Mastervolt 77010600 Quick Start Installation Manual

Specifications

Model: SmartRemote
Product code retail: 77010600
Product code OEM: 77010500
Dimensions: 72×72×30 mm/2.8×2.8×1.2"
Screen: 320x240 pixels,
16 bits color, 2.8"
Weight: 75 g / 0.2 lb
Operating temperature: -20 to 55°C/-4 to 131°F
Relative humidity: max. 95% non-condensing
Storage temperature: -30 to 70°C/-22 to 158°F
bus powered, 11-14V *
Power supply:
<
Power consumption: 180mW (idle mode)
Protection degree: IP20
Approvals: CE
Interfaces: MasterBus,
CZone (upcoming)
* The paired device must have MasterBus
powering set to on.
For additional information, like supported devices,
please visit our website: www.mastervolt.com

Meaning of the icons

Device state (
inverting/charging/standby
Battery voltage or charging current
Output power (AC OUT)
Shore power (AC IN)
Energy left in battery (State of Charge)
Time remaining during discharge
10000015712/04
WARNING
If you are not knowledgeable about electrical
systems, have an electrical professional install this
unit.
CAUTION
The SmartRemote is not waterproof. Do not install
where the display is exposed to water.

Warranty

The Mastervolt product warranty covers the
SmartRemote for the first two years after the
purchase date.
The warranty is limited to the cost of repair and/or
replacement of the product. Costs of labor or
shipping are not covered by this warranty.
Mastervolt cannot accept liability for damage due to
the misuse of the SmartRemote.

Correct Disposal

Contact your local waste disposal depart-
ment to properly dispose of the unit.
)
EUROPE, MIDDLE EAST & AFRICA
Snijdersbergweg 93
1105 AN AMSTERDAM
The Netherlands
+31 (0)20 34 22 100
info@mastervolt.com
AMERICAS & CARIBBEAN
N86 W12500 Westbrook Crossing
Menomonee Falls, WISCONSIN 53051
USA
+1 800 307 6702
tsusa@mastervolt.com
ASIA/PACIFIC
42 Apollo Drive, Rosedale
AUCKLAND 0632
New Zealand
+ 64 9 415 7261
enquiries@bepmarine.com
SmartRemote
QuickStart Installation Guide

Components included

Head unit Surface
mount bezel
4 × Phillips
countersunk
self-tapping
Bayonet collar
screws (2.9×16)
Mastervolt CZone Drop Cable
*
(1m / 3.3ft)
MasterBus cable MasterBus Terminator
*
(6m / 20ft)
*
Need to be ordered separately with OEM packaging
To download this guide in other languages,
please visit our website: www.mastervolt.com

On first use

When the SmartRemote is added to a MasterBus
Network, it will scan for available supported
devices to pair with. If there is only one device, it
will automatically pair with this device. If there are
multiple devices, it will ask to select a device.
When changing the
language, be aware
that language of the
SmartRemote and
language of the
paired device are two
P1 P2 P3
separate settings!

Operation Notes

The three push buttons P1, P2 and P3 provide a
scroll and select function. Their behavior depends
on the paired device. When idle, the button menu
slides down. To get it back, press any button.
To wake up from standby mode, simultaneously
press P1 and P3 to enter the main menu. Standby
time can be changed.
How to switch an inverter e.g. on or off?
When the SmartRemote is active, press any key to
reveal the sub menu. Press P1 to switch on or off.
How to adjust the power sharing level?
When the SmartRemote is active, press any key to
reveal the sub menu. Press P2 or P3 to select the
required AC IN limit.
How to select another device?
First, unpair the currently paired device:
simultaneously press P1 and P3 to enter the main
*
menu. Scroll down to Unpair device and press the
checkmark button. Confirm the action by pressing
the checkmark button again. The SmartRemote
will scan for available devices. If there is only one
device, it will automatically pair with this device. If
there are multiple devices, it will ask to select a
device.