Summary of Contents for Oricom JSP1200
- Page 1 Operating Instructions JSP1200 Waterproof Jump Starter Keep this user guide for future reference. Always retain your proof of purchase in case of warranty service. www.oricom.com.au...
-
Page 2: Table Of Contents
Table of Contents Product Overview ..........3 Package Contents ..........5 Getting Started ..........5 Speci cations ........... 8 FAQ ..............10 Care and Maintenance ........11 Express Warranty (Australia) ......12 Cautions • DO NOT use this unit if any cable, clamp, or cord is damaged. •... -
Page 3: Product Overview
Product Overview Product Overview NO. Function Operation ON/OFF Button Connect devices to be charged. (Multifunctional) LED’s light up indicating battery capacity. If no devices are connected press the button to show the battery capacity. Press and hold the button to turn the torch on/off. - Page 4 Product Overview USB-A Output Port Use to charge your devices (QC 1 (QC 3.0) 3.0 compatible) faster, with 75% increase in speed. USB-A Output Port Use to charge your devices (QC 2 (QC 3.0) 3.0 compatible) faster, with 75% increase in speed. USB-C Input &...
-
Page 5: Package Contents
Package Contents / Getting Started Package Contents 1 x JSP1200 Jump Starter 1 x 12V Car charger 1 x Smart Battery Clamp 1 x AC Charger 1 x USB-C to USB A Cable 1 x User Manual 1 x USB-C to USB C Cable... - Page 6 Getting Started Jump Start Your Car NOTE: This jump starter is designed for a 12V car system (all petrol engines up to 8.0L and diesel engines up to 6.0L only). Check to make sure that 3 to 4 indicator lights are illuminated (battery level is above 50%) before you jump start your car.
- Page 7 Getting Started Step 3 (a): Start your car. If your car fails to start, disconnect the battery clamp from the vehicle and the jump starter. Wait for at least 30 seconds, then try again. If your car fails to start, you can use the force start function.
-
Page 8: Speci Cations
The green light The voltage of the jump starter is too low. ashes slowly Charge the jump starter before attempting to re-use. Speci cations Model JSP1200 Capacity 59.2Wh Ingress Protection IP66 Micro USB input 5V/2.1A Torch 1W LED, 100 lumens Type-C input &... - Page 9 Speci cations Type-A USB output 1 5V/3A, 9V/2A, 12V/1.5A Type-A USB output 2 5V/3A, 9V/2A, 12V/1.5A Start current 600A (lasts for 1.5S) Start current 350A (lasts for 3S) Peak current 1200A (lasts for 0.1S) Short circuit protection Effective Over-discharge protection ≤13V±0.3V °...
-
Page 10: Faq
Q: How to turn off the jump starter? A: The jump starter will power off automatically when no load is detected or when charging is complete. Q: How long does it take to fully charge the jump starter? A: About 9 hours through the Micro USB input port or 3 hours through the USB C input port. -
Page 11: Care And Maintenance
• Keep the jump starter away from children and pets. Need Help? If you need assistance setting up or using your Oricom product now or in the future, call Oricom Support. Australia (02) 4574 8888 www.oricom.com.au... -
Page 12: Express Warranty (Australia)
In the event of a minor failure, Oricom reserves the right to choose to repair or replace the product. - Page 13 Oricom. Oricom will not be liable under this Express Warranty, and to the extent permitted by law will not be liable for any defect, loss, damage or injury arising out of or in connection with a: 1.
- Page 14 Products that are authorised to be returned to Oricom in Australia must include all of the following: • A completed Return Authorisation form • A copy of your Proof of Purchase (please keep your original copy) •...
- Page 15 Express Warranty (Australia) delivery, freight, transportation or insurance of the product) to return the faulty product to us, however, we will arrange delivery of the repaired or replaced faulty product to you. Important Information - Repair Notice Please be aware that the repair of your products may result in the loss of any user-generated data (such as stored telephone numbers, text messages and contact information).
- Page 16 Oricom Support - Australia For all product enquiries, troubleshooting or to discuss the range of Oricom products, feel free to contact Oricom or visit our website for answers to frequently asked questions. (02) 4574 8888 Monday - Friday 8am - 6pm AEST Email: support@oricom.com.au...
Need help?
Do you have a question about the JSP1200 and is the answer not in the manual?
Questions and answers