Page 1
IS 44 BT Room Owner’s Manual with IS SaunaLogic Control Bluetooth Sound System Precautions before Use…………………………………………………….….…….…… 3 Read Before Installation…………………………………………………………..……... 4 Room Assembly……………………………………………….………………….……… 5 Lighting Operation………………………………………………….…………………..IS 44 Room Operation…………………………………………….……………….…….. 9 Infrared/Sauna Tips and Tricks……………………………………….…………….……. 11 Troubleshooting and Maintenance………………………………….……………..…….. 12...
Read all instruction carefully before installation including instructions packaged separately with the sauna heater. Please leave all instructions and warranty with the owner. WARNING : When using electrical sauna heaters and associated sauna products, basic precautions must be followed, including the following: 1.
ROOM ASSEMBLY The 1.7kw can be used on all 15 amp or 20 amp household outlets (the standard 120 volt outlet found in all homes). A dedicated circuit is advisable to avoid unnecessary tripping of the breaker. Each panel is heavy. Be careful to avoid injury when installing, especially the top panel. Two adults are required for the installation of sauna room.
Page 4
Step 1. Step 2. Place the floor on a flat level Place side wall on sauna floor surface (you many need to use wood interlocking the two wall panels shims to assist with leveling. Shims together (repeat for the other side are not provided).
Page 5
Step 3. Connect heater in to the water tight plug. Place the heater inside of the room. Final installation of heater in Step 8. Step 4. Connect the two black junction boxes, located on the lower left and right wall corner. R1 to the Right wall, L1 to the Left wall.
Page 6
Step 6. Connect the S1 junction box on the bench skirt and install the top bench. Place heater on the floor in front of the benches. Step 7. Front wall and ceiling installation. Place the front wall in the slot in the floor. Lift each corner to slide and lock into place. This step will require two people.
Page 7
Step 8. Connecting the wires in the ceiling. Right Side Wall above Sensor Front compartment above control. Connect C to C Connect B to B Connect 6 to 6 Connect 4 to 4 Back compartment connections Connect 5 to 5 71-0145 Page 7 07/29/18...
Page 8
Remove heater mounting plate from the back of the heater. With the 1” screws provided Step 9. with the heater, fasten the heater mounting plate to the wood brackets. The upper left screw (closest to the wall) should be 5” from the wall and 24-3/4” from the floor. Then put the two lower screws in the holes.
Page 9
IS SAUNALOGIC CONTROL OPERATION for IS 44 ROOM Lighting Press External Light Icon (light bulb outside a box) to toggle on or off the lights. Press Internal Light Icon (light bulb inside a box) to toggle on or off the lights. Press Color Light Icon (light bulb with a color pallet) to scroll through the colors and then off.
STARTING EITHER HEATING SYSTEM IMMEDIATELY Immediately after pressing the Power On button, the selected heating system will engage. The heater(s) will turn on and begin heating the room to current set points. At the end of the selected time (60 minutes maximum), the heating system will turn off. The control display will turn off and all lights will turn off 5 minutes after heating system.
Page 11
Important Information about your new IS 44 Sauna Infrared Saunas have a typical operating range of 100°F (38°C) to 115°F (46°C). This lower heat range is ideal for users new to sauna bathing and the lower temperature does not dry out mucus membranes.
Sauna Heater Tips and Tricks Before using your new sauna heater, verify proper rock placement, wall sensor placement and the wall thermometer is placed no more than 12” from the ceiling near the seating area. Steam- Your new sauna heater is designed to have water ladled on the rocks. Proper use of water in the sauna is important.
Need help?
Do you have a question about the IS 44 BT and is the answer not in the manual?
Questions and answers