Advertisement
Quick Links
Note: Room must be installed on flat, level surface.
710-0124 IG-810-SH / S810-H 1 Person IR Sauna
Ver. 2
1 Person Infrared Sauna
Touch Pad and Bluetooth
IG-810-SH/S810
This Product is covered by:
US Patents No. 8,692,168
Canadian Patents No. 2,729,500
and other Patents Pending.
Precautions Before Use
Preassembly Information
Electrical Requirements
Sauna Assembly
Electrical Connection-Under Bench
Electrical Connection-Inside Ceiling
Control Panel Instructions
Lighting Operation
Audio System
How to Use Sauna
Tips & Troubleshooting
Wiring Diagram
Warranty
S-Series
User Manual
2,794,059 & 2,813,340
Page 1
2
2
3
4
8
13
16
16
17
18
19
20
21
01-14-16
Rev. 3
Advertisement
Related Manuals for TyloHelo S Series
Summary of Contents for TyloHelo S Series
- Page 1 S-Series 1 Person Infrared Sauna Touch Pad and Bluetooth IG-810-SH/S810 User Manual This Product is covered by: US Patents No. 8,692,168 Canadian Patents No. 2,729,500 2,794,059 & 2,813,340 and other Patents Pending. Note: Room must be installed on flat, level surface. Precautions Before Use Preassembly Information Electrical Requirements...
-
Page 2: Precautions Before Use
Precautions before Use: Warning (Room Configuration & Use): Proper Electrical Grounding is Required Electrical Receptacles not Allowed in the Room Do not Apply Water to any Heating Element Do not Add a Locking or Latching System to the Door ... - Page 3 Electrical Requirements: The IR Sauna Room is designed for a 120 Volt AC / 15 or 20 Amp Circuit Breaker! A 120 Volt AC (dedicated) circuit is recommended to avoid unnecessary tripping of the breaker. The Sauna should be plugged into a NEMA (5-15R or 5-20R) Amp electrical outlet.
- Page 4 Sauna Assembly Instructions _________________________________________________________________________ Floor Panel (Box #1): Locate the Floor Panel on a level surface (3-6) inches from wall and no more than (5 ft) from 120 Volt AC / 15 amp dedicated receptacle. Position the Floor panel so that the Ceramic tiles / IR Floor Heaters are to the front of the room Note: place the Ceiling, Bench Skirt and Bench to the side until the appropriate steps.
- Page 5 Back Wall (Box #3): Note: after opening the box 3 -- store Front Wall panel until that step of the assembly process. sure to control the door from opening when moving the Front Wall Panel to prevent breakage. Place Back Wall panel into the back slot of the Floor Panel. ...
- Page 6 Right Wall (Box #2): Place Right Wall section into the right slot of the Floor Panel Attach Back Wall to the Right Wall by lifting up the Right wall sliding into the corner interlock brackets. Left Wall (Box #2): ...
- Page 7 Bench Skirt (Box #1): Insert the Bench Skirt in between the Right Wall and the Left Wall panels tracks. Slide Bench Skirt all the way to the floor. Do not pinch any wires under the skirt. Latch the buckles securing the floor to the Bench Skirt. Do not latch the buckles for the left and right wall panel at this time.
- Page 8 Electrical Connections (under bench - right side): Connect wire #4 from distribution plate to #4 from Back Wall harness. Connect wire #5 from the distribution plate to #5 from the Back Wall harness. Connect wire R1 from the distribution plate to R1 from the Right Wall junction box. ...
- Page 9 Electrical Connections (under bench - left side): Connect wire L1 from the distribution plate to L1 from the Left Wall panel. Connect wire B1 from the distribution plate to B1 from the Back Wall panel. View of the finished connections. ...
- Page 10 Use the buckles to latch the skirt to the left and right side walls. Bench top can now be fit into place. Bench must tuck under the back heater guard and then push all the way to the back wall. ...
- Page 11 Front Wall (Box #2): Place the Front Wall panel into the Floor panel slot. Lock Front Wall panel into place by slightly lifting it higher than the Right & Left Wall panels and pushing inward as lowering the Front Wall panel. Note: Secure the door from falling open and breaking while setting the Front Wall panel.
- Page 12 Ceiling (Box #1): Install 4 large Styrofoam packing squares on top of the Right & Left Wall panels. One block should be placed in the front portion and one toward the rear portion of each wall. These will be used to set the ceiling on. ...
- Page 13 Lower the Ceiling panel by removing the rear Styrofoam blocks first and then the front blocks. Be sure not to pinch any wires under the Ceiling panel. Turn the wood ceiling cam locks to lock the ceiling into place. Electrical Connections (inside the Ceiling panel-back right corner): ...
- Page 14 Electrical Connections (inside Ceiling-Left front corner): Near the Touch Screen harness in Ceiling connect Left Wall wire #3 to Ceiling wire #3. Connect Left Wall wire #7 to the Ceiling wire #7. Connect Left Wall wire F to Ceiling wire F. ...
- Page 15 Deluxe Door Handles: Your sauna comes equipped with a deluxe door handle. Locate brown box (typically in the floor/ceiling carton) Step 1. Separate two pieces by loosening four set screws with Allen wrench provided. Step 2. Remove bolts and spacer from first handle piece. You will need a Phillips Screw driver.
- Page 16 Control Panel Instructions: Color Therapy Bench Heat Lights Interior Lights Valance Power ON or Light Main Power: Press POWER to switch room ON or OFF Timer Functions: Press and hold “+” or “–“ to set room operating time. Increases time (5 minute increments) / Decreases time (5 minute increments) Temperature Functions: Press to alternate between either C or F (C or F will light to indicate the units desired) Press and hold + or –...
-
Page 17: Audio Operation
Audio System: Audio Power ON or OFF Auxiliary Input AUDIO OPERATION Audio Power On Press Bluetooth icon to turn on or off audio system Blue LED indicates the audio system is operating. Bluetooth Bluetooth is always enabled when blue LED is glowing and Aux Input is not connected Auxiliary Input ... - Page 18 How to Use Infrared Sauna: Avoid eating large meals and excessive alcohol intake before using Sauna. Never smoke or drink alcohol or exercise inside of Sauna. If you are taking any medications or under the care of a Physician, consult with them prior to Sauna usage. Refer to Sauna Usage Warning signs located inside of Sauna Room Prior to Sauna session, if possible before using Sauna, take a warm shower without drying.
-
Page 19: Troubleshooting Tips
Ensure the floor is flat by using a level on the ceiling of the room. It may be necessary to use a small door or window shim to adjust the level under the floor. ------------------------------------------------------------------------------------------- For additional assistance or service questions? Please do not hesitate contacting Saunatec/TyloHelo Mon – Fri. 8AM – 5PM CST 1-888-780-4427 techsupport@tyloheloinc.com... - Page 20 710-0124 IG-810-SH / S810-H 1 Person IR Sauna Page 20 01-14-16 Ver. 2 Rev. 3...
- Page 21 710-0124 IG-810-SH / S810-H 1 Person IR Sauna Page 21 01-14-16 Ver. 2 Rev. 3...
Need help?
Do you have a question about the S Series and is the answer not in the manual?
Questions and answers
I have a IR sauna and the panel reads Carbon Flex by Tylo Helo. I’ve had a few years and have been able to connect to speakers via Bluetooth until recently. What is best way to reconnect?
To reconnect Bluetooth speakers to your TyloHelo Carbon Flex IR sauna panel:
1. Press the Bluetooth icon to turn on the audio system.
2. Ensure the blue LED is glowing, indicating Bluetooth is enabled.
3. Make sure no 3.5 mm Aux Input cable is connected, as this disables Bluetooth.
4. Connect your Bluetooth device to the sauna system using its Bluetooth settings.
This answer is automatically generated