Advertisement
Quick Links
AKT 699
GB
LIGHTING THE BURNERS
•
To ignite one of the burners, turn the relative knob anti-clockwise to the maximum flame setting
•
Press the knob against the control panel to ignite the burner.
•
After the burner has ignited, keep the knob pressed for about 5 seconds to allow the thermocouple to warm up.
This burner safety device shuts off the gas supply to the burner if the flame goes out accidentally (because of sudden
draught, an interruption in the gas delivery, boiling over of liquids, etc.).
•
The device must not be pressed for more than 15 sec. If, after that time has elapsed, the burner does not
remain lit, wait at least one minute before trying to light it again.
-
The burner might go out when the knob is released. This means that the thermocouple has not warmed up enough.
In this case, repeat the operations described above.
PRATICAL ADVICE FOR USING THE BURNERS
For better burner performance, please stick to the following
rules:
-
Use pots and pans that fit the burners (see table on the
right).
-
Only use flat-bottomed pots and pans.
-
Use the correct amount of water for cooking foods and
keep the pot covered.
-
In the case of pans with convex bottoms (WOK), use
the support grille provided, which should be positioned
only on the 4 ring burner.
5019 319 62045/B
PRODUCT DESCRIPTION SHEET
Removable panstand grids
1.
Auxiliary burner
2.
Semi-rapid burner
3.
Semi-rapid burner
4.
4 ring burner (WOK)
5.
Auxiliary burner control knob
6.
Semi-rapid burner control knob
7.
Semi-rapid burner control knob
8.
4 ring burner control knob
9.
SYMBOLS
Tap closed
Maximum flame
Minimum flame
.
Burner
Pot Ø
4 ring burner
from 24 to 26 cm
semi-rapid
from 16 to 22 cm
auxiliary
from 8 to 14 cm
To get full satisfaction from the hob, please read these instructions carefully and keep them for future consultation.
DIMENSIONS AND DISTANCES TO BE MAINTAINED (mm)
NOTE: In case of installation of a hood above the cooktop, please refer to the hood instructions for the correct
distance.
NG
BURNER
Pressure
Injector
(kPa)
Front RHS (Auxiliary)
1.00
Rear RHS (Semi-rapid)
1.00
Rear LHS (Semi-rapid)
1.00
Front LHS (4 rings WOK)
1.00
ELECTRIC SUPPLY: 230 - 240 V ~ 50 Hz
ULPG
Rate
Pressure
Injector
(mm)
MJ/h
(kPa)
(mm)
0.85
4.0
2.75
0.55
1.15
7.0
2.75
0.75
1.15
7.0
2.75
0.75
1.75
14.8
2.75
1
AU
Rate
MJ/h
4.0
8.0
8.0
15.1
Advertisement
Related Manuals for Whirlpool AKT 699
Summary of Contents for Whirlpool AKT 699
- Page 1 AKT 699 PRODUCT DESCRIPTION SHEET Removable panstand grids DIMENSIONS AND DISTANCES TO BE MAINTAINED (mm) Auxiliary burner Semi-rapid burner Semi-rapid burner 4 ring burner (WOK) Auxiliary burner control knob Semi-rapid burner control knob Semi-rapid burner control knob 4 ring burner control knob...
- Page 2 20 mm from the bottom of the hob. In the case that you SIDE CLEARANCE intend to install an oven beneath the hob, make sure that it is manufactured by Whirlpool and equipped with a cooling system. The manufacturer declines all liability if another brand oven is installed beneath the Where the distance measured between the periphery of the burner and any vertical combustible surface is less than 200mm, hob.
- Page 3 INSTALLATION ELECTRICAL CONNECTION • The electrical connections must comply with local GAS CONNECTION Earth regulations. (yellow/green) • The data relevant to the voltage and power absorption Check the “gas type” sticker attached to the hotplate. Details of the injector sizes used are recorded on the data plate are indicated on the rating plate.
- Page 4 • Stainless steel surfaces may be stained by calcareous water or aggressive detergents if left in contact for too long. Any Whirlpool Europe S.r.l. food spills (water, sauce, coffee, etc.) should be wiped away before they dry. Viale G. Borghi, 27 Clean with warm water and neutral detergent, and then dry with a soft cloth or chamois.