UROVO SR5600 - Bluetooth Scanner Simple Operation Guide
![UROVO - SR5600 - Device Appearance and Commonly Used Buttons Device Appearance and Commonly Used Buttons]()
Packing List
- Device x 1
- Battery x1
- Charger x1
- Data cable x 1
- Direct charger x 1
- Simple Operation Guide&Warranty Instructions&
Certificate of Conformity x 1
Unpacking Instructions
Battery installation instructions
Align the battery with the top of the SR5600 and insert it into the battery compartment. Slide the battery all the way into the SR5600 locking slot to ensure that the battery matches with SR5600.
![UROVO - SR5600 - Battery installation instructions Battery installation instructions]()
Ring installation instructions
Align one end of the SR5600 lock catch and push the other end down until it clicks into place. The ring can be installed as required. The following figure 1 is for the right finger, and figure 2 is for the left finger. Press the sliding buckle to remove the ring.
![UROVO - SR5600 - Ring installation instructions Ring installation instructions]()
Direct charger installation instructions
Insert the bottom of the SR5600 into the direct charger until it clips into place. Connect the Type-C interface at the end of the direct charger with the data cable and charger. Normal charging starts when the indicator light indicates that the red light is always on.
![UROVO - SR5600 - Direct charger installation instructions Direct charger installation instructions]()
Product Instructions
- Press and hold the power button and then release it. After booting, SR5600 Bluetooth scanner (hereinafter referred to as SR5600) automatically enters the Bluetooth Standby Pairing mode, and the blue light keeps flashing;
- If the Bluetooth is not connected, an alarm is generated when theSR5600 scans the code successfully. The SR5600 automatically shuts down if the Bluetooth connection fails in 5 minutes.
- Connect the SR5600 with the main device Bluetooth, there arethree connection methods as follows:
- Search for the corresponding Bluetooth name SR5600-XXXX (representing the last four digits of the Bluetooth Mac address) from the Bluetooth list of the main device.
- Connect via SR5600 NFC touch (press the NFC switch of the maindevice, contact the main device with the SR5600 NFC, and follow the steps prompted by the main device to successfully set up);
- Connect by scanning the setting code (as described in Product Instructions IV).
- After successful connection, the blue light is always on, the buzzer buzz twice, and the device starts working;
- To change the code system and other settings, download thesetting code APK or WeChat setting code applet from the official account of "UROVO". After installation, set according to actual requirements and the QR code will be generated. Scan the QR code with SR5600, and the buzzer buzz twice, which indicates successful setting.
Instructions for Status Light
Status light | Description |
Red indicator light is always on | Scanning code or charging |
Red indicator light flashes once | Setup failure |
Red indicator blinking twice | Alarm during code scanning when Bluetooth is not connected |
Green indicator light flashes once | Scan code successfully |
Green indicator light is always on | Battery fully charged |
Blue indicator light keeps flashing | Bluetooth enters pairing mode |
Blue indicator solid on | Successful Bluetooth connection |
Instructions for Buzz and Vibration
Buzzer, vibration status | Description |
Start-up sound + no vibration | Device successful startup |
One long buzz + vibration | Successful shutdown |
One short buzz + vibration | Successful decoding |
Two short buzz + no vibration | The battery is set successfully, the Bluetooth is connected successfully, and the Bluetooth is disconnected |
One long buzz + no vibration | Setup failure |
Four short beeps + vibration | Alarm during code scanning when Bluetooth is not connected |
![UROVO - SR5600 - Performance parameters Performance parameters]()
Table of Toxic and Hazardous Substances and Content in this product
![UROVO - SR5600 - Table of Toxic and Hazardous Substances Table of Toxic and Hazardous Substances]()
:This symbol indicates that the content of this toxic or hazardous substance in all homogeneous material is under the limit specified in the SJ/T11363-2006
:This symbol indicates that the content of this toxic orX hazardous substance in at least one homogeneous material exceeds the limit specifed in the SJ/T11363-2006; however, the exceeding toxic or hazardous substance in the part with a "x" cannot be solved for there is no mature technology can be used.
This logo refers to the period ( 10 years ) during which the toxic or hazardous substances or elements contained in electronic information products will not leak or mutate so that the use of these [substances or elements] will not result in any severe environmental pollution, any bodily injury or damage to any assets.
![]()
- Risk of explosion if battery is replaced by an incorrect type. Dispose of batteries according to instructions.
- However, there are limitations as to how long a battery can operate or be stored before needing replacement. Many factors affect the actual life cycle of a battery pack such as heat, cold, harsh environmental conditions, and severe drops.
- When batteries are stored over six months, some irreversible deterioration in overall battery quality may occur. Store batteries at half of full charge in a dry, cool place, removed from the equipment to prevent loss of capacity, rusting of metallic parts, and electrolyte leakage. When storing batteries for one year or longer, the charge level should be verified at least once a year and charged to half of full charge.
- Replace the battery when a significant loss of run time is detected.
Battery Safety Guidelines
- The area in which the units are charged should be clear of debris and combustible material or chemicals. Particular care should be taken where the device is charged in non-commercial environment.
- Follow battery usage, storage, and charging guidelines found in the user's guide.
- Improper battery use may result in a fire, explosion, or other hazard.
- To charge the mobile device battery, the battery and charger temperatures must be between 0 and +40.
- Do not use incompatible batteries and chargers. Use of an incompatible battery or charger may present a risk of fire, explosion, leakage, or other hazard.
- For devices that utilize a USB port as a charging source, the devise shall only be connected to products that bear the USB-IF logo or have completed the USB-IF compliance program.
- Do not disassemble or open, crush, bend or deform, puncture, or shred.
- Severe impact from dropping any battery-operated device on a hard surface could cause the battery to overheat.
- Do not short circuit a battery or allow metallic or conductive objects to contact the battery terminals.
- Do not modify or remanufacture, attempt to insert foreign objects into the battery, immerse or expose to water or other liquids, or expose to fire, explosion, or other hazard.
- Do not leave or store the equipment in or near areas that might get very hot, such as in a parked vehicle or near a radiator or other heat source. Do not place battery into a microwave oven or dryer.
- Battery usage by children should be supervised.
- Please follow local regulations to promptly dispose of used re-chargeable batteries.
- Do not dispose of batteries in fire.
- Seek medical advice immediately if a battery has been swallowed.
- In the event of a battery leak, do not allow the liquid to come in contact with the skin or eyes. If contact has been made, wash the affected area with large amounts of water and seek medical advice.
![]()
Documents / ResourcesDownload manual
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Download UROVO SR5600 - Bluetooth Scanner Simple Operation Guide
Need help?
Do you have a question about the SR5600 and is the answer not in the manual?
Questions and answers