Related Manuals for Epcos CeraDiodes
Summary of Contents for Epcos CeraDiodes
- Page 1 CeraDiodes High-speed series Series/Type: Date: November 2010 © EPCOS AG 2010. Reproduction, publication and dissemination of this publication, enclosures hereto and the information contained therein without EPCOS' prior express consent is prohibited.
- Page 2 CeraDiodes High-speed series Features Single chip Very low capacitance values 0.6 up to 10 pF ESD protection to IEC 61000-4-2, level 4 Bidirectional ESD protection in one component No change in ESD protection performance at temperatures up to 85 °C (temperature derating)
- Page 3 CeraDiodes High-speed series Electrical specifications and ordering codes = 85 °C) and characteristics (T = 25 °C) Maximum ratings (T op,max Type Ordering code DC,max BR,min clamp,max (1 mA) (1 A) (1 MHz, 1 V) (1 MHz, 1 V) Array, 2/4 data + 1 supply, 0506, SOT-666...
- Page 4 CeraDiodes High-speed series Dimensional drawings Single device Dimensions in mm Case (inch) 0201 0402 0603 1003 size (mm) 0603 1005 1608 2508 Min. Max. Min. Max. Min. Max. Min. Max. 0.57 0.63 0.85 1.15 1.45 1.75 2.34 2.74 0.27 0.33 0.4 0.27 0.33 0.4...
- Page 5 CeraDiodes High-speed series Recommended solder pads Single device Dimensions in mm Case size (inch) 0201 0402 0603 1003 (mm) 0603 1005 1608 2508 0.25 1.45 Array devices 4-fold array 2/4 data + 1 supply Dimensions in mm Case size (inch)
- Page 6 CeraDiodes High-speed series Pin configurations Single device Description I/O line Array devices 4-fold array Description I/O line 1 I/O line 2 I/O line 3 I/O line 4 2/4 data + 1 supply Description I/O line 1 I/O line 2 I/O line 3...
- Page 7 CeraDiodes High-speed series Termination Single device Array device Please read Cautions and warnings and Page 7 of 22 Important notes at the end of this document.
- Page 8 CeraDiodes High-speed series Delivery mode EIA case size Taping Reel size Packing unit Type Ordering code pcs. 0201 Cardboard 15000 CDS1C05GTH B72440D0050H060 0402 Cardboard 10000 CDS2C05HDMI1 B72590D0050H160 0402 Cardboard 10000 CDS2C05HDMI2 B72590D0050H260 0402 Cardboard 10000 CDS2C15GTH B72590D0150H060 0402 Cardboard 10000...
- Page 9 CeraDiodes High-speed series Taping and packing for chip and array CeraDiodes Cardboard tape (taping to IEC 60286-3) Dimensions in mm 0402 0603 1003 0508 Tolerance Case size (inch) 0201 0603 1005 1608 2508 1220 (mm) 0.38 ±0.05 0.6 ±0.2 Compartment width 0.95...
- Page 10 CeraDiodes High-speed series Blister tape (taping to IEC 60286-3) Dimensions in mm 0506 0612 1012 Tolerance Case size (inch) 1216 1632 2532 (mm) ±0.2 Compartment width ±0.2 Compartment length Compartment height max. Sprocket hole diameter +0.1/ Compartment hole diameter min.
- Page 11 CeraDiodes High-speed series Reel packing Dimensions in mm Dimensions Tolerance Dimensions Tolerance ±2 Reel diameter +0/ –3 Reel width (inside) +1.5/ –0 +1.5/ –0 Reel width (outside) 14.4 max. 14.4 max. Package: 8-mm tape Reel material: Plastic Packing units ∅ 180-mm reel ∅...
- Page 12 CeraDiodes High-speed series Soldering directions Reflow soldering temperature profile Recommended temperature characteristic for reflow soldering following JEDEC J-STD-020D Profile feature Sn-Pb eutectic assembly Pb-free assembly Preheat and soak 100 °C 150 °C - Temperature min smin 150 °C 200 °C...
- Page 13 CeraDiodes High-speed series Soldering guidelines The use of mild, non-activated fluxes for soldering is recommended, as well as proper cleaning of the PCB. The components are suitable for reflow soldering to JEDEC J-STD-020D. Solder joint profiles / solder quantity Cement quantity The component is fixed onto the circuit board with cement prior to soldering.
- Page 14 CeraDiodes High-speed series 3.3.1 Solder joint profiles for nickel barrier termination Good and poor solder joints caused by amount of solder in infrared reflow soldering Please read Cautions and warnings and Page 14 of 22 Important notes at the end of this document.
- Page 15 CeraDiodes High-speed series Solderability tests Test Standard Test conditions / Test conditions / Criteria / test results Sn-Pb soldering Pb-free soldering Wettability Immersion in Immersion in Covering of 95% 60068-2-58 60/40 SnPb solder Sn96.5Ag3.0Cu0.5 of end termination, using non-activated solder using non- or checked by visual flux at 215 ±3 °C for...
- Page 16 CeraDiodes High-speed series Notes for proper soldering Preheating and cooling The average ramp-up rate must not exceed 3 °C/s. The cooling rate must not exceed 8 °C/s. Repair / rework Manual soldering with a soldering iron must be avoided, hot-air methods are recommended for making repairs.
- Page 17 Avoid manual soldering with a soldering iron. Wave soldering must not be applied for CeraDiodes designated for reflow soldering only. Keep to the recommended down-cooling rate. Standards...
- Page 18 (Reverse) current @ maximum reverse RM,max stand-off voltage, working voltage, operating voltage - *) Forward voltage *) Not applicable due to bidirectional characteristics of CeraDiodes Please read Cautions and warnings and Page 18 of 22 Important notes at the end of this document.
- Page 19 Do not use CeraDiodes in applications requiring a very high level of op- erational safety and especially when the malfunction or failure of a passive electronic compo- nent could endanger human life or health (e.g.
- Page 20 Storage conditions in original packaging: temperature -25 to +45°C, relative humidity ≤75% an- nual average, maximum 95%, dew precipitation is inadmissible. Do not store CeraDiodes where they are exposed to heat or direct sunlight. Otherwise the packaging material may be deformed or CeraDiodes may stick together, causing problems dur- ing mounting.
- Page 21 EPCOS CeraDiodes are not suitable for switching applications or voltage stabilization where static power dissipation is required. CeraDiodes are designed for ESD protection only. This listing does not claim to be complete, it merely reflects the experience of EPCOS AG. Please read Cautions and warnings and Page 21 of 22...
- Page 22 For these reasons, it is always ultimately incum- bent on the customer to check and decide whether an EPCOS product with the properties de- scribed in the product specification is suitable for use in a particular customer application.
Need help?
Do you have a question about the CeraDiodes and is the answer not in the manual?
Questions and answers