Inovance GL20-1600ETP User Manual

Inovance GL20-1600ETP User Manual

Digital output module

Advertisement

*PS00005972A01*

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the GL20-1600ETP and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Inovance GL20-1600ETP

  • Page 1 *PS00005972A01*...
  • Page 3: Standard Compliance

    Preface ■ About This Guide GL20‑0016ETP series 16‑channel digital PNP transistor output module can be used together with a PLC master such as Easy series. This guide describes the mechanical installation, electrical installation and programming examples of the product. ■ Standard Compliance The following table lists the certifications, directives, and standards that the product may comply with.
  • Page 4: Revision History

    This guide is not delivered with the product. You can obtain the PDF version by the following method: http://en.inovance.cn/ Log in to Inovance's website ( ), choose Support > Download, search by keyword, and then download the PDF file. ‑...
  • Page 5: Safety Instructions

    4. Use this equipment according to the designated environment requirements. Damage caused by improper use is not covered by warranty. 5. Inovance shall take no responsibility for any personal injuries or property damage caused by improper use. ■ Safety Levels and Definitions : Indicates that failure to comply with the notice will result in severe personal injuries or even death.
  • Page 6: Installation

    An emergency stop circuit, a protection circuit, a forward/reverse operation interlocked ● circuit, and a upper position limit and lower position limit interlocked circuit must be set in the external circuits of PLC to prevent damage to the machine. To ensure safe operation, for the output signals that may cause critical accidents, design ●...
  • Page 7 Prevent metal filings and wire ends from dropping into ventilation holes of the PLC ● during installation. Failure to comply may result in fire, fault and malfunction. Ensure there are no foreign matters on ventilation surface. Failure to comply may result ●...
  • Page 8 Maintenance & inspection must be carried out by personnel who have the necessary ● electrical training and experience. Do not touch the terminals while the power is on. Failure to comply may result in electric ● shock or malfunction. Disconnect all external power supplies of the system before cleaning the module or re‑ ●...
  • Page 9 1 产品信息 Model Number and Nameplate ⑤ Module Type ① Product Information ③ I/O Points GL: General local 00: Zero input E: Logic I/O expansion module module ② Serial Number ④ I/O Points ⑥ Output type R: Relay output 20: 20 series module 16: 16 outputs TP: Transistor output (sourcing)
  • Page 10 Based on the above description of model number and nameplate, the relevant ordering data of this product is described in the following table. Model Description Product Code Applicable Model GL20‑ GL20 series 16‑channel digital 01440292 AC800 series, Easy series 0016ETP transistor output module Components Description...
  • Page 11: Power Supply Specifications

    Description Name Red: Digital output Orange: Analog output Color Gray: Digital input Green: Analog input identification White: Blue: Other module Communication Specifications ■ Power supply specifications Item Specification Rated bus input voltage 5 VDC (4.75 VDC to 5.25 VDC) Rated bus input current 85 mA (typical@5 V) Rated terminal input voltage 24 VDC (20.4 VDC to 28.8 VDC)
  • Page 12: Software Specifications

    Item Specification Switching frequency 100 Hz with resistive load, 0.5 Hz with inductive load, 10 Hz with lamp load Isolation Output action display Output indicators are turned ON (via software control) when the outputs are in the driving state Output derating 50% derating at 55°C (the output current does not exceed 1A when all outputs are ON ), or 10°C derating when all outputs are Protection function...
  • Page 13: Mounting Dimensions

    2 Mechanical Installation Mounting Dimensions ■ Module The mounting dimensions (in mm) are shown in the figure below. ■ Cable Connection ‑ ‑...
  • Page 14: Installation Method

    Installation Method ■ Installing Modules Side-by-Side You can install multiple modules side by side with the help of top and bottom guides on the modules, as shown below. ■ Installing Module onto DIN Rail You can install the module onto a DIN rail. Align the module with the DIN rail and push the module in the direction indicated by the arrow until you hear a click, as shown below.
  • Page 15: Removing Module

    ■ Removing Module Pry the DIN rail mounting hook upwards with a tool such as slotted screwdriver, hold the protrusions and pull the module out straight forward, and then press down the top of the DIN rail mounting hook. ‑ ‑...
  • Page 16: Cable Selection

    3 Electrical Installation Cable Selection The cable lug and cable diameter included in the following table are only for reference. Material Applicable Cable Diameter Suzhou Yuanli Name Model Crimping Model Crimping Tool Tool Tubular E0308 KST2000L 0308 YAC‑5 E0508 0508 0.75 E7508 7508...
  • Page 17: Terminal Definition

    Terminal Definition Left Indicator Left Signal Left Terminal Right Right Signal Right Terminal Indicator 24 V Terminal Wiring External Wiring ‑ ‑...
  • Page 18 ‑ ‑...
  • Page 19: Programming Examples

    4 Programming Examples The following is an example where the input voltage of channel 0 of the GL20‑ 0016ETP module is assigned to the corresponding variable, and AC802 is used as the master control module. 1. Add GL20‑0016ETP module. 2. In Channels Config interface of the GL20‑0016ETP module, set Output status after stop or disconnection of each channel.
  • Page 20 3. Define variables output_CH0 and output_CH1 with the ST programming language. 4. Map the defined variable output_CH0 to Group 0 (DO7‑DO0) of the configured GL20‑0016ETP module. 5. After successful compiling, download the project and run it. ‑ ‑...

Table of Contents