Daikin Perfera FTXS25K2V1B Installation Manual
Hide thumbs
Also See for Perfera FTXS25K2V1B:
- Service manual (462 pages) ,
- Operation manual (44 pages) ,
- Installation manual (18 pages)
Related Manuals for Daikin Perfera FTXS25K2V1B
Summary of Contents for Daikin Perfera FTXS25K2V1B
- Page 1 DAIKIN ROOM AIR CONDITIONER INSTALLATION MANUAL R410A Split Series MODELS FTXS20K2V1B FTXS20K3V1B FTXS25K2V1B FTXS25K3V1B CTXS15K2V1B CTXS15K3V1B CTXS35K2V1B CTXS35K3V1B ATXS20K2V1B ATXS20K3V1B ATXS25K2V1B ATXS25K3V1B...
- Page 2 3P390250-2...
- Page 3 3P363628–1...
- Page 4 3SB65451-1 3SB65451-1...
- Page 5 3SB65451-2...
-
Page 7: Safety Precautions
Safety Precautions • The precautions described herein are classified as WARNING and CAUTION. They both contain important information regarding safety. Be sure to observe all precautions without fail. • Meaning of WARNING and CAUTION notices WARNING..Failure to follow these instructions properly may result in personal injury or loss of life. CAUTION..Failure to observe these instructions properly may result in property damage or personal injury, which may be serious depending on the circumstances. -
Page 8: Choosing An Installation Site
• This appliance is intended to be used by expert or trained users in shops, in light industry and on farms, or for commercial and household use by lay persons. • Sound pressure level is less than 70 dB(A). Accessories –... -
Page 9: Preparation Before Installation
Preparation before Installation Removing and installing front panel • Removal method 1) Place your fingers in the indentations on the main unit (one each on the left and right sides), and open the front panel until it stops. 2) Continue to open the front panel further while sliding the panel to the right and pulling it toward you in order to disengage the front panel shaft on the left side. -
Page 10: Indoor Unit Installation Drawings
Indoor Unit Installation Drawings How to attach the indoor unit Mounting Hook the claws of the bottom frame plate to the mounting plate. If the claws are difficult to hook, remove the front grille. Clip Mounting plate How to remove the indoor unit Push up the marked area (at the lower part of the front grille) to Bottom frame... -
Page 11: Indoor Unit Installation
Indoor Unit Installation Installing the mounting plate • The mounting plate should be installed on a wall which can support the weight of the indoor unit. 1) Temporarily secure the mounting plate to the wall, make sure that the panel is completely level, and mark the boring points on the wall. - Page 12 Indoor Unit Installation • Remove the pipe port cover as shown below. 1) Cut off the pipe port cover from inside the front grille using a copping saw. Apply the blade of the copping saw to the notch, and cut off the pipe port cover along the slit.
- Page 13 Indoor Unit Installation 3-2. Left-side, left-back, or left-bottom piping How to replace the drain plug and drain hose • Replacing onto the left side Drain hose attachment position 1) Remove the insulation fixing screw on the * The drain hose is on the back of the unit. right and remove the drain hose.
- Page 14 Indoor Unit Installation Wiring diagram Terminal strip Connection Connector Field wiring Black Orange Blue Brown White Green Yellow Notes Refer to the nameplate for power requirements. INDOOR Indoor OUTDOOR Outdoor TRANSMISSION CIRCUIT Transmission circuit INTELLIGENT EYE SENSOR Intelligent eye sensor WIRELESS REMOTE CONTROLLER Wireless remote controller SIGNAL RECEIVER...
- Page 15 Indoor Unit Installation Wiring 1) Strip wire ends (15mm). 2) Match wire colours with terminal numbers on indoor and outdoor unit’s terminal blocks and firmly screw wires to the corresponding terminals. 3) Connect the earth wires to the corresponding terminals. 4) Pull wires to make sure that they are securely latched up, then retain wires with wire retainer.
- Page 16 Indoor Unit Installation 5-5. Prepare the accessory (optional parts) [Figure 2]. 1) Remove the cover from the accessory (optional parts). 2) Insert the connection cord into connector “S21” (white) in the accessory (optional parts). 3) Route each of the connection cords through the cut-outs in the accessory, then reinstall the accessory cover in its original position.
-
Page 17: Refrigerant Piping Work
Indoor Unit Installation Drain piping The drain hose should be inclined downward. 1) Connect the drain hose, as described right. No trap is permitted. Do not put the end of the hose in water. 2) Remove the air filters and pour some water into the drain pan to check the water flows smoothly. - Page 18 Refrigerant Piping Work Refrigerant piping CAUTION • Use the flare nut fixed to the main unit. (To prevent cracking of the flare nut by aged deterioration.) • To prevent gas leakage, apply refrigeration oil only to the inner surface of the flare. (Use refrigeration oil for R410A.) •...
-
Page 19: Trial Operation And Testing
Trial Operation and Testing Trial operation and testing 1-1 Measure the supply voltage and make sure that it falls in the specified range. 1-2 Trial operation should be carried out in either cooling or heating mode. • In cooling mode, select the lowest programmable temperature; in heating mode, select the highest programmable temperature. - Page 20 3P363588-1B 2014.06...