Table of Contents
Advertisement
Quick Links
IMPORTANT WARNING!!
PLEASE ENSURE THAT THE RECOMMENDED HEATER TANK UNIT (U.1998) AND FILTER KIT (U.1106)IS
USED.
TO AVOID PRESSURISED BOILING WATER AND TO COMPLY WITH US REGULATIONS THIS IS AN OPEN
VENTED PRODUCT.
DO NOT PLUG IN THE UNIT UNTIL ALL WATER CONNECTIONS HAVE BEEN MADE AND THE TANK HAS
FILLED COMPLETELY THEN FLUSHED TO REMOVE AIR.
*IMPORTANT!! ENSURE A PRESSURE REDUCING VALVE (PRV) IS USED IN-LINE WITH COLD INLET AND
IDEALLY SET TO 43.5PSI (3BAR). FAILURE TO DO SO MAY RESULT IN REDUCED PRODUCT PERFORMANCE.*
INSTANT HOT WATER TEMPERATURES CAN REACH 210°F. THE FAUCET IS DESIGNED WITH FEATURES
TO MINIMISE RISK AND POTENTIAL INJURY; TWO ACTION OPERATION, SPRING BACK VALVE AND
DELAYED DELIVERY; BUT SHOULD BE OPERATED OR SUPERVISED BY A RESPONSIBLE ADULT.
PLEASE READ AND FULLY UNDERSTAND THE HEATER TANK INSTRUCTIONS BEFORE USE.
MINI INSTANT HOT DISPENSERS
U.1323: AQUITAINE
NOTE: Diagram shows faucet
set up with u.1998 (heater
tank) and u.1106 (filter).
9.28749
Max Temp:
For Mains: 185°F
Recommended
Working Pressures:
Min 22psi
Max 72psi
*IMPORTANT!! ENSURE A PRESSURE REDUCING VALVE (PRV) IS USED IN-LINE
WITH COLD INLET AND IDEALLY SET TO 43.5PSI (3BAR). FAILURE TO DO SO MAY
RESULT IN REDUCED PRODUCT PERFORMANCE.**
Issue 1
Registration -
www.rohlhome.com/filtration-registration.aspx,
complete the registration card (postage paid) or
phone 1-800-777-9762 to register your product
U.1347: Mimas
U.1307: Parthian
G3/8"
OUT TO FILTER
FOR HEATER TANK
Please visit
1 1/7"
O
BASE RING
1 1/4"
O
HOLE
FLOW REGULATOR
TO BE FITTED TO
COLD INLET 9/16"-24
O
5 I.D
SILICONE TUBE
FROM TANK
.
Advertisement
Table of Contents
Related Manuals for Perrin & Rowe MIMAS U.1347
Summary of Contents for Perrin & Rowe MIMAS U.1347
- Page 1 id damaging the IMPORTANT WARNING!! uct for all warranty PLEASE ENSURE THAT THE RECOMMENDED HEATER TANK UNIT (U.1998) AND FILTER KIT (U.1106)IS USED. TO AVOID PRESSURISED BOILING WATER AND TO COMPLY WITH US REGULATIONS THIS IS AN OPEN VENTED PRODUCT. DO NOT PLUG IN THE UNIT UNTIL ALL WATER CONNECTIONS HAVE BEEN MADE AND THE TANK HAS FILLED COMPLETELY THEN FLUSHED TO REMOVE AIR.
- Page 2 The Mini Hot Dispensers Collection • • Installation & User Guide Congratulations on the purchase of your Perrin and Rowe Kitchen Product. Correctly installed and with sensible care, this product will give you many years of trouble free service. IMPORTANT INFORMATION Before you proceed...
- Page 3 ct. Correctly installed Connections to the filter (U.1106) and heater tank U.1998: ree service. (See separate filter guide and heater tank installation for further installation instructions) • Mount the filter housing in an accessible location using lumber to install this either screws in the bracket or the adhesive pad, ensuring the AVOID TRAPPING mounting area is clean by using the wipe provided.
- Page 4 BEFORE USE • Carefully check the installation for leaks. • If further building work is to be carried out in the vicinity, cover the mixer tap to avoid damaging the finish. • Please ensure that the installation complies with the local plumbing codes. ROHL WARRANTY POLICY All products supplied by ROHL carry warranties against manufacturing defects.
- Page 5 Electronic Instant Hot Water Appliance Installation, Operation and Care Instructions Please read these instructions fully before commencing the installation and operation of the Electronic Instant Hot Water Appliance...
-
Page 6: What You Need To Know Before You Start
We are delighted that you have chosen the electronic instant hot water appliance to compli- ment your instant hot water Dispenser. This unique electronic instant hot water appliance will save you time and effort when requiring near boiling water for making tea and coffee and we are sure you will discover many new uses each day. -
Page 7: Components Included
SAFETY INSTRUCTIONS PLEASE READ BEFORE YOU START The alert symbols displayed on the right point to important safety information to make you aware of potential hazards that can cause serious injury or death. Please pay special attention to the infor- mation following these warning alerts. -
Page 8: Important Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS PLEASE READ ALL INSTRUCTIONS CAREFULLY When using all electrical appliances, basic safety precautions should always be followed including the information below: To protect against electrical shock, do not place cord, plugs or unit near or in water or other liquids and do not operate the electronic instant hot water appliance controls or power socket with wet hands. -
Page 9: Installation Requirements
INSTALLATION REQUIREMENTS Electrical Requirements A standard 120v electrical outlet is required under the sink. If possible, use a separate circuit dedicated to your Hot Tank. It is recommended that a separate circuit serving only your electronic instant hot water appliance be provided or use an outlet that can be turned on/off by a switch. -
Page 10: Installation
PREPERATION FOR INSTALLATION Unlike other household hot water appliances, this electronic instant hot water appliance is Non Pressurised for safety reasons. For this electronic instant hot water appliance, the Instant Hot Dispenser is placed before the electronic instant hot water appliance, creating an “open vent”... - Page 11 INSTALLATION CONTINUED Step 2 – Connect Dispenser The electronic instant hot water appliance inlet connection is a 3/8” BSP male threaded connector. The outlet connector is a 3/8” BSP male thread connector. Check the connections type and size on the instant hot water Dispenser for the inlet and outlet connections.
- Page 12 INSTALLATION CONTINUED Step 4 – Electrical Connection Ensure that the installation area is dry and no water has spilled. Connect the plug to the power socket and turn on the power socket at the switch. The electronic instant hot water appliance display panel will now light up with the on / off button illuminated.
- Page 13 MAINTENANCE AND CARE INSTRUCTIONS CONTINUED Flushing the Instant Hot Water Tank It is recommended that the user flushes through the system completely by drawing off the instant hot water and allowing to reheat and repeating the process for a further 2 or 3 times to ensure the system is fully operational.
-
Page 14: Troubleshooting
TROUBLE SHOOTING PROBLEM POSSIBLE CAUSE WHAT TO DO Water and Steam is spitting Unit is boiling Turn instant hot water Dis- from the instant hot water penser handle on and release at Dispenser spout least 1 pint of water. Adjust the water temperature on the display to a lower setting. - Page 15 TROUBLE SHOOTING CONTINUED PROBLEM POSSIBLE CAUSE WHAT TO DO Slow Flow from the spout Water Filter may be The water filter must be clogged from impurities changed every 6 months or this in the inlet mains water will void the guarantee Water does not flow straight The electronic instant hot After a large volume of water...
- Page 16 Customer Services : ROHL LLC 3 Parker Irvine, California 92618-1605 Phone 800-777-9762 Guarantee Void Unless The Water Filter Is Replaced Every 6 Months Issue : PRV114112017 Rohl & Perrin & Rowe are Registered trade marks.
- Page 17 • • Instant Hot Tap • • CARTRIDGE REPLACMENT The filter cartridge in your instant hot tap system needs to be changed every six months in order to ensure the system works at its optimum performance. Changing the filter cartridge is a simple matter: 1.
- Page 18 • Instant Hot Tap • • • Filter Installation IT IS VERY IMPORTANT THAT BEFORE YOU START INSTALLING THIS Fixing Mounting Bracket FILTER SYSTEM YOU ENSURE YOU HAVE READ THE INSTALL GUIDES THAT CAME WITH THE TAP AND THE HEATER TANK. First you will need to remove the filter sump.