Related Manuals for Hunter 50008
Summary of Contents for Hunter 50008
- Page 1 Lakemont Installation Manual Model: 53997 Matte White 50008 Matte Silver Fan weight ±2 lbs: 22.9 lbs (10.4 kg) ©2020 Hunter Fan Co. PG3854 r012120...
- Page 2 - All wiring must be in accordance with national and local electrical codes ANSI/NFPA 70. If you are unfamiliar with wiring, use a qualified electrician. c.2 - Use only Hunter replacement parts. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
- Page 3 We recommend that you pull everything out of the box and lay it out. We have grouped the drawn components below with the hardware you’ll need for those Hunter Pro Tip: parts. The screws below are drawn to scale to make it easier to identify what piece of hardware is needed to install each component.
-
Page 4: Choosing The Right Installation Location
A little more information on Angled Mounting: For optimum performance and appearance, a longer downrod should be used with your Hunter ceiling fan when installing on high or angled ceiling. If your ceiling is angled greater than 34° you will also need an Angled Mounting Kit. -
Page 5: Installing The Ceiling Bracket
You have two options for installation. Pick which one works best for your location. Remove any existing Hunter Pro Tip: bracket prior to installation. Only use the provided Hunter ceiling bracket that came in your fan’s box. The machine screws are the ones that came with your outlet box. -
Page 6: Hanging The Fan
1886 Hanging the Fan NOTICE To prevent damage to fan, ALWAYS lift holding either the fan housing or the downrod. Place the downrod ball into the slot in the ceiling bracket. Ceiling Bracket Downrod Hanging Fan Wiring Canopy Blades Light Remote Troubleshooting... -
Page 7: Wiring The Fan
If you are unfamiliar with wiring or uncomfortable doing it yourself, please contact a qualified electrician. You are going to need these: Hunter Pro Tip: Here is how to connect the wires: 4 Wire Nuts (these are in the... -
Page 8: Installing The Canopy
1886 Installing the Canopy Insert the two canopy screws found in the hardware bag. Canopy Screw Lift the canopy into place so that NOTICE the screw holes are aligned. If screw holes do not align properly then rotate the canopy 180 degrees. -
Page 9: Installing The Blades
1886 Installing the Blades: Slide the blades into position. Ensure that the blades do not overlap one another. Align the holes in the blade arms with the holes on the fan. Repeat x3 Put the blade washers found in the hardware bag onto the blade screws found in the hardware... -
Page 10: Assembling The Light Kit
1886 Assembling the LIght Kit 1 of 6 2 of 6 Light Kit Screw Light Kit Screw Insert the third screw, Feed the wire plug through the found in the hardware center hole of the upper switch bag, into place and then Partially install two light kit housing, then wrap keyhole tighten all three screws. -
Page 11: Preparing The Remote
1886 Preparing the Remote For your convenience, a remote function card The remote transmitter is already is packed in with your remote. paired to the receiver and ready to use. Dimming mode is off by default. Note: If you need to pair your remote, To access the battery compartment, turn fan power off and back on at the remove the the battery door to the... -
Page 12: Troubleshooting
Hunter instructions, accidental damage caused by the fan owner or related parties, Please do not ship your fan or any fan parts to Hunter. Delivery will be refused. modifications to the fan, improper or incorrectly performed maintenance or repair,... - Page 13 1886 Downrod If you need a different downrod length follow these steps: Follow steps 1-5 to remove standard downrod pipe Follow steps 6-10 to reassemble with new downrod WARNING FAN FALL HAZARD To prevent SERIOUS INJURY or DEATH: • ALWAYS follow the downrod assembly instructions exactly.