JABSCO 11860-0005 Manual

SELF-PRIMING PUMPS
ELECTRO-MAGNETIC CLUTCH UNIT
FEATURES
Body: Bronze
Impeller: Nitrile
Shaft: Stainless Steel
Seal: Carbon-Ceramic, Face Type
Ports: 11860-Series, 1" NPT Internal
11870-Series, 1-1/4" NPT Internal
Bearings: Shielded Ball Bearings
Weight: 11860-Series, 15 lb (6.8 kg) Approx.
11870-Series, 19-1/2 lb (8.9 kg) Approx.
Clutch
Model
Volt/Belt
11860-0005 12 / 2-A
11860-0045 12 / 1-B
11860-0006 24 / 2-A
11860-0046 24 / 1-B
11860-7001 12 / 2-A
11860-0051 12 / 2-A
11870-0005 12 / 2-A
11870-0045 12 / 1-B
11870-0006 24 / 2-A
11870-0046 24 / 1-B
11870-0007 32 / 2-A
APPLICATION
MARINE: Pumping bilges, Washdowns, Circulating
water in bait tanks, Utility dock-side pump.
INDUSTRIAL: Circulating and transferring, Velocity-
mixing, Pumping machine tool coolants, Return spill,
Sump drainage, Chemicals, Pharmaceuticals, Soap,
Liquors, Ink, Dyes, Alcohol, Various acids, Tanning
Liquors, Glycerine, Brine, etc.
FARMING: Pumping water stock, Pumping water from
shallow wells and cisterns.
PLUMBING AND HOME EMERGENCY USE: Pumping
out flooded basements, Cesspools, Sumps, Water
heaters and water closets, Drains and sinks, Draining
fishponds and pools.
PUBLIC UTILITIES AND MUNICIPALITIES: Under the
hood mounting on service trucks for draining meter
boxes, manholes, excavations; For pollution control
and watering for dust control.
INSTALLATION
Pump may be mounted in any position. Intake and
discharge ports are determined by the direction of shaft
rotation (refer to dimensional drawing). Before
installing, energize clutch and turn pump shaft in direc-
tion of shaft rotation. Drive pump with two "A" size belts
or one "B" size belt. Avoid dry-running by using Vacuum
Switch Model 4732-0000 for automatic shutoff.
Cam Impeller Insert
Brass Nitrile Brass
Brass Nitrile Brass
Brass Nitrile Brass
Brass Nitrile Brass
Brass Neoprene Brass
Brass Neoprene Brass
Brass Nitrile Brass
Brass Nitrile Brass
Brass Nitrile Brass
Brass Nitrile Brass
Brass Nitrile Brass
Models 11860-Series
WIRING
Connect wires as shown for manual on-off operation.
Install appropriate size fuse (see Electrical Specification
Chart) in positive lead as close to power source as
possible. For complete wiring instruction, see diagram
on last page.
Connect wires as shown for manual on-off operation.
ELECTRICAL SPECIFICATIONS
Voltage Amp Draw
12
24
32 1.5
OPERATION
Pump will self-prime at low or high speeds. Make sure
that all connections are airtight. 12 Volt models are
equipped with mechanical clutch engagement
screws in case of electrical failure. To mechanically
engage clutch, loosen locking nuts, tighten allen
head screws and retighten locking nuts. Reverse pro-
cedure to disengage clutch. If the mechanical
engagement feature is not desired, the screws may
be removed. DO NOT RUN PUMP DRY FOR MORE
THAN 30 SECONDS. LACK OF WATER FLOW MAY
DAMAGE IMPELLER. To drain pump, loosen end
cover screws. See Head Capacity Table for head pres-
sures and flow. To avoid costly shutdowns, keep a
Jabsco Service. Kit on hand.
11870-Series
Fuse Size
4 7
2 4
2