Electric texture sprayer with compressor, tex-spray compact, 100 psi 7 bar maximum working pressure, with 1 or 3/4 in. fluid hose, 3/8 in. air hose, and gun (24 pages)
120 vac, 18a airless paint sprayer a series 3000 psi (210 bar) maximum working pressure (29 pages)
Summary of Contents for Graco 231-830
Page 1
Model 231–830, Series A Complete sprayer with hose, Contractor FTx-E gun, RAC IV DripLess Tip Guard and SwitchTip 7291C GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441 COPYRIGHT 1997, GRACO INC. Graco Inc. is registered to I.S. EN ISO 9001...
WARNING INJECTION HAZARD Spray from the gun, leaks or ruptured components can inject fluid into your body and cause extremely serious injury, including the need for amputation. Fluid splashed in the eyes or on the skin can also cause serious injury. Fluid injected into the skin is a serious injury.
Page 4
Do not use hoses to pull equipment. Route hoses away from traffic areas, sharp edges, moving parts, and hot surfaces. Do not expose Graco hoses to temperatures above 82 C (180 F) or below –40 C (–40 F). Do not lift pressurized equipment.
Component Identification and Function 7291C Fig. 1 Motor DC motor, 110 VAC, 50 Hz, 10A, 1 phase Drive Assembly Transfers power from DC motor to the displacement pump Pressure Adjusting Knob Controls fluid outlet pressure ON/OFF Switch Power switch that controls 110 VAC power to sprayer Fluid Outlet Hose and spray gun is connected here Displacement Pump...
Setup 3. Fill the wet–cup (102). Pry off the wet-cup seal. WARNING Fill the cup 1/3 full with Graco Throat Seal Liquid (TSL), supplied. Install the wet-cup seal. If you supply your own hoses and spray gun, be sure the hoses are electrically conductive, that the 4.
Page 7
Setup 1/4 npsm(m) fluid outlet Do not install any shutoff device here Rotate clockwise to increase pressure Shown in closed or spray position Fill 1/3 full with TSL 7291C Fig. 4...
Operation How to use the gun trigger safety Open or drain, position When engaged, the gun safety latch prevents the gun Closed, or spray position from accidental triggering. See Fig. 5. WARNING INJECTION HAZARD If the gun still sprays when the gun trigger safety is locked, repair the gun.
Page 9
Operation How to use the RAC IV tip guard. WARNING INJECTION HAZARD To reduce the risk of serious injury, whenever you are instructed to relieve pressure, follow the Pressure Relief Tip handle shown in Procedure on page 10. spraying position. Turn handle 180 , The tip guard alerts you to the risk and helps prevent trigger gun to clear clog...
Startup NOTE: Refer to Fig. 4 and the other figures referenced WARNING in the text as you start the sprayer. INJECTION HAZARD 1. Open the pressure drain valve (42). See Fig. 9. The system pressure must be manually relieved to prevent the system from 2.
Page 11
Startup b. If more coverage is needed, use a larger tip WARNING rather than increasing the pressure. FIRE AND EXPLOSION HAZARD To reduce the risk of static sparking and c. Adjust the direction of the spray pattern. See splashing when priming or flushing the Fig.
Shutdown and Care 8. Coil the hose and hang it on a hose rack when WARNING storing it, even for overnight, to help protect the hose from kinking, abrasion, coupling damage, etc. INJECTION HAZARD To reduce the risk of serious injury, WARNING whenever you are instructed to relieve pressure, follow the Pressure Relief...
Flushing When to Flush 3. Pour one-half gallon (2 liters) of compatible solvent into a grounded metal flushing pail. Put the suction 1. Before using a new sprayer: flush out the oil hose in the pail. which was left in to protect pump parts. 4.
Troubleshooting WARNING INJECTION HAZARD To reduce the risk of serious injury, whenever you are instructed to relieve pressure, follow the Pres- sure Relief Procedure on page 10. Basic Problem Solving Check everything in the troubleshooting table before disassembling the sprayer. TYPE OF PROBLEM WHAT TO CHECK WHAT TO DO...
Page 15
Basic Problem Solving TYPE OF PROBLEM WHAT TO CHECK WHAT TO DO If check is OK, go to next check When check is not OK, refer to this column Electrical 5. Check motor armature commutator for burn 5. Remove motor and have motor shop (continued) spots, gouges and extreme roughness.
Page 16
Intermediate Problem Solving TYPE OF PROBLEM WHAT TO CHECK WHAT TO DO If check is OK, go to next check When check is not OK, refer to this column Low output 3. Release gun trigger. Observe resting position of 3. If pump consistently comes to rest with (continued) pump rod (107).
Page 17
Intermediate Problem Solving TYPE OF PROBLEM WHAT TO CHECK WHAT TO DO When check is not OK, refer to this column If check is OK, go to next check 1. Spray tip worn beyond sprayer pressure capa- 1. Replace spray tip. Spray Pattern Variations bility.
Motor Test WARNING INJECTION HAZARD To reduce the risk of serious injury, whenever you are instructed to relieve pressure, follow the Pressure Relief Procedure on page 10. For checking armature, motor winding and brush electrical continuity. Setup Remove the drive housing. See page 25. This is to ensure that any resistance you notice in the armature test is due to the motor and not to worn gears in the drive housing.
General Repair Information WARNING WARNING INJECTION HAZARD HOT SURFACE HAZARD To reduce the risk of serious injury, During operation, the motor and drive whenever you are instructed to relieve housing become very hot and could burn pressure, follow the Pressure Relief your skin if touched.
Motor Brushes NOTE: Replace brushes when worn to about 0.5 in. Motor lead; do not disconnect (12.5 mm). Always check both brushes. Brush Repair Minimum 0.5” (12.5 mm) Kit 236–967, which includes spring clip 112–766, is available for motors manufactured by Pacific Scientific. Included in Brush Repair Kit 236–967 NOTE: Replacement brushes may last only half as...
Page 21
Motor Brushes 9. Test the brushes. WARNING a. Remove the pump connecting rod pin (17). See Fig. 19, page 22. MOVING PARTS HAZARD Do not touch the brushes, leads, springs b. With the sprayer OFF, turn the pressure con- or brush holders while the sprayer is trol knob fully counterclockwise to minimum plugged in to reduce the risk of electric pressure.
Page 22
(121*). For the best leakage, but no tighter. Fill the packing nut/wet-cup results, use all the new parts in the kit, even if the old 1/3 full with Graco TSL. Push the plug (123) into ones still look good. the wet-cup.
Page 23
Motor 9. Align the new motor with the base and reinstall the WARNING screws (46). INJECTION HAZARD 10. Assemble the drive housing to the motor. Follow To reduce the risk of serious injury, steps 8 to 10 on page 25. whenever you are instructed to relieve 11.
Motor Start Board On/Off Switch NOTE: See Fig. 23 for this procedure. WARNING 1. Relieve pressure. 2. Remove the junction box screws (56) and lower INJECTION HAZARD the junction box (59). To reduce the risk of serious injury, whenever you are instructed to relieve 3.
Drive Housing, Connecting Rod, Crankshaft WARNING CAUTION INJECTION HAZARD Do not allow the gear (16) to fall; it may stay at- To reduce the risk of serious injury, tached to the drive housing or to the motor. whenever you are instructed to relieve Do not lose the thrust balls (11a or 4a) or let them fall pressure, follow the Pressure Relief between the gears, which will damage the drive hous-...
Page 26
Drive Housing, Connecting Rod, Crankshaft REF A Torque to 21 in–lb (2.4 N.m) Quantity of three Quantity of one Apply a total of 3 fl. oz.(89 cc) of grease to gears. Note: Filter not shown 02815 Fig. 25...
Pressure Control 7. Loosely install the screws (63) and then torque WARNING them to 21 in–lb (2.4 N.m). INJECTION HAZARD 8. Install the front cover (13). Connect the harness To reduce the risk of serious injury, (A) to the motor start board (47). whenever you are instructed to relieve 9.
Pressure Transducer 6. Align the holes in the transducer as shown by the WARNING arrows in Fig. 27. INJECTION HAZARD 7. Install the displacement pump. See page 22. To reduce the risk of serious injury, whenever you are instructed to relieve pressure, follow the Pressure Relief Procedure on page 10.
Sprayer Parts List Model 231–830, Series A Part No. Description Part No. Description 111–700 GRIP, handle 187–962 GASKET, filter inlet MOTOR KIT Includes 4a to 4e 237–458 111–826 SWITCH, ON/OFF 100–069 . BALL, SST, 1/4” dia. 105–658 LOCKING RING 111–616 .
Graco distributor to the original purchaser for use. With the exception of any special extended or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective.