Download Print this page
NAPCO GEMINI C Series Programming Instructions Manual
NAPCO GEMINI C Series Programming Instructions Manual

NAPCO GEMINI C Series Programming Instructions Manual

Hide thumbs Also See for GEMINI C Series:

Advertisement

Quick Links

Publicly traded on NASDAQ
Symbol: NSSC
HARDWIRE
GEMINI C-Series CONTROL PANELS / COMMUNICATORS
Programming the Gemini C-Series Control Panels with
or the GEMC-BK1 Burglary Keypad for Burglary Only systems
11/02/28
GEMC-FK1 Keypad
© NAPCO 2023
PROGRAMMING
G E M C - 2 5 5
G E M C - 1 2 8
G E M C - 9 6
G E M C - 3 2
COMMERCIAL / RESIDENTIAL
the GEMC-FK1 Fire Keypad
SYSTEM NORMAL
12:05 AM
INSTRUCTIONS
VOLUME 2
KEYPAD
WIRELESS
SYSTEM READY
11/02/28
12:05 AM
GEMC-BK1 Keypad
WI1673ELF-2 (Vol 2) 2/23

Advertisement

loading
Need help?

Need help?

Do you have a question about the GEMINI C Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for NAPCO GEMINI C Series

  • Page 1 Programming the Gemini C-Series Control Panels with the GEMC-FK1 Fire Keypad or the GEMC-BK1 Burglary Keypad for Burglary Only systems SYSTEM READY SYSTEM NORMAL 11/02/28 12:05 AM 11/02/28 12:05 AM GEMC-FK1 Keypad GEMC-BK1 Keypad WI1673ELF-2 (Vol 2) 2/23 © NAPCO 2023...
  • Page 2: Important Note

    SILENCE BYPASS Warning: The use of non-NAPCO wireless devices with this control panel has not been evaluated by UL and voids the UL listing. In addition, the performance of these devices can not be guaranteed as compatible with NAPCO control panels. For systems that include CO detectors, the system must be monitored by a central station.
  • Page 3 System Delays & Timeouts ............55 Limited Warranty ..............120 Keypad System Codes ............. 56 CS Receiver Format Options ........... 57 Refer to accompanying Gemini C-Series Control Panel Installation Instructions (WI1653) for installation information. NAPCO Gemini C-Series Control Panel Programming Instructions--Volume 2 NAPCO Security Group...
  • Page 4 "Binary" format). DETERMINE THE DATA ENTRIES Referring to the ZONE FEATURES page in the programming worksheets that follow, "Exit/Entry Follower" for zones 1 through 8 are located at address 2018. NAPCO Gemini C-Series Control Panel Programming Instructions--Volume 2 NAPCO Security Group...
  • Page 5 Address 5306. The existing data will display and the cursor will ad- 5306 vance to the data field. 5. Press . The numbers 015 will appear on the keypad display indicating the number of seconds entered. NAPCO Gemini C-Series Control Panel Programming Instructions--Volume 2 NAPCO Security Group...
  • Page 6: Hexadecimal Format

    PROGRAM THE DATA ENTRIES 1. Enter the panel's Dealer Security Code, then press 2. Answer NO to all questions until "ACTIVATE PROGRAM Y/N" is displayed; then press YES. NOTE: If you pass NAPCO Gemini C-Series Control Panel Programming Instructions--Volume 2 NAPCO Security Group...
  • Page 7 (via the keypad) their custom default program or to make minor field alterations to an existing control panel program. The panel MUST be uploaded to NAPCO's PCD-Windows software following any keypad program- ming; the PCD-Windows's error-check feature must be utilized to reduce the possibility of programming omissions or conflicts.
  • Page 8 1. Select the desired option entering the option number (1-8) for each digit.  2. Enter corresponding option number in address location. NOTE: Dark shaded data value box shows option not available. Press to save. NAPCO Gemini C-Series Control Panel Programming Instructions--Volume 2 NAPCO Security Group...
  • Page 9 Select the desired option entering the option number (1-8) for each digit.  Enter corresponding option number in address location. NOTE: Dark shaded data value box shows option not available.  Press to save. NAPCO Gemini C-Series Control Panel Programming Instructions--Volume 2 NAPCO Security Group...
  • Page 10 Select the desired option entering the option number (1-8) for each digit.  Enter corresponding option number in address location. NOTE: Dark shaded data value box shows option not available.  Press to save. NAPCO Gemini C-Series Control Panel Programming Instructions--Volume 2 NAPCO Security Group...
  • Page 11 NOTE: Dark shaded data value box shows option not avail- (address 8179)). Zone Area 1 is enabled for the first 8 zones able. only, by default. Disable Auto-Reset on non-Fire zones for SIA CP-01 installa- tions. NAPCO Gemini C-Series Control Panel Programming Instructions--Volume 2 NAPCO Security Group...
  • Page 12 NOTE: Dark shaded data value box shows option not avail- (address 8179)). Zone Area 1 is enabled for the first 8 zones able. only, by default. Disable Auto-Reset on non-Fire zones for SIA CP-01 installa- tions. NAPCO Gemini C-Series Control Panel Programming Instructions--Volume 2 NAPCO Security Group...
  • Page 13 NOTE: Dark shaded data value box shows option not avail- (address 8179)). Zone Area 1 is enabled for the first 8 zones able. only, by default. Disable Auto-Reset on non-Fire zones for SIA CP-01 installa- tions. NAPCO Gemini C-Series Control Panel Programming Instructions--Volume 2 NAPCO Security Group...
  • Page 14 NOTE: Dark shaded data value box shows option not avail- (address 8179)). Zone Area 1 is enabled for the first 8 zones able. only, by default. Disable Auto-Reset on non-Fire zones for SIA CP-01 installa- tions. NAPCO Gemini C-Series Control Panel Programming Instructions--Volume 2 NAPCO Security Group...
  • Page 15 NOTE: Dark shaded data value box shows option not avail- (address 8179)). Zone Area 1 is enabled for the first 8 zones able. only, by default. Disable Auto-Reset on non-Fire zones for SIA CP-01 installa- tions. NAPCO Gemini C-Series Control Panel Programming Instructions--Volume 2 NAPCO Security Group...
  • Page 16 NOTE: Dark shaded data value box shows option not avail- (address 8179)). Zone Area 1 is enabled for the first 8 zones able. only, by default. Disable Auto-Reset on non-Fire zones for SIA CP-01 installa- tions. NAPCO Gemini C-Series Control Panel Programming Instructions--Volume 2 NAPCO Security Group...
  • Page 17 NOTE: Dark shaded data value box shows option not avail- (address 8179)). Zone Area 1 is enabled for the first 8 zones able. only, by default. Disable Auto-Reset on non-Fire zones for SIA CP-01 installa- tions. NAPCO Gemini C-Series Control Panel Programming Instructions--Volume 2 NAPCO Security Group...
  • Page 18 NOTE: Dark shaded data value box shows option not avail- (address 8179)). Zone Area 1 is enabled for the first 8 zones able. only, by default. Disable Auto-Reset on non-Fire zones for SIA CP-01 installa- tions. NAPCO Gemini C-Series Control Panel Programming Instructions--Volume 2 NAPCO Security Group...
  • Page 19 NOTE: Dark shaded data value box shows option not avail- (address 8179)). Zone Area 1 is enabled for the first 8 zones able. only, by default. Disable Auto-Reset on non-Fire zones for SIA CP-01 installa- tions. NAPCO Gemini C-Series Control Panel Programming Instructions--Volume 2 NAPCO Security Group...
  • Page 20 NOTE: Dark shaded data value box shows option not avail- (address 8179)). Zone Area 1 is enabled for the first 8 zones able. only, by default. Disable Auto-Reset on non-Fire zones for SIA CP-01 installa- tions. NAPCO Gemini C-Series Control Panel Programming Instructions--Volume 2 NAPCO Security Group...
  • Page 21 NOTE: Dark shaded data value box shows option not avail- (address 8179)). Zone Area 1 is enabled for the first 8 zones able. only, by default. Disable Auto-Reset on non-Fire zones for SIA CP-01 installa- tions. NAPCO Gemini C-Series Control Panel Programming Instructions--Volume 2 NAPCO Security Group...
  • Page 22 (address 8179)). Zone Area 1 is enabled for the first 8 zones able; see Direct Address Programming Example on page only, by default. Disable Auto-Reset on non-Fire zones for SIA CP-01 installa- tions. NAPCO Gemini C-Series Control Panel Programming Instructions--Volume 2 NAPCO Security Group...
  • Page 23 Fire, Pulse Alarm Output and Fire Verification is enabled for the zone numbers entered in "FIRE ZONES". Note: See "Number of Zones & Keypads per Area" in Easy Menu Driven program Mode. NAPCO Gemini C-Series Control Panel Programming Instructions--Volume 2 NAPCO Security Group...
  • Page 24 Supervision Disabled NAC D Horn/Strobe Simultaneous Silence Enable Panel Relay Fire Trouble Relay Keypad 1 Always Unlocked for User Functions RESERVED All Keypads Unlocked for Silence, Reset and Supp. NAPCO Gemini C-Series Control Panel Programming Instructions--Volume 2 NAPCO Security Group...
  • Page 25 7926 NOTE: A is not permitted. Wireless Tamper 7927 3. To disable a code leave boxes blank (•). [Default = blank (•) from address 7925-7927] 4. Press to save. NAPCO Gemini C-Series Control Panel Programming Instructions--Volume 2 NAPCO Security Group...
  • Page 26 Valid entries in the right nibble are: 01 through 03 as speci- SLC BURG 1/2 (GEMC-BSLC Burg SLC) fied in the RECEIVER TYPE table. Note: Left nibble is al- SLC FIRE 1/2 (GEMC-FW-SLC Fire SLC) ways blank (•) NAPCO Gemini C-Series Control Panel Programming Instructions--Volume 2 NAPCO Security Group...
  • Page 27 ONBOARD NAC/RELAY TYPES 8061 Option Default BURG Relay Board FIRE Relay Board FIRE NAC Board PCB SLOT 1 PCB SLOT 2 Reserved Reserved Reserved BLANK=DEFAULTS BURG RELAY BOARD ON BURG BUS NAPCO Gemini C-Series Control Panel Programming Instructions--Volume 2 NAPCO Security Group...
  • Page 28: Event Description

    Keypad Features tab) contains a non-functional "Unattended Download Mode" checkbox that is checked when enabled and grayed-out when disabled. Note: Unattended downloading from a computer is NOT allowed for Fire Alarm UL installations. NAPCO Gemini C-Series Control Panel Programming Instructions--Volume 2 NAPCO Security Group...
  • Page 29 Programming Example on page 72.  3. Press to save. NOTE: Dark shaded data value box shows option not available for that Area. Area 1 is a Fire Area only. NAPCO Gemini C-Series Control Panel Programming Instructions--Volume 2 NAPCO Security Group...
  • Page 30 Select the desired option entering the option number (1-8) for each digit.  Enter corresponding option number in address location.  Press to save. NOTE: Dark shaded data value box shows option not available. NAPCO Gemini C-Series Control Panel Programming Instructions--Volume 2 NAPCO Security Group...
  • Page 31 Address 5892 determines the maximum time allowed for the double swipe (x100ms). Address 5893 determines the door unlock time, in seconds, after a successful entry.  1. Select timeout (1-255).  2. Enter in corresponding address locations above and right. Press to save. NAPCO Gemini C-Series Control Panel Programming Instructions--Volume 2 NAPCO Security Group...
  • Page 32 Select the Emergency Free Access ADDRESS 7978 Zone Number (1-255) and enter corre- Emergency Free Access sponding address location at right. Zone Number  Press to save. [Default = 000] NAPCO Gemini C-Series Control Panel Programming Instructions--Volume 2 NAPCO Security Group...
  • Page 33 The display will re-appear when an exit/entry door is faulted, causing an entry time delay display, or if a valid user code is entered at the keypad while the system is armed. NAPCO Gemini C-Series Control Panel Programming Instructions--Volume 2 NAPCO Security Group...
  • Page 34 Area number (1-8) in the above table.  Enter the corresponding Area number in each the address location, in Binary (Bit) Format.  Press to save. NOTE: See Direct Address Programming Example on page 72. NAPCO Gemini C-Series Control Panel Programming Instructions--Volume 2 NAPCO Security Group...
  • Page 35 Area number (1-8) in the above table.  Enter the corresponding Area number in each the address location, in Binary (Bit) Format.  Press to save. NOTE: See Direct Address Programming Example on page 72. NAPCO Gemini C-Series Control Panel Programming Instructions--Volume 2 NAPCO Security Group...
  • Page 36 EZM Group 59 EZM Group 60 ZONES 233-236 ZONES 237-240 ZONES 225-228 ZONES 229-232 ZONES 241-244 ZONES 245-248 ADDRESS 5636 ADDRESS 5637 ADDRESS 5634 ADDRESS 5635 ADDRESS 5638 ADDRESS 5639 Continued NAPCO Gemini C-Series Control Panel Programming Instructions--Volume 2 NAPCO Security Group...
  • Page 37 2. Enter the corresponding Area number in each the address location, in Binary (Bit) Format. NOTE: See Direct Address Programming Example on page 72.  3. Press to save. NAPCO Gemini C-Series Control Panel Programming Instructions--Volume 2 NAPCO Security Group...
  • Page 38 2. Enter the corresponding Area number in each the address location, in Binary (Bit) Format. NOTE: See Direct Address Programming Example on page 72.  3. Press to save. NOTE: Dark shaded data value box shows option not available. NAPCO Gemini C-Series Control Panel Programming Instructions--Volume 2 NAPCO Security Group...
  • Page 39 2. Enter the corresponding Area number in each the address location, in Binary (Bit) Format. NOTE: See Direct Address Programming Example on page 72.  3. Press to save. NAPCO Gemini C-Series Control Panel Programming Instructions--Volume 2 NAPCO Security Group...
  • Page 40 NOTE: These timers apply only to Supervised RF 2550 min. = 42 350 min. Transmitters (see RF Transmitters in Easy Menu Hr., 30 min. 360 min. Driven Mode Programming). 370 min. NAPCO Gemini C-Series Control Panel Programming Instructions--Volume 2 NAPCO Security Group...
  • Page 41 Access address 8179, then press the button. Data entry is not allowed. Note: Some features (schedules, language configuration) can only be re- programmed with the Downloading Software. NAPCO Gemini C-Series Control Panel Programming Instructions--Volume 2 NAPCO Security Group...
  • Page 42 Coded Alarms By Zone ............101 Automatic Interior Bypass/Easy Exit (ADDRESS 5326) ..93 Coded Cadence 4 Cycles only ..........93 Auto-Reset After Burg Bell Timeout (ADDRESS 5323) ... 92 Codes (overview) ..............15 NAPCO Gemini C-Series Control Panel Programming Instructions--Volume 2 NAPCO Security Group...
  • Page 43 Disable Code Required For EZ Bypass (ADDRESS 5325) ..93 Enable GEMC-F8ZCPIM ............101 Disable Code Required For Func. Mode Lvl. 1 (ADDRESS 5325) Enable GEMC-Print (ADDRESS 7920) ........93 ....................93 Enable Housing Tamper ............101 NAPCO Gemini C-Series Control Panel Programming Instructions--Volume 2 NAPCO Security Group...
  • Page 44 Fire Supervision (Event ID Code) ..........32 Enable Multiple Ring Connection Method ........ 92 Fire Supervisory (Modem Code) ..........62 Enable Napco Proprietary Access Format (ADDRESS 5890) . 99 Fire Tamper EZM (Event ID Code) .......... 32 Enable No EOLR Zones (Easy Menu) ........31 Fire User Code (add new) ............
  • Page 45 Pull Station Alarm (Modem Code) ........... 62 Supervision Disabled NAC A-D (ADDRESS 5330) ....92 Pulse Burg Bell (Zone Option) ........... 79–91 Supervisory Alarm Auto Reset (ADDRESS 5325) ....93 NAPCO Gemini C-Series Control Panel Programming Instructions--Volume 2 NAPCO Security Group...
  • Page 46 User Program (Burglary User Option) ........34 Verification (Fire) (Zone Option) ........79–91 Warranty ................120 Water Flow1 Delay Time (ADDRESS 5313) ......55 Waterflow (Fire) (Zone Option) .......... 79–91 NAPCO Gemini C-Series Control Panel Programming Instructions--Volume 2 NAPCO Security Group...
  • Page 47 5322 ........Status Report (Auto - Byp. Zones On Clos.) ..................92 5323 ........Access Control On Burg Module PGM1 Output ................. 92 5323 ........Auto Output Test Upon Arming ......................92 NAPCO Gemini C-Series Control Panel Programming Instructions--Volume 2 NAPCO Security Group...
  • Page 48 5890 ........Enable Card Presentation Beep and Green LED Flash ..............99 5890 ........Enable Facility Code .......................... 99 5890 ........Enable Napco Proprietary Access Format ..................99 5890 ........Enable Printing of Access Events ...................... 99 5890 ........Enable Two - Swipe Arming ....................... 99 5892 ........
  • Page 49 8174 ........System Delays & Timeouts ........................ 55 8175 ........Answer on Ring Number ........................58 8177 ........Clear Dealer Program ........................109 8179 ........Cold Start ............................109 NAPCO Gemini C-Series Control Panel Programming Instructions--Volume 2 NAPCO Security Group...
  • Page 50 Page 118 Programming Instructions, Volume 2 NOTES NAPCO Gemini C-Series Control Panel Programming Instructions--Volume 2 NAPCO Security Group...
  • Page 51 Programming Instructions, Volume 2 Page 119 NOTES NAPCO Gemini C-Series Control Panel Programming Instructions--Volume 2 NAPCO Security Group...
  • Page 52: Napco Limited Warranty

    In no event shall NAPCO be liable for an amount in NAPCO will, within said period, at its option, repair or excess of NAPCO's original selling price of the...