.1 O3R222 / O3R252 18,7 41,7 41,7 Fig. 3: Scale drawing 1 RGB camera 2 TOF camera 3 Illumination unit... - Page 12 O3R222 O3R225 O3R252 2D/3D camera head 6.2 O3R225 18,7 41,7 41,7 Fig. 4: Scale drawing 1 RGB camera 2 TOF camera 3 Illumination unit...
-
Page 13: Maintenance, Repair And Disposal
2D/3D camera head O3R222 O3R225 O3R252 7 Maintenance, repair and disposal Soiling reduces the contrast and the recognition performance. u Keep the front pane free from soiling. u Do not open the device. w The device does not contain any components which can be maintained by the user. The device must only be repaired by the manufacturer. -
Page 14: Approvals/Standards
O3R222 O3R225 O3R252 2D/3D camera head 8 Approvals/standards For approvals and standards, the following information is available: • Test standards and regulations: documentation.ifm.com • EU declaration of conformity and approvals: documentation.ifm.com • Notes relevant for approval: package inserts of the device... -
Page 15: Glossary
2D/3D camera head O3R222 O3R225 O3R252 Glossary Convection Convection is the air movement around the unit. Sufficient air movement is necessary to prevent the unit from overheating.