Table of Contents
Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for UROVO SR5600
Summary of Contents for UROVO SR5600
- Page 1 SR5600 Bluetooth Ring Scanner [USER GUIDE] [F.2021.07.12].2...
- Page 2 Revision History Change Date Description Author 2021.06.15 First version Liang Wang 2021.07.12 Initial Release Nolan Luo 2021.07.15 Version 1.0 Revision Nolan Luo 2021.07.29 Version 1.1 Revision Nolan Luo 2021.08.08 Version 1.2 Revision Nolan Luo Add prefix/suffix setting Barcode type ...
-
Page 3: Table Of Contents
Index Revision History........................... 2 1. Getting Started..........................1 1.1 Introduction...........................1 1.2 Unpacking..........................1 1.3 Configuration Features......................1 1.4 LED Status Indications......................2 1.5 Buzzer, vibration status......................3 1.6 Battery installation instructions.................... 3 1.7 Trigger Assembly........................4 1.7.1 Installation instructions....................4 1.7.2 Adjust finger strap......................4 1.8 Direct Charger installation instructions................ - Page 4 3. Scanner Setting..........................23 3.1. Scanning Type........................23 3.2. Illumination&Aiming setting....................23 3.3. Illumination level........................24 3.4. Suffix&Prefix........................25 4. Symbologies...........................28 Code 39............................28 Code 39 Full ASCII......................29 PDF417............................30 Data Matrix..........................30 Interleaved 2 of 5........................31 MaxiCode...........................31 UPC/EAN............................31 Code 93............................32 Code 11............................33 Matrix 2 of 5..........................35 NEC 2of 5...........................
-
Page 5: Getting Started
1.1 Introduction This chapter describes the features of the SR5600 Ring Scanner and explains how to install and charge the battery, capture data and reset the SR5600. 1.2 Unpacking Carefully remove all protective material from around the equipment and save the shipping container for later storage and shipping. -
Page 6: Revision History
1.4 LED Status Indications Status light Description Red indicator light is always on Trigger button hold or charging Red indicator light flashes once Setup failure Red indicator blinking twice Alarming/Scanning when Bluetooth is not connected Green indicator light flashes once Scan bar code successfully Green indicator light is always on Battery fully charged Blue indicator light keeps flashing Bluetooth enters pairing mode... -
Page 7: Buzzer, Vibration Status
1.6 Battery installation instructions Align the battery with the top of the SR5600 and insert it into the battery compartment. Slide the battery all the way into the SR5600 locking slot to ensure that the battery matches with SR5600. -
Page 8: Trigger Assembly
1.7 Trigger Assembly 1.7.1 Installation instructions Align one end of the SR5600 lock catch and push the other end down until it clicks into place. The trigger assembly can be installed as required. The following figure 1 is for the right finger, and figure 2 is for the left finger. -
Page 9: Direct Charger Installation Instructions
1.8 Direct Charger installation instructions Insert the bottom of the SR5600 into the charger until it clips into place. Connect the Type-C interface at the end of the charger with the USB cable and Power adaptor. Normal charging starts when the indicator light indicates that the red light is always on. -
Page 10: Bluetooth Communications
Scan a version barcode to check the version number of the scanner. See page10. 1.9.2 Bluetooth Connection Modes The SR5600 Ring Scanner can connect to a host computer using the following Bluetooth modes, scan to switch the connection mode you need: Human Interface Device(*HID MODE) -
Page 11: Pairing Mode
Scan the following barcode to enter the pairing mode or release the connection. 1.9.4 Bluetooth Name Modifying Generate the barcode to change the Bluetooth name, value = $BT#SETSSID=M M: Bluetooth name of Ring Scanner SR5600. 1.10 Command Controlling in SPP Mode This setting enable can make scanner being control by HEX code. -
Page 12: Indicator Controlling
Scan the following barcode to enable command controlling .(HEX: AA 04 40 06 00 42 BB ) 1.10.1 Indicator Controlling Make sure the scanner in SPP Mode and enable the SPP Controlling Mode, then you can send HEX code to control LEDs / Beeper / Vibrate to respond as you wish. Format 1: (Start) (Length of instructs) - Page 13 Green LED Command(1 times): HEX. ON: AA 04 C8 02 01 CF BB OFF: AA 04 C8 02 00 CE BB Start length value 1 value 2 value 3 0xAA 0x04 0xC8 R:0x01， 0x00:OFF XOR(len 0xBB G:0x02， 0x01:ON gth, B:0x04， C8,valu BUZZ:0x value...
- Page 14 Format 2: (Start) (Length of instructs) (Code/default) (R:0x01，G:0x02，B:0x04，BUZZ:0x08, Vibrate:0x10) 00~FF (Blink/beep/vibrate times) 01~FE (Duration)*10ms 02~FF (Interval time)*10ms (XOR result)Can be count by XOR tool or HEX Calculate. (END) Example 1 HEX. AA 06 C0 08 03 0A 14 D3 BB(Means Beeping 3times totally, 100ms duration and wait 200ms between each beep).
-
Page 15: Trigger Controlling
time, 3times totally, 1 seconds duration and wait 2second between each reaction). Start length value 1 value 2 value 3 value 4 value 5 0xAA 0x06 0xC0 R:0x01， times Duration Interval 0xBB G:0x02， *10ms times*10 (length B:0x04， ,value1 BUZZ:0x08, , value Vibrate:0x10 2,value 3,value... -
Page 16: Turn Off All Indications
1.10.4 Turn off all indications Disable all indications: HEX: AA 04 01 07 01 03 BB Enable default indications: HEX: AA 04 01 07 00 02 BB... -
Page 17: Aim/Charcterid Output
1.11 AIM/CharcterID Output Scan the following barcode to receive the barcode type in front of barcode data. The barcode type corresponding format refer to ISO-IEC 15424-2008 and page 53 Programming references. Function Item Parameter Description %5001M% None Disable AIM Code Output Enable Character ID Enable... -
Page 18: Setup
4. Turn the iOS Bluetooth ON. 5. Select Bluetooth Settings and choose SR5600 from the list of discovered devices. The SR5600 displays as SR5600 - xxxx, where xxxx is the The last four digits of the Mac address. 2.2 HID Bluetooth Connection to Android 1. -
Page 19: Hid Bluetooth Connection To Windows
2.3 HID Bluetooth Connection to Windows To start the connection process aim the SR5600 at about 7" (18 cm) away from the computer screen and scan the barcode of the Pairing Mode. The SR5600 Scan LEDs start flashing blue indicating that the SR5600 is attempting to establish connection with the computer. - Page 20 5.Default PIN code is 0000.
- Page 21 <Test in text file.>...
-
Page 22: Power Save
2.4 Power Save If no Bluetooth connection is made within 5 minutes, the ring scanner will auto switch off. Disable power off *Enable power off 2.5 Delay 01~10 ms to send (HID) *1ms 2.6 Inquiry 2.6.1 Inquiry Firmware version Scan the following barcode to return firmware version.(HEX: AA 04 FF 02 00 F9 BB) -
Page 23: Inquiry Bluetooth Mac
2.6.2 Inquiry Bluetooth MAC Scan the following barcode to return Bluetooth MAC address.(HEX: AA 04 FF 02 01 F8 BB) 2.6.2 Inquiry Bluetooth Name Scan the following barcode to return Bluetooth Name.(HEX: AA 04 FF 02 02 FB BB). 2.7 Restore Factory Setting HEX Value: AA 04 FF 01 00 FA BB... -
Page 24: Indicators & Beeper Setting
2.8. Indicators & Beeper setting 2.8.1. Power on alarming 2.8.2. LED indicator(decode) -
Page 25: Beeper Setting(Decode)
2.8.3. Beeper setting(decode) OFF(HEX: AA 02 C2 C0 BB) *ON(HEX:AA 02 C2 C1 BB) 2.8.4. Duration *50ms 2.8.5. Volume Level Middle... -
Page 26: Vibrate Setting (Decode)
*High 2.8.6 Vibrate Setting (decode) 2.8.7 Turn off all indications ON(Turn off) OFF(Turn on*) -
Page 27: Scanner Setting
3. Scanner Setting 3.1. Scanning Type Continuous Barcode Read Pluse *Normal(Manual) 3.2. Illumination&Aiming setting Disable both... -
Page 28: Illumination Level
Laser aiming only Illumination only *Enable both 3.3. Illumination level Level 1 Level 2... -
Page 29: Suffix&Prefix
*Level 3 Level 4 3.4. Suffix&Prefix SR5600 can add 1 prefix and 2 suffix. ‘*’represent default. Multi-step Single-step Function Description Parameter Description Option Disable %3001M Enable Format <data><suffix %3002M 1><suffix 2>... - Page 30 <data><suffix 1> <data><suffix 2> <prefix><data> <prefix><data> <suffix 1> <suffix 2> <prefix><data> <suffix 1> <prefix><data> <suffix 2> Prefix Prefix value 00~FF %3003M Suffix 1 suffix 1 value 00~FF %3004M...
- Page 31 Suffix 2 suffix 2 value 00~FF %3005M...
-
Page 32: Symbologies
This chapter describes symbology features and provides programming barcodes for selecting these features. To set feature values, scan a single barcode or a short barcode sequence. The settings are stored in non-volatile memory and are preserved even when the SR5600 powers down. SPP Command Format: Code 128 Setting:... -
Page 33: Code 39 Full Ascii
1 Check digit 2 Check digit *Do not Transmit Code39 Check Digit(Disable) *Do not Transmit Code39 2 Check Digit(Disable) Code 39 Full ASCII *Disable Code 39 Full ASCII... -
Page 34: Pdf417
Enable Code39 Full ASCII PDF417 Disable PDF417 *Enable PDF417 Data Matrix Disable Data Matrix *Enable Data Matrix... -
Page 35: Interleaved 2 Of 5
Interleaved 2 of 5 *Disable ITF Enable ITF MaxiCode *Disable MaxiCode Enable MaxiCode UPC/EAN... -
Page 36: Code 93
Disable UPC/EAN *Disable UPC/EAN EAN 2 or 5 supplemental setting Disable 2and5 digit supplemental Enable 2 and 5 supplemental Code 93... -
Page 37: Code 11
*Disable Code 93 Enable Code 93 Code 11 *Disable Code11 Enable Code11... - Page 38 Check digit and transmit Disable Code11 *1 check digit 2 check digit Do not transmit 1 check digit Do not transmit 2 check digit...
-
Page 39: Matrix 2 Of 5
Matrix 2 of 5 *Disable Matrix 2 of 5 Enable Matrix 2 of 5 NEC 2of 5 *Disable NEC 2 of 5 Enable NEC 2 of 5... -
Page 40: Hanxincode
Hanxincode *Disable Hanxin Code Enable Hanxin Code GridMatrix *Disable GridMatrix Enable GridMatrix... -
Page 41: Aztec Code
Aztec Code *Disable Aztec Code Enable Aztec Code MicroPDF417 *Disable Micro PDF417 Enable Micro PDF417... -
Page 42: Msi/Plessey
MSI/PLESSEY Disable MSI/PLESSEY(*) Enable MSI/PLESSEY Dotcode Disable Dotcode(*) Enable Dotcode... -
Page 43: Standard 2 Of 5
Standard 2 of 5 Disable Standard 2 of 5 Disable Standard 2 of 5 IATA 2 of 5 Enable Disable*... -
Page 44: Codablock_F
CodaBlock_F *Disable CodaBlock_F Enable CodaBlock_F CodaBlock_A *Disable CodaBlock_A... -
Page 45: Gs1 Databar-14
Enable CodaBlock_A GS1 DataBar-14 *Disable GS1 DataBar-14 Enable GS1 DataBar-14... -
Page 46: Codabar
Codabar *Disable Codabar Enable Codabar Code 2 of 5 *Disable code 2 of 5... -
Page 47: Trioptic
Enable code 2 of 5 Trioptic *Disable Trioptic Enable Trioptic postnet *Disable postnet... - Page 48 Austranlian Post Royal Mail(BPO-4-State) Japan Post Dutch Post(KIX code) US Planet...
- Page 49 US Postnet US4State FICS(UPUID-Tag) USPS 4CB(Intelligent Mail) Canadian Post Planet,Postnet...
- Page 50 Planet,UPU Postnet,UPU Planet,USPS 4CB Postnet,USPS 4CB UPU,USPS 4CB...
- Page 51 Planet,Postnet,UPU Planet,Postnet,USPS 4CB Planet,UPU,USPS 4CB Postnet,UPU,UPS 4CB Planet,Postnet,UPU,USPS 4CB...
-
Page 52: China Post
China Post *Disable China Post Enable China Post... -
Page 53: Ocr
Decoding *Disable OCR Normal Inverse Both... -
Page 54: Ocr Pattern
OCR Pattern User Defined *Passport ISBN Price Field... -
Page 55: Ocr Fonts
MicrE-13 B OCR Fonts OCR-A OCR-B *OCR-A or B... -
Page 56: Ocr Character
MICR SEMI OCR Character Numeric Alpha... -
Page 57: Ocr Character Length : 00~Ff
Alphanumeric *Any (include space) OCR Character length : 00~FF... -
Page 58: Programming Reference
5.Programming Reference Linear Symbologies Symbology Codabar Code 11 Code 128/ISBT 128 EAN128/GS1128 Code39 Code 93 EAN-13/ISBT 13 EAN-8 GS1 DataBar GS1 DataBar Limited GS1 DataBar Expanded China (Hong Kang 2 of 5) Interleaved 2 of 5 Matrix 2 of 5 Straight 2 of 5 IATA Straight 2 of 5 Industrial IATA 2 of 5... -
Page 59: Postal Symbologies
QR Code Micro QR & Postal Symbologies Symbology Australian Post British Post Canadian Post China Post Intelligent Mail Bar Code Japanese Post Netherlands Post(KIX) Planet Code Postnet...
Need help?
Do you have a question about the SR5600 and is the answer not in the manual?
Questions and answers
Здраствуйте , подскажите пожалуйста , подключаю сканер к тсд , сопряжение проходит успешно , работает ровно 30 сек и отключается от блютус , но при этом сам сканер не отключается , в чем проблема ? Также при подключении перестаёт гореть индикатор, почему?
The UROVO SR5600 scanner automatically shuts down if the Bluetooth connection fails within 5 minutes. If the scanner disconnects after 30 seconds but remains powered on, the issue could be an unstable Bluetooth connection or interference. Additionally, the indicator light turning off during connection may indicate an unsuccessful pairing or a power-related issue. Ensuring a stable Bluetooth connection and verifying the main device's Bluetooth settings may help resolve the issue.
This answer is automatically generated