Safety Information - GE Profile OPAL 2.0 Owner's Manual
Hide thumbs
Also See for Profile OPAL 2.0:
- Owner's manual (56 pages) ,
- Owner's manual (56 pages) ,
- Owner's manual (60 pages)
Table of Contents
Advertisement
Available languages
Available languages
IMPORTANT SAFETY INFORMATION
READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE
WARNING
these basic safety precautions.
product must be properly grounded.
the ice maker is connected to its own circuit. Use only a 115
in accordance with the National Electric Code and local
codes and ordinances.
electrical rating of the cord be 15 Amperes (minimum) and
120 Volts.
accordance with the installation instructions before it is
outdoors.
product.
maker. They could seriously injure themselves.
CAUTION
To reduce the risk of injury when using your Opal, follow these basic safety precautions.
labels from your ice maker.
Refrigerant and Foam Disposal
special disposal procedures. Contact your local authorities for the environmentally safe disposal of your appliance.
WARNING
FIRE OR EXPLOSION HAZARD Flammable Refrigerant
This appliance contains isobutane refrigerant, also known as R600a, a natural gas with high environmental
compatibility. However, it is also combustible. Adhere to the warnings below to reduce the risk of injury or
property damage.
1. When handling, installing, and operating the appliance, care
should be taken to avoid damage to the refrigerant tubing.
disposal procedures. Contact your local authorities for the
environmentally safe disposal of your refrigerator.
READ AND SAVE THESE INSTRUCTIONS
49-9000029 Rev. 6
hot surfaces.
is damaged.
use.
part of your product.
in this user manual.
manufacturer.
should be taken to avoid damage to the refrigerant tubing.
personnel and component parts shall be replaced with
and install the ice maker in order to prevent injury.
4. Keep ventilation openings in the appliance enclosures or in
5. To remove frost, scrape with a plastic or wood spatula or
flammable refrigerant tubing behind it.
compartment of the appliance.
3
Hide quick links:
Advertisement
Chapters
Table of Contents
Need help?
Do you have a question about the Profile OPAL 2.0 and is the answer not in the manual?
Questions and answers
How can I replace the tubes?
To replace the tubes on a GE OPAL 2.0 ice maker:
1. Pull the sides up, pry from the back, and remove the covers.
2. Use pliers to remove the metal clips and hoses.
3. Press the clips on both sides to remove the reservoir lid.
4. Cut any zip ties attaching the hoses.
5. Remove the old tubing.
6. Install new clear tubing as a replacement.
7. Reattach any necessary clips and replace the zip ties.
Make sure to clean any buildup before installing the new tubes.
This answer is automatically generated
What does the blinking "Cleaning" light indicate during normal usage?
The blinking "Cleaning" light on the GE Profile OPAL 2.0 indicates that the unit requires cleaning.
This answer is automatically generated
I cleaned it but now water want go from side tank to ice maker
Water may not be flowing from the side tank to the GE Profile OPAL 2.0 ice maker due to one or more of the following reasons:
1. Incorrect Tube Connection: The tube labeled "Tube B" (marked "Side Tank") must be properly connected. If it's not correctly attached, water will not flow.
2. Air in the Line: If air is trapped in the tube, it can block water flow. Ensuring a proper seal and priming the line may help.
3. Water Not Drained First: If there's water already in the internal reservoir, the system may not draw from the side tank until the main reservoir level drops.
4. Side Tank Not Installed Properly: The tank must be seated correctly and connected tightly to ensure proper flow.
5. Clog or Debris: Blockages in the tube or connection point may stop water flow.
6. Ice Maker Turned Off: The ice maker should be turned off during setup and then turned back on once the side tank is connected.
Check all connections, ensure the tank is full and seated properly, and make sure the tubing is clear and correctly attached.
This answer is automatically generated