Summary of Contents for Raymarine SeaTalk Joystick
Page 1
Raymarine dealer for assistance. Warranty To register your new Raymarine product, please take a few minutes to fill out the warranty card. It is important that you complete the owner information and return the card to us to receive full warranty benefits.
EMC Conformance All Raymarine equipment and accessories are designed to the best industry standards for use in the recreational marine environment. Their design and manufacture conforms to the appropriate Electromagnetic Compatibility (EMC) standards, but correct installation is required to ensure that performance is not compromised.
The WEEE Directive requires the recycling of waste electrical and electronic equipment. Whilst the WEEE Directive does not apply to some of Raymarine's products, we support its policy and ask you to be aware of how to dispose of this product.
Basic operation To engage joystick control, press the control button (located on top of the lever) once. The autopilot will then display MANUAL (ST6001 controllers) or PWR STEER (ST7001 & 8001 controllers) along with the current heading.
Page 5
Raymarine SeaTalk Joystick Proportional mode - applying port rudder Small Helm Angle Large Helm Angle Proportional mode - applying starboard rudder Small Helm Angle Large Helm Angle PWR STEER PWR STEER PWR STEER PWR STEER D6424-1 D6425-1...
Page 6
Bang-Bang mode Bang-Bang (drive left – drive right) mode applies continuous rudder drive in the direction of joystick movement. To improve control, the speed of rudder movement changes with the angle of the lever: for maximum speed push the lever hardover. If the lever is returned to the center position the rudder will remain in its current position.
Page 7
Raymarine SeaTalk Joystick 1.2 Installation Overview The diagram below gives an overview of how the joystick can be connected to your SeaTalk system. SmartPilot Computer Screen Yellow Screen Yellow Joystick Pod SeaTalk SeaTalk To SeaTalk 1m Joystick compatible device interface cable...
Page 8
3. Peel off the protective paper from the rear of the weather gasket and fix to the joystick. 4. Secure the joystick with the thumb nuts provided. 5. Plug in the interface cable to the base of the joystick D6414-1...
Page 9
The Joystick pod must be positioned in a dry location where: • It is protected against physical damage. • Is within reach of the joystick interface cable (less than 0.9m from joystick) • It is at least 9 in (230 mm) from a compass.
Page 10
Step 3 - Wiring the Joystick pod The Pod connectors are color-coded, so ensure that each wire is connected to the correspondingly-colored connector. Make the connections as shown below. Once complete, replace the Pod cover. 1 Fit SeaTalk cable 3 Press SeaTalk cable into the cable...
Page 11
Raymarine SeaTalk Joystick Step 4 - Connecting to your SeaTalk network The joystick is supplied with 6 ft. (2 m) of cable which should be connected to the SeaTalk network as shown 1.3 Setting up your Joystick CAUTION: Ensure that your autopilot is fully calibrated and that rudder alignment checks have been performed.
Page 13
Raymarine SeaTalk Joystick Template SeaTalk Joystick Mounting Template Forward Drill 5 mm (3/16 in) diameter hole (4 positions) Remove shaded areas only 76 mm (3 in) D6412-1...
For any Raymarine product or system that (i) has been installed on your vessel by a Raymarine-certified service agent or by a Raymarine OEM, and (ii) has a MSRP equal to or greater than USD $2,500, you are eligible to receive warranty service by a Raymarine certified service agent on-board your vessel (‘On Board Warranty Service’) for a period of 12...
Other conditions This Warranty is fully transferable provided that you furnish the original proof of purchase to Raymarine or, in the case of On Board Warranty Service, to a Raymarine-certified service agent. This Warranty is void if the label bearing the serial number has been removed or defaced.
2 years (24 months), subject to the limits contained in this warranty document. In the case of a product installed, by a Raymarine certified OEM installer, on a new boat prior to the sale of the boat to a customer, the 2-year period will begin on the date of the sale of the boat to the customer.
Raymarine Service Agent) at no further cost and promptly returned to the customer. 3.3 In cases where the customer is making a warranty claim and the product has been installed by a Raymarine certified installer, (boat builder, installer, dealer etc.) i.e. Onboard warranty, the nearest Raymarine approved service agent should be contacted and onboard service requested (which will be subject to the limits referred to in paragraph 4.12 below).
Page 19
Raymarine World Wide Warranty 4.10 If repairs are necessary under the warranty, the affected product must be forwarded to a Raymarine facility or a Raymarine approved service agent, at the owner’s expense. 4.11 The Raymarine warranty does not cover any differences in material, coloring or size between those alluded to in corporate advertising, literature or published on the internet, which are not specifically objected to at the time of delivery.
Page 20
North and South America Raymarine Technical Support 1-800-539-5539 or, +1 603-881-5200 Product Repair and Service Raymarine Product Repair Center 21 Manchester Street, Merrimack, NH 03054-4801 Help us to help you To allow us to respond to your needs faster, please quote the Equipment type,...