Page 1 AM–10A 10 KILOWATT AM–6A 6 KILOWATT AM BROADCAST TRANSMITTERS July, 1999 IM No. 597–1113...
Page 2 WARRANTY ADJUSTMENT. Broadcast Electronics, Inc. warranty is included in the Terms and Conditions of Sale. In the event of a warranty claim, replacement or repair parts will be supplied F.O.B. factory. At the discretion of Broadcast Electronics, the customer may be required to return the defective part or equipment to Broadcast Electronics, Inc.
Page 3 WARNING OPERATING HAZARDS READ THIS SHEET AND OBSERVE ALL SAFETY PRECAUTIONS ALL PERSONS WHO WORK WITH OR ARE EXPOSED TO POWER TRANSISTORS MUST TAKE PRECAUTIONS TO PROTECT THEMSELVES AGAINST POSSIBLE SERIOUS BODILY INJURY. EXERCISE EXTREME CARE AROUND SUCH PRODUCTS. UNINFORMED OR CARELESS OPERATION OF THESE DEVICES CAN RESULT IN POOR PERFORMANCE, DAMAGE TO THE DEVICE OR PROPERTY, SERIOUS BODILY INJURY, AND POSSI- BLY DEATH.
Page 4 BROADCAST ELECTRONICS, INC. TRANSMITTER WARRANTY VOID NOTICE THE PRODUCT WARRANTY WILL BE VOID IF THE TRANSMITTER IS INSTALLED AT A SITE WITH INADEQUATE LIGHTNING PROTECTION AND A DEFECTIVE TRANSMISSION LINE SYSTEM. TO ENSURE THE TRANSMIT TER WARRANTY IS VALID FAILURE TO...
Page 5 BROADCAST ELECTRONICS, INC. NOTICE TO THE EQUIPMENT USER...
Page 6: Operating Hazards
WARNING WARNING OPERATING HAZARDS THE TRANSMITTER CONTAINS MULTIPLE CIRCUIT WARNING GROUNDS WITH HIGH AC AND DC POTENTIALS WITH RESPECT TO THE CABINET WHICH IS AT EARTH PO WARNING TENTIAL. DO NOT ENERGIZE THE TRANSMITTER WITH TEST EQUIPMENT CONNECTED TO THE TRANSMITTER OUTPUT NETWORK, RF POWER MOD ULE, RF COMBINER, OR POWER SUPPLY COMPO NENTS.
Page 8: Operation
PARAGRAPH PAGE NO. SECTION III OPERATION...
Page 9: Theory Of Operation
PARAGRAPH PAGE NO. SECTION IV THEORY OF OPERATION...
Page 10: Maintenance
PARAGRAPH PAGE NO. SECTION V MAINTENANCE SECTION VI PARTS LIST SECTION VII DRAWINGS TABLE DESCRIPTION PAGE NO.
Page 11 FIGURE DESCRIPTION PAGE NO.
Page 12 ™ ™ ™ ™ ™ ™...
Page 16 DESCRIPTION DESCRIPTION...
Page 17: Specification
TABLE 1-1. ELECTRICAL CHARACTERISTICS (Sheet 1 of 4) PARAMETER SPECIFICATION RF POWER OUTPUT OUTPUT POWER REGULATION RF CARRIER FREQUENCY RANGE RF OUTPUT IMPEDANCE OUTPUT CONNECTOR LOAD VSWR HARMONIC AND SPURIOUS SUPPRESSION CARRIER FREQUENCY ± ° ° ° ° STABILITY CARRIER SHIFT...
Page 18: Modulation Capability
TABLE 1-1. ELECTRICAL CHARACTERISTICS (Sheet 2 of 4) PARAMETER SPECIFICATION TYPE OF MODULATION OPERATING MODES MODULATION CAPABILITY MODULATION INPUT INDICATION AUDIO INPUT LEVEL ± AUDIO INPUT IMPEDANCE AUDIO FREQUENCY ± RESPONSE (MONOPHONIC) AUDIO HARMONIC DISTORTION INTERMODULATION DISTORTION (MONO)
Page 19 TABLE 1-1. ELECTRICAL CHARACTERISTICS (Sheet 3 of 4) PARAMETER SPECIFICATION CCIF INTERMODULATION DISTORTION (MONO) TRANSIENT INTERMODULATION DISTORTION (MONO) INCIDENTAL PHASE MODULATION (STEREOPHONIC) STEREO SEPARATION SQUAREWAVE OVERSHOOT SQUAREWAVE TILT NOISE AC INPUT VOLTAGE AC POWER CONSUMPTION...
Page 20 TABLE 1-1. ELECTRICAL CHARACTERISTICS (Sheet 4 of 4) PARAMETER SPECIFICATION OVERALL EFFICIENCY SAFETY METERING RF MONITORING PROVISIONS REMOTE INTERFACE TABLE 1-2. PHYSICAL AND ENVIRONMENTAL CHARACTERISTICS (Sheet 1 of 2) PARAMETER SPECIFICATION PHYSICAL DIMENSIONS WEIGHT CUBAGE...
Page 21 TABLE 1-2. PHYSICAL AND ENVIRONMENTAL CHARACTERISTICS (Sheet 2 of 2) PARAMETER SPECIFICATION ENVIRONMENTAL COOLING OPERATING TEMPERATURE ° ° ° ° OPERATING HUMIDITY MAXIMUM ALTITUDE...
Page 23 WARNING ENSURE NO PRIMARY POWER IS CONNECTED TO THE TRANSMITTER BEFORE PROCEEDING. WARNING...
Page 27 © COPYRIGHT 1997 BROADCAST ELECTRONICS, INC 597-1113-36 FIGURE 2-4. TRANSMITTER MOVING THE TRANSMITTER MAY BE DAMAGED CAUTION IF THE ECU CIRCUIT BOARDS ARE NOT SECURELY SEATED INTO THE CONNECTORS. CAUTION REMOVING OR INSTALLING AN RF POWER MODULE CAUTION WITH THE TRANSMITTER ENERGIZED MAY RESULT IN DAMAGE TO THE MODULE.
Page 29 THE TRANSMITTER MAY BE DAMAGED IF THE CAUTION POWER SUPPLY CONNECTORS ARE NOT SE CURELY SEATED INTO THE POWER SUPPLY CAUTION CIRCUIT BOARD RECEPTACLES. CAUTION TO PREVENT DAMAGE TO THE POWER SUP PLY CIRCUIT BOARD, ENSURE THE CIRCUIT CAUTION BOARD IS INSERTED INTO THE MOUNTING PINS AND THE CAPACITORS ON THE CIRCUIT SIDE OF THE BOARD ARE PLACED INTO THE CAUTION...
Page 35 TRANSMITTER WARNING ENSURE PRIMARY POWER IS DISCONNECTED BE FORE PROCEEDING. WARNING...
Page 38 ° ° WARNING ENSURE PRIMARY POWER IS DISCONNECTED BE FORE PROCEEDING. WARNING J1 EXTERNAL STEREO RF INPUT...
Page 41 External Interlock Input Interlock +5v WARNING ENSURE PRIMARY POWER IS DISCONNECTED BE FORE PROCEEDING. WARNING WARNING ENSURE AN EARTH GROUND CONDUCTOR IS SE CURELY CONNECTED TO THE TRANSMITTER AC WARNING GROUND LUG. AM-10A TRANSMITTER AC DIST. PANEL DESCRIPTION PART NUMBER...
Page 42 AM-6A TRANSMITTER AC DIST. PANEL DESCRIPTION PART NUMBER WARNING ENSURE PRIMARY POWER IS DISCONNECTED BE FORE PROCEEDING. WARNING WARNING ENSURE PRIMARY POWER IS DISCONNECTED BEFORE PROCEEDING. WARNING WARNING ENSURE AN EARTH GROUND CONDUCTOR IS SECURELY CONNECTED TO THE TRANSMITTER WARNING...
Page 47 THE TRANSMITTER SITE LIGHTNING PROTECTION CAUTION SYSTEM MUST BE INSPECTED AND IN PROPER CAUTION WORKING CONDITION FOR RELIABLE TRANSMIT TER OPERATION. WARNING DISCONNECT ALL TRANSMITTER PRIMARY POWER BEFORE PROCEEDING. WARNING...
Page 50 THE TRANSMISSION LINE AND ANTENNA MUST BE CAUTION INSPECTED AND IN PROPER WORKING CONDITION CAUTION FOR RELIABLE TRANSMITTER OPERATION. WARNING ENSURE PRIMARY POWER IS DISCONNECTED BE FORE PROCEEDING. WARNING...
Page 51 WARNING THE TRANSMITTER POWER SUPPLY OPERATES FROM A HIGH FLOATING GROUND POTENTIAL. WARNING NEVER OPERATE THE TRANSMITTER WITH THE REAR DOOR OPEN. FORWARD POWER REFLECTED POWER TUNING LOADING REFLECTED POWER WARNING DISCONNECT ALL TRANSMITTER PRIMARY POWER BEFORE PROCEEDING. WARNING FORWARD POWER HIGH FORWARD POWER...
Page 53 WARNING DISCONNECT ALL TRANSMITTER PRIMARY POWER BEFORE PROCEEDING. WARNING WARNING DISCONNECT ALL TRANSMITTER PRIMARY POWER BEFORE PROCEEDING. WARNING © COPYRIGHT 1997 BROADCAST ELECTRONICS, INC 597-1113-8 FIGURE 2-18. TEST EQUIPMENT CONNECTIONS, SEPARATION...
Page 55 WARNING DISCONNECT ALL TRANSMITTER PRIMARY POWER BEFORE PROCEEDING. WARNING...
Page 56 BLANK PAGE...
Page 58 TABLE 3-1. AM-10A/AM-6A CONTROLS AND INDICATORS (Sheet 1 of 2) INDEX NOMENCLATURE FUNCTION FORWARD POWER FORWARD POWER LOW/HIGH/OFF FORWARD POWER FORWARD POWER HIGH/LOW/OFF REFLECTED POWER REFLECTED POWER HIGH/LOW/VAC REFLECTED POWER REFLECTED POWER HIGH/LOW/VAC...
Page 61: Rf Power Module
TABLE 3-1. AM-10A/AM-6A CONTROLS AND INDICATORS (Sheet 2 of 2) INDEX NOMENCLATURE FUNCTION RF POWER MODULE POWER BLOCK LOAD TUNE TUNE LOAD AC ON/OFF POWER SUPPLY 1-2 POWER SUPPLY 3-4 POWER SUPPLY 5-6 POWER SUPPLY 7-8 POWER SUPPLY 9-10...
Page 62: Power Modules
TABLE 3-2. ECU CONTROLS AND INDICATORS (Sheet 1 of 5) INDEX NOMENCLATURE FUNCTION EXCITER POWER MODULES POWER SUPPLY ANTENNA VSWR...
Page 63 TABLE 3-2. ECU CONTROLS AND INDICATORS (Sheet 2 of 5) INDEX NOMENCLATURE FUNCTION POWER CONTROL POWER POWER POWER POWER...
Page 65 TABLE 3-2. ECU CONTROLS AND INDICATORS (Sheet 3 of 5) INDEX NOMENCLATURE FUNCTION RESET EXCITER MONITOR STEREO EXCITER MONITOR MODE EXCITER MONITOR LED L+R/L-R EXCITER MONITOR +/- POLARITY EXCITER MONITOR EXCITER MONITOR EXCITER MONITOR MODE POLARITY R/L-R L/L+R X10 EXCITER MONITOR MONO R/L-R R/L-R...
Page 66 TABLE 3-2. ECU CONTROLS AND INDICATORS (Sheet 4 of 5) INDEX NOMENCLATURE FUNCTION L/L+R L/L+R OVERTEMP ° ° FOLDBACK INTERLOCK REMOTE CONFLICT LIGHTNING...
Page 67 TABLE 3-2. ECU CONTROLS AND INDICATORS (Sheet 5 of 5) INDEX NOMENCLATURE FUNCTION...
Page 68 (Sheet 1 of 2) INDEX NOMENCLATURE FUNCTION PA 1 RF DRIVE PA 1 FAULT PA 2 RF DRIVE PA 2 FAULT MOD PWM DRIVE MOD POWER © COPYRIGHT 1997 BROADCAST ELECTRONICS, INC 597-1112-31 FIGURE 3-3. POWER MODULE CONTROLS AND INDICATORS...
Page 69 TABLE 3-3. POWER MODULE CONTROLS AND INDICATORS (Sheet 2 of 2) INDEX NOMENCLATURE FUNCTION MOD FAULT MOD FUSE MOD SAMPLE CAUTION WHEN AC POWER IS APPLIED TO THE TRANSMIT TER AND THE RF DRIVE AND PWM DRIVE INDICA CAUTION TORS ON RF POWER MODULES IN A POWER BLOCK ARE EXTINGUISHED, THE RF POWER MODULES MUST BE REMOVED FROM THE TRANSMITTER CHASSIS TO PREVENT DAMAGE TO THE MODULES.
Page 70 FORWARD REFLECTED FORWARD POWER FORWARD POWER HIGH HIGH HIGH FORWARD POWER FORWARD POWER REFLECTED POWER REFLECTED POWER HIGH HIGH HIGH REFLECTED POWER POWER POWER FORWARD REFLECTED POWER FORWARD REFLECTED...
Page 71 MONO TO PREVENT DAMAGE TO THE TRANSMITTER, EN CAUTION SURE THE TRANSMITTER PRIMARY POWER IS OPER CAUTION ATED TO OFF BEFORE REMOVING THE STEREO CIR CUIT BOARD. MONO STEREO MONO STEREO L/R/L+R/L-R MODE L+R/L-R EXCITER MONITOR POLARITY EXCITER MONITOR...
Page 72: Transmitter Monitor
EXCITER MONITOR L/L+R R/L-R RESET POWER SUPPLY FAULT RESET RESET ac ON/OFF RESET TRANSMITTER MONITOR...
Page 80: Power Supply
AM-10A POWER SUPPLY AC POWER SOURCE AM-6A POWER SUPPLY AC POWER SOURCE...
Page 85 CONTROLLER INDICATORS RF POWER MODULE INDICATORS...
Page 94 WARNING THE TRANSMITTER CONTAINS MULTIPLE CIRCUIT GROUNDS WITH HIGH AC AND DC POTENTIALS WITH RESPECT TO THE CABINET WHICH IS AT WARNING EARTH POTENTIAL. DO NOT ENERGIZE THE WARNING TRANSMITTER WITH TEST EQUIPMENT CON NECTED TO THE TRANSMITTER OUTPUT WARNING NETWORK, RF POWER MODULE, RF COMBINER, OR POWER SUPPLY COMPONENTS.
Page 95 WARNING NEVER OPEN THE EQUIPMENT UNLESS ALL TRANS MITTER PRIMARY POWER IS DISCONNECTED. EN SURE ALL TRANSMITTER PRIMARY POWER IS DIS WARNING CONNECTED BEFORE ATTEMPTING MAINTENANCE ON ANY AREA WITHIN THE TRANSMITTER.
Page 97 WARNING NEVER OPEN THE EQUIPMENT UNLESS ALL TRANS MITTER PRIMARY POWER IS DISCONNECTED. EN SURE ALL TRANSMITTER PRIMARY POWER IS DIS WARNING CONNECTED BEFORE ATTEMPTING MAINTENANCE ON ANY AREA WITHIN THE TRANSMITTER. WARNING NEVER OPEN THE EQUIPMENT UNLESS ALL TRANS MITTER PRIMARY POWER IS DISCONNECTED.
Page 98: Indicator Function
WARNING THE TRANSMITTER CONTAINS MULTIPLE CIRCUIT GROUNDS WITH HIGH AC AND DC POTENTIALS WITH RESPECT TO THE CABINET WHICH IS AT WARNING EARTH POTENTIAL. DO NOT ENERGIZE THE WARNING TRANSMITTER WITH TEST EQUIPMENT CON NECTED TO THE TRANSMITTER OUTPUT WARNING NETWORK, RF POWER MODULE, RF COMBINER, OR POWER SUPPLY COMPONENTS.
Page 99 TABLE 5-1. AM-10A INDICATORS (Sheet 2 of 4) ASSEMBLY INDICATOR FUNCTION ° °...
Page 100 TABLE 5-1. AM-10A INDICATORS (Sheet 3 of 4) ASSEMBLY INDICATOR FUNCTION...
Page 101 TABLE 5-1. AM-10A INDICATORS (Sheet 4 of 4) ASSEMBLY INDICATOR FUNCTION WHEN AC POWER IS APPLIED TO THE TRANSMIT CAUTION TER AND THE RF DRIVE AND PWM DRIVE INDICA CAUTION TORS ON RF POWER MODULES IN A POWER BLOCK ARE EXTINGUISHED, THE RF POWER MODULES MUST BE REMOVED FROM THE TRANSMITTER CHASSIS TO PREVENT DAMAGE TO THE MODULES.
Page 102 TABLE 5-2. AM-10A/AM-6A TROUBLESHOOTING (Sheet 1 of 5) SYMPTOM CIRCUITRY TO CHECK ±...
Page 103 TABLE 5-2. AM-10A/AM-6A TROUBLESHOOTING (Sheet 2 of 5) SYMPTOM CIRCUITRY TO CHECK...
Page 104 TABLE 5-2. AM-10A/AM-6A TROUBLESHOOTING (Sheet 3 of 5) SYMPTOM CIRCUITRY TO CHECK...
Page 105 TABLE 5-2. AM-10A/AM-6A TROUBLESHOOTING (Sheet 4 of 5) SYMPTOM CIRCUITRY TO CHECK...
Page 106 TABLE 5-2. AM-10A/AM-6A TROUBLESHOOTING (Sheet 5 of 5) SYMPTOM CIRCUITRY TO CHECK...
Page 107 WARNING MOST SOLVENTS WHICH WILL REMOVE ROSIN FLUX ARE VOLATILE AND TOXIC BY THEIR NATURE AND SHOULD BE USED ONLY IN SMALL AMOUNTS IN A WARNING WELL VENTILATED AREA, AWAY FROM FLAME SUCH WARNING AS FROM A SOLDERING IRON OR SMOKING MATERI ALS.
Page 117 TABLE 6-1. AM-10A/AM-6A REPLACEABLE PARTS LIST INDEX (Sheet 1 of 2) TABLE DESCRIPTION PART NO. PAGE...
Page 118 TABLE 6-1. AM-10A/AM-6A REPLACEABLE PARTS LIST INDEX (Sheet 2 of 2) TABLE DESCRIPTION PART NO. PAGE...
Page 119 TABLE 6-2. AM-10A TRANSMITTER, 3-PHASE/SINGLE-PHASE - 907-1010-001/-041/-011 REF. DES. DESCRIPTION PART NO. QTY. ± ± FOR 907-1010-001 ASSEMBLIES FOR 907-1010-041 ASSEMBLIES FOR 907-1010-011 ASSEMBLIES TABLE 6-3. AM-6A TRANSMITTER, 3-PHASE/SINGLE-PHASE - 907-6000/-030/-040 (Sheet 1 of 2) REF. DES. DESCRIPTION PART NO. QTY. ± ±...
Page 120 TABLE 6-3. AM-6A TRANSMITTER, 3-PHASE/SINGLE-PHASE - 907-6000/-030/-040 (Sheet 2 of 2) REF. DES. DESCRIPTION PART NO. QTY. FOR 907-6000-030 ASSEMBLIES FOR 907-6000-040 ASSEMBLIES FOR 907-6000-030/-040 ASSEMBLIES DELETE PARTS ADD PARTS TABLE 6-4. AM-10A RACK ASSEMBLY- 907-0110 REF. DES. DESCRIPTION PART NO.
Page 121 TABLE 6-6. AM-10A FAN ASSEMBLY - 380-7650-010 REF. DES. DESCRIPTION PART NO. QTY. TABLE 6-7. AM-6A FAN ASSEMBLY - 380-7650-006 REF. DES. DESCRIPTION PART NO. QTY. TABLE 6-8. INTERFACE CIRCUIT BOARD ASSEMBLY - 917-0306-003 REF. DES. DESCRIPTION PART NO. QTY.
Page 122 PART NO. QTY. ± ± ± ± ± TABLE 6-11. WIRE HARNESS MAIN AM TRANSMITTER, AM-10A - 947-0182 REF. DES. DESCRIPTION PART NO. QTY. TABLE 6-12. HARNESS, ADD-ON, AM-6A - 947-0190 (Sheet 1 of 2) REF. DES. DESCRIPTION PART NO. QTY.
Page 123 TABLE 6-13. AC DISTRIBUTION PANEL ASSEMBLY, AM-10A - 957-0021-001/-041/-011 REF. DES. DESCRIPTION PART NO. QTY. FOR 957-0021-001 ASSEMBLY FOR 957-0021-041 ASSEMBLY FOR 957-0021-011 ASSEMBLY TABLE 6-14. AC DISTRIBUTION PANEL ASSEMBLY, AM-6A - 957-0013-010/-030/-040 (Sheet 1 of 2) REF. DES. DESCRIPTION PART NO. QTY.
Page 124 TABLE 6-14. AC DISTRIBUTION PANEL ASSEMBLY, AM-6A - 957-0013-010/-030/-040 (Sheet 2 of 2) REF. DES. DESCRIPTION PART NO. QTY. FOR 957-0013-010 ASSEMBLY FOR 957-0013-030/957-0013-040 ASSEMBLY DELETE PARTS ADD PARTS FOR 957-0013-030 ASSEMBLY FOR 957-0013-040 ASSEMBLY TABLE 6-15. OPTICALLY COUPLED RELAY CIRCUIT BOARD ASSEMBLY - 919-0096-001 REF.
Page 125 TABLE 6-16. OPTICALLY COUPLED RELAY CIRCUIT BOARD ASSEMBLY - 919-0096 (Sheet 2 of 2) REF. DES. DESCRIPTION PART NO. QTY. ± ± ± ± ± ± ± TABLE 6-17. AC SAMPLE CIRCUIT BOARD ASSEMBLY - 917-0306-007 REF. DES. DESCRIPTION PART NO. QTY.
Page 126 TABLE 6-18. AC DISTRIBUTION HARNESS ASSEMBLY, AM-10A - 947-0185 REF. DES. DESCRIPTION PART NO. QTY. TABLE 6-19. AC DISTRIBUTION HARNESS ASSEMBLY, AM-6A - 947-0191 REF. DES. DESCRIPTION PART NO. QTY. TABLE 6-20. POWER BLOCK, SINGLE ASSEMBLY /DOUBLE ASSEMBLY, AM-10A- 957-0022-001/-002 REF.
Page 127 TABLE 6-22. POWER BLOCK, DOUBLE ASSEMBLY, AM-6A - 957-0022-062 REF. DES. DESCRIPTION PART NO. QTY. TABLE 6-23. POWER BLOCK MOTHERBOARD CIRCUIT BOARD ASSEMBLY - 917-0303 REF. DES. DESCRIPTION PART NO. QTY. ± TABLE 6-24. COMBINER CIRCUIT BOARD ASSEMBLY, AM-10A/AM-6A - 917-0321/-006 REF.
Page 128 REF. DES. DESCRIPTION PART NO. QTY. FOR 957-0031 ASSEMBLIES FOR 957-0031-010 ASSEMBLIES TABLE 6-26. ACCESSORY PARTS KIT, AM-6A - 957-0033 REF. DES. DESCRIPTION PART NO. QTY. TABLE 6-27. FREQUENCY DEPENDANT KIT, AM-10A, 522 - 650 KHZ - 957-0015-101 REF. DES.
Page 129 TABLE 6-28. FREQUENCY DEPENDANT KIT, AM-10A, 651 - 770 KHZ - 957-0015-102 REF. DES. DESCRIPTION PART NO. QTY. TABLE 6-29. FREQUENCY DEPENDANT KIT, AM-10A, 771 - 920 KHZ - 957-0015-103 REF. DES. DESCRIPTION PART NO. QTY. TABLE 6-30. FREQUENCY DEPENDANT KIT, AM-10A, 921 - 1080 KHZ - 957-0015-104 REF.
Page 130 TABLE 6-33. FREQUENCY DEPENDANT KIT, AM-10A, 1581 - 1700 KHZ - 957-0015-107 REF. DES. DESCRIPTION PART NO. QTY. TABLE 6-34. FREQUENCY DEPENDANT KIT, AM-6A, 522 - 650 KHZ - 957-0015-061 REF. DES. DESCRIPTION PART NO. QTY. TABLE 6-35. FREQUENCY DEPENDANT KIT, AM-6A, 651 - 770 KHZ - 957-0015-062 REF.
Page 131 TABLE 6-38. FREQUENCY DEPENDANT KIT, AM-6A, 1081 - 1300 KHZ - 957-0015-065 REF. DES. DESCRIPTION PART NO. QTY. TABLE 6-39. FREQUENCY DEPENDANT KIT, AM-6A, 1301 - 1580 KHZ - 957-0015-066 REF. DES. DESCRIPTION PART NO. QTY. TABLE 6-40. FREQUENCY DEPENDANT KIT, AM-10A, 1581 - 1700 KHZ - 957-0015-067 REF.
Page 132 TABLE 6-43. POWER BLOCK FREQUENCY DEPENDANT KIT, AM-10A, 771 - 920 KHZ - 957-1025-053 REF. DES. DESCRIPTION PART NO. QTY. TABLE 6-44. POWER BLOCK FREQUENCY DEPENDANT KIT, AM-10A, 921 - 1080 KHZ - 957-1025-054 REF. DES. DESCRIPTION PART NO. QTY. TABLE 6-45.
Page 133 TABLE 6-48. POWER BLOCK FREQUENCY DEPENDANT KIT, AM-6A, 522 - 650 KHZ - 957-1025-061 REF. DES. DESCRIPTION PART NO. QTY. TABLE 6-49. POWER BLOCK FREQUENCY DEPENDANT KIT, AM-6A, 651 - 770 KHZ - 957-1025-062 REF. DES. DESCRIPTION PART NO. QTY.
Page 134 TABLE 6-54. POWER BLOCK FREQUENCY DEPENDANT KIT, AM-6A, 1581 - 1700 KHZ - 957-1025-067 REF. DES. DESCRIPTION PART NO. QTY. ±...
Page 135 FIGURE TITLE NUMBER...

This manual is also suitable for:

Am-10a

Broadcast Electronics AM-6A Manual

Quick Links

Related Manuals for Broadcast Electronics AM-6A

Summary of Contents for Broadcast Electronics AM-6A

This manual is also suitable for:

Table of Contents