Table of Contents
Advertisement
Using the TV's Menu System
Main Menu
Connections
0
Go Back
Select what should occur when power is restored to the TV:
1
Text here
Initial Channel
Off: Initial Channel is disabled
2
Initial Volume
On: Go to last input or channel selected
Cable Input
3
On: Go to
Maximum Volume
Channel
4
CableCARD Tools
5
Note: An Initial Channel setting of "On" will be enabled only
Remote Setup
when the TV is plugged back in or electricity is otherwise
restored to the TV. Initial Channel is not enabled from the
turning on of the TV with the remote or front buttons.
Press 5 or 6 to point to an option, then press OK to
select it. Press 3to return to the menu.
Main Menu
Connections
0
Go Back
Network Setup
1
Initial Channel
CableCARD™ Status
CableCARD™ Pairing
2
Initial Volume
Conditional Access
3
Maximum Volume
4
CableCARD Tools
5
Remote Setup
Two lines of help text will apear in this area to explain the
feature and instruct the user on how to use it.
Example status screen for
digital cable television
service.
Example status screen for
digital cable television
service.
Example status screen for
digital cable television
service.
Example status screen for
digital cable television
service.
Example status screen for
digital cable television
service.
Example status screen for
Continue
Main Menu
Connections
0
Go Back
Select the remote mode that this TV should respond to:
TV (default)
1
Initial Channel
Text here
TV2
2
Initial Volume
TV3
3
Maximum Volume
Use this screen if you want to set up this RCA TV
4
to respond to a different RCA TV remote mode. By
CableCARD Tools
doing so, you can independently control two RCA
5
Remote Setup
TVs that are near each other simply by changing the mode
of the remote. A third RCA TV can be added to the
same location and controlled separately if it has this screen
and is set up to respond to a remote mode that is different
than the first two RCA TVs.
Remote Setup can be used to control up to three TV's in the
same location. Press OK to continue.
Main Menu
Connections
0
Some Internet Service Providers (phone/cable company)
Go Back
may require you to provide them with your TV's Ethernet
1
MAC (Media Access Control) address and assign you with a
Host Name
Host Name
device host name to enter below. This is usually NOT
2
IP Address
required if connecting to an ISP through an Ethernet
gateway device (e.g. router) supporting NAT/PAT,
3
Proxy Server
sometimes referred to as a DSL/Cable Modem router.
4
Reset All
This is your device's MAC address:
00 11 22 33 44 55
If your Ethernet gateway device supports DHCP, the
Domain Name will appear here:
domain.name.here.
If required, enter the device hose name below:
Use the keyboard or the remote's arrow keys to enter the
host name. This may be the only setup you need to do.
58
Special Features
Special Features
The special features options are mostly intended for commercial/retail use.
999
Sub-channel
999
Special Features
Special Features
Ethernet Setup
Ethernet Setup
An Ethernet connection allows your TV to be upgraded if a software upgrade is
available. Connect your TV to a router and cable modem via the ETHERNET
jack. Then, go to the Software Upgrade menu to see if a software upgrade is
available. If you have a NAT (Network Address Translation) /PAT (Port Address
Translation) component with DHCP capability (router, etc.), no setup is
required. The TV automatically sets itself up for Ethernet use. If you do not have
a NAT/PAT router, you may need to establish some settings in conjunction with
your ISP (Internet Service Provider) before you can connect to the Internet.
If an IP address isn't assigned for you, contact your network administrator for
the necessary information.
A Reset All selection is provided for your convenience if you move to another
city and must enter new information, or enter some incorrect information.
Initial Channel You can select the tuner and channel or input that your
TV tunes to each time the TV is turned on by plugging it back in.
Initial Volume This feature works only if the Initial Channel feature is set
to On. Select the volume level that you want when the TV is turned on.
Maximum Volume This feature is intended to stop the volume from
being turned up too loudly. Set the volume at the loudest level you would
want to hear.
CableCARD Tools Displays information available for digital cable TV
services when a CableCARD is inserted in the back of the TV and you have
subscribed to digital cable service. Go to page 18 for more information on
using your CableCARD.
The CableCARD Tools information might vary according to the brand of card
you have inserted into your TV. The graphic to the left is an example of
what you might see. Select an option to view more information.
Some CableCARD Tools screens might have additional information displayed
on more than one page. Use the arrow buttons on the remote to highlight
the blue Continue link at the bottom of the page, for example, as the
graphic to the left shows, and simply press the OK button on the remote to
read more text. If more than one link appears, use the arrow buttons to
highlight the one you want. To exit the screen, press CLEAR on the remote.
Remote Setup This features allows you to control three different RCA TVs.
This is helpful if you have two or three RCA TVs near each other, and they
also have this menu option, but you want to control them independent of
each other. Program a second RCA TV to the DVD, VCR, AUX, SAT/CABLE,
or AUDIO component button, using the TV2 code 1222. Select the TV2
option in that TV's Remote Setup menu. If you have a third RCA TV,
program a component button using the TV3 code 1223. Select the TV3
option in that TV's Remote Setup menu. Go to Chapter 2 for more
information on programming your remote.
Chapter 4
Advertisement
Table of Contents
