Table of Contents
Advertisement
Important Safeguards
These safety instructions are to ensure the long life of your projector
and to prevent fire and shock. Please read them carefully and heed all
warnings.
Installation
1. Place the projector on a flat, level surface and in a dry area free from
dust and moisture.
2. Do not place the projector in direct sunlight, near heaters or heat
radiating appliances.
3. Exposure to direct sunlight, smoke or steam could harm internal com-
ponents.
4. Handle your projector carefully. Dropping or jarring your projector could
damage internal components.
5. Do not place heavy objects on top of the projector.
6. If you wish to have the projector installed on the ceiling:
a Do not attempt to install the projector yourself.
b The projector must be installed by qualified technicians in order to ensure
proper operation and reduce the risk of bodily injury.
c In addition, the ceiling must be strong enough to support the projector
and the installation must be in accordance with any local building codes.
d Please consult your dealer for more information.
e Do not attempt to stack projectors on the ceiling.
To Dealer or Installer:
To prevent the projector from falling, install it in a place and fasten it in a
way with sufficient strength to support the combined weight (58.2 kg/
128.3 lbs) of the projector (43 kg/94.8 lbs), the lens (10 kg/22 lbs) and
the ceiling mount(5.2 kg/11.5 lbs) for an extended period of time as well
as to withstand earthquakes.
Power Supply
1. The projector is designed to operate on a power supply of 1.4 KW
AC100-120 / 1.7KW AC200-240V 50/60Hz. Ensure that your power
supply fits this requirement before attempting to use your projector.
2. Handle the power cable carefully and avoid excessive bending. A
damaged cord can cause electric shock or fire.
3. If the projector will not be used for an extended period of time, dis-
connect the plug from the power outlet.
4. Placing the power cord and the RGB cable closely to each other can
cause beat noise. If this happens, keep the two separated so that
beat noise is not generated.
For Europe
Two types of power cables are supplied with the projector: Three-pin
type for U.S.A and Canada; and Two-pin type for Europe.
Cleaning
1. Unplug the projector before cleaning.
2. Clean the cabinet periodically with a damp cloth. If heavily soiled,
use a mild detergent. Never use strong detergents or solvents such
as alcohol or thinner.
3. Use a blower or lens paper to clean the lens, and be careful not to
scratch or mar the lens.
For North America
Fire and Shock Precautions
1. Ensure that there is sufficient ventilation and that vents are unob-
structed to prevent potentially dangerous concentrations of ozone
and the build-up of heat inside your projector. Allow at least 8 inches
(20cm) of space between your projector and a wall. Allow at least 20
inches (50 cm) of space between the ventilation duct outlet and ob-
ject.
2. Prevent foreign objects such as paper clips and bits of paper from
falling into your projector. Do not attempt to retrieve any objects that
might fall into your projector. Do not insert any metal objects such as
a wire or screwdriver into your projector. If something should fall into
your projector, disconnect it immediately and have the object removed
by a qualified your service person.
3. Do not place any liquids on top of your projector.
CAUTION: High Pressure Lamp May Explode if Improperly Handled.
Refer Servicing to Qualified Service Personnel.
Lamp Caution: Please read before operation
Due to the lamp being sealed in a pressurized environment there is
a small risk of explosion if not operated correctly. There is minimal
risk involved if the unit is in proper working order. The risk of explo-
sion increases if the unit is damaged or operated beyond the lamp
life*. Please note that there is a warning system built in that displays
the following message when you reach the end of usable lamp life;
"The lamp has reached the end of its usable life. Please replace
the lamp." When you see this message please contact your Digital
Projection Dealer for a replacement lamp. If the lamp does explode,
smoke will be discharged from the vents located on the side of the
unit. This smoke is comprised of glass in particle form mixed with
Xenon gas and will not cause harm if kept out of your eyes. If your
eyes have been exposed to this gas, please flush your eyes out with
water immediately and seek immediate medical attention. Do not rub
your eyes! This could cause serious injury.
* The lamp life is typically 1500 hours. When Long Life mode is se-
lected in Lamp mode, you can extend the lamp life up to 2000
hours. See page E-36 for Lamp Mode.
WARNING: Do not look into the lens while the projector is on. Seri-
ous damage to your eyes could result.
CAUTION
Do not unplug the power cable from the wall outlet under any one of
the following circumstances. Doing so can cause damage to the
projector:
• While the message "Now storing..." appears. This message will
be displayed after the projector is turned off.
• Immediately after the power cable is plugged into the wall outlet
(the POWER indicator has not changed to a steady amber glow).
• Immediately after the cooling fan stops working (After the projec-
tor is turned off with the POWER OFF button the cooling fan con-
tinues to work for 3 minutes while the Two Digit INDICATOR "--"
flashes).
E – iii
Advertisement
Table of Contents
