Liquiphant with electronic insert fel67 (24 pages)
Summary of Contents for Endress+Hauser Liquiphant FTL51B
Page 1
Products Solutions Services XA01810F-C/00/EN/04.22-00 71569643 2023-04-04 Safety Instructions Liquiphant FTL51B, FTL63 ATEX, IECEx: Ex ia IIC T6 Ga/Gb Ex ia IIC T6 Gb Ex ia IIIC Txxx°C Da/Db Ex ia IIIC Txxx°C Db...
XA01810F-C Liquiphant FTL51B, FTL63 Associated All documentation is available on the Internet: www.endress.com/Deviceviewer documentation (enter the serial number from the nameplate). If not yet available, a translation into EU languages can be ordered. To commission the device, please observe the Operating Instructions...
Liquiphant FTL51B, FTL63 XA01810F-C EU type-examination certificate Certificate number: KIWA 19ATEX0017X List of applied standards: See EU Declaration of Conformity. IEC Declaration of Conformity Certificate number: IECEx KIWA 19.0010X Affixing the certificate number certifies conformity with the following standards (depending on the device version): •...
Page 6
XA01810F-C Liquiphant FTL51B, FTL63 Structure of the extended order code FTL51B, – ************* A*B*C*D*E*F*G*.. FTL63 (Device (Basic (Optional type) specifications) specifications) * = Placeholder At this position, an option (number or letter) selected from the specification is displayed instead of the placeholders.
Page 7
Liquiphant FTL51B, FTL63 XA01810F-C Basic specifications Position 1, 2 (Approval) Selected option Description FTL51B ATEX II 1/2 G Ex ia IIC T6...T1 Ga/Gb FTL63 ATEX II 2 G Ex ia IIC T6...T1 Gb ATEX II 1/2 D Ex ia IIIC Txxx°C Da/Db ATEX II 2 D Ex ia IIIC Txxx°C Db IECEx Ex ia IIC T6...T1 Ga/Gb...
Page 8
XA01810F-C Liquiphant FTL51B, FTL63 Position 7 (Electrical Connection) Selected option Description FTL51B Gland M20, brass nickel plated, IP66/68 NEMA Type 4X/6P FTL63 Gland M20, 316L, IP66/68 NEMA Type 4X/6P Thread M20, IP66/68 NEMA Type 4X/6P Thread G1/2, IP66/68 NEMA Type 4X/6P...
Page 9
Liquiphant FTL51B, FTL63 XA01810F-C Position 10 (Type of Probe) Selected option Description FTL51B Compact version FTL63 Extension tube Short tube version Shown in the temperature tables exemplary as follows: Optional specifications ID Jx, Kx (Test, Certificate, Declaration) Selected option...
XA01810F-C Liquiphant FTL51B, FTL63 ID Px, Rx (Accessory Enclosed) Selected option Description FTL51B Weather protection cover, 316L FTL63 Weather protection cover, plastic Test magnet Only in connection with Position 6 = M Only in connection with Position 6 = B, C Only in connection with Position 3, 4 = A8 •...
Page 11
Liquiphant FTL51B, FTL63 XA01810F-C • Limitations of the maximum ambient temperature at the electronics enclosure may be required dependent on device configuration, process temperatures and temperature classification. • Details of limitations: → 15, "Temperature tables". • To avoid electrostatic charging: Do not rub surfaces with a dry cloth.
XA01810F-C Liquiphant FTL51B, FTL63 Safety instructions: Installation A0025536 1 Zone 1, Zone 21 Tank; Zone 0, Zone 1, Zone 20, Zone 21 Electronic insert Enclosure Basic specification, Position 3, 4 = A7, A8: Associated intrinsically safe power supply units...
Page 13
Liquiphant FTL51B, FTL63 XA01810F-C • Observe the maximum process conditions according to the manufacturer' s Operating Instructions. • At high medium temperatures, note flange pressure load capacity as a factor of temperature. • Install the device to exclude any mechanical damage or friction during the application.
XA01810F-C Liquiphant FTL51B, FTL63 Accessory high pressure sliding sleeve The high pressure sliding sleeve can be used for a continuous setting of the switch point and is suited for zone separation if mounted properly (see Operating Instructions). Intrinsic safety • The device is only suitable for connection to certified, intrinsically safe equipment with explosion protection Ex ia / Ex ib.
Liquiphant FTL51B, FTL63 XA01810F-C Temperature Optional specification, ID Jx, Kx = JL Lower limit of the ambient temperature for explosion protection tables changes to –50 °C. Optional specification, ID Jx, Kx = JN Lower limit of the ambient temperature for explosion protection changes to –52 °C.
Page 16
XA01810F-C Liquiphant FTL51B, FTL63 Zone 20, Zone 21 or Zone 21 1st column: Position 8 = A, B, ... 2nd column: Process temperature range in °C 3rd column: Ambient temperature range in °C 4th column: Maximum surface temperature in °C A0039764 Ambient temperature in °C...
Page 17
Liquiphant FTL51B, FTL63 XA01810F-C Position 3, 4 = A7 Without Optional specification, ID Mx = MR, MS A, B –50 –40 –50 –40 –50 –50 –52 –52 –50 –50 –50 –50 T3...T1 –50 –50 In connection with Position 3, 4 = A8 and Optional specification, ID Nx, Ox = NG: The temperature classes change to T4...T1...
Page 18
XA01810F-C Liquiphant FTL51B, FTL63 Position 3, 4 = A8 Without Optional specification, ID Mx = MR, MS A, B –50 –40 –50 –40 –50 –50 –52 –52 –50 –50 –50 –50 T3...T1 –50 –50 In connection with Position 3, 4 = A8 and Optional specification, ID Nx, Ox = NG: The temperature classes change to T4...T1...
Page 19
Liquiphant FTL51B, FTL63 XA01810F-C Position 3, 4 = GA Without Optional specification, ID Mx = MR, MS –50 –40 –50 –40 T5...T1 –50 –40 –50 –40 With Optional specification, ID Mx = MR, MS –50 –40 –50 –40 T5...T1 –50 –40...
Page 20
XA01810F-C Liquiphant FTL51B, FTL63 Zone 20, Zone 21 Zone 21 Zone 20 A, B –50 ≤ T ≤ +150 –40 ≤ T ≤ +60 Zone 20: T –25 to +165 –50 ≤ T ≤ +60 Zone 21: T –48 to +155...
Page 21
Liquiphant FTL51B, FTL63 XA01810F-C Zone 21 Zone 21 Zone 21 A, B –50 ≤ T ≤ +150 –40 ≤ T ≤ +60 –48 to +155 –50 ≤ T ≤ +60 –52 ≤ T ≤ +60 Only in connection with Optional specification, ID Jx, Kx = JL...
XA01810F-C Liquiphant FTL51B, FTL63 Connection data Optional specification, ID Nx, Ox = NF, NG When using the Bluetooth® module: No changes to the connection values. Associated intrinsically safe power supply unit with max. electrical specifications below the characteristic values of the electronic inserts...
Page 23
Liquiphant FTL51B, FTL63 XA01810F-C Ex ia IIIC Cable gland: Basic specification, Position 7 = B mandatory for Position 6 = B, M Thread Clamping range Material Sealing insert O-ring M20x1,5 ø 8 to 10.5 mm Ms, nickel-plated Silicone EPDM (ø 17x2)