Table of Contents
Advertisement
Quick Links
Introducing the CyberSerial Dual PCIe-DB
The CyberSerial Dual PCIe-DB high-speed serial I/O card
provides two additional 9-pin serial ports.
Features and Benefits
•
Compliant with PCI Express Base Specification 1.0a
•
PCI Express 1-lane (x1) serial I/O card works with
PCI Express slots with different lane width
•
Installs into any available PCI Express slot and
provides two 9-pin RS232 serial ports
•
32-byte FIFO buffers dramatically increase data
transmit/receive speed and supports data rates up
to 230 Kbps
•
Works as standard RS232 port or with 5V or 12V
power output for devices that require power
System Requirements
•
PCI Express-enabled system with an available PCI
Express slot
•
Windows 2000/XP/Server 2003
Package Contents
•
CyberSerial Dual PCIe-DB adapter
•
Connector bracket with 9-pin serial port (for the 2nd
serial port)
•
"Y" split power cable
•
Driver CD and user's manual
04-0404A
CyberSerial Dual PCIe-DB
Quick Installation Guide
1
Advertisement
Table of Contents
Related Manuals for SIIG JJ-E10D11-S2
Summary of Contents for SIIG JJ-E10D11-S2
- Page 1 CyberSerial Dual PCIe-DB Quick Installation Guide Introducing the CyberSerial Dual PCIe-DB The CyberSerial Dual PCIe-DB high-speed serial I/O card provides two additional 9-pin serial ports. Features and Benefits • Compliant with PCI Express Base Specification 1.0a • PCI Express 1-lane (x1) serial I/O card works with PCI Express slots with different lane width •...
- Page 2 Layout Connector bracket with 9-pin serial port (optional) Serial port 1 Figure 1: CyberSerial Dual PCIe-DB Board Layout * Note: If the serial port requires power output, connect the system power source to board's power connector. However, most serial devices do not require additional power through the serial port.
-
Page 3: Hardware Installation
Hardware Installation General instructions for installing the card are provided below. Since the design of computer cases and motherboards vary, refer to your computer’s reference manual for further information, if needed. Static Electricity Discharge may permanently damage your system. Discharge any static electricity build up in your body by touching your computer’s case for a few seconds. -
Page 4: Driver Installation
To install the card, carefully align the card's bus connector with the selected PCI Express slot on the motherboard. Push the board down firmly, but gently, until it is well seated. Replace the slot bracket's holding screw to secure the card. Replace the computer cover and reconnect the power cord. - Page 5 Repeat steps 1-5 two times. Restart Windows to complete the installation. Windows XP At the Found New Hardware Wizard, select No, not this time, then click Next. Select Install from a list or specific location (Advanced), then click Next. Insert the driver CD, check Include this location in the search, uncheck the other box, type in D:\XP, and click Next.
- Page 6 Right click My Computer, click Manage, then click Device Manager. Click on the + (plus sign) in front of Ports (COM & LPT), a SIIG serial port should be displayed two times. Double click Multifunction adapters, a SIIG serial board should be displayed.
-
Page 7: Technical Support And Warranty
RMA number posted on the outside of the shipping carton. • You are responsible for the cost of shipping the product to SIIG at the following address: SIIG, Inc. 6078 Stewart Avenue... - Page 8 Fremont, CA 94538-3152 CyberSerial Dual PCIe-DB is a trademark of SIIG, Inc. SIIG and SIIG logo are registered trademarks of SIIG, Inc. Microsoft and Windows are registered trademarks of Microsoft Corporation. Other names used in publication are for identification only and may be trademarks of their respective companies.
Need help?
Do you have a question about the JJ-E10D11-S2 and is the answer not in the manual?
Questions and answers