Philips 75BDL3552T User Manual page 48

65BDL3552T/75BDL3552T/86BDL3552T
• {Secondary} - Designate this display as the secondary
display. This display can not be operated by the remote
control, and will only receive the control signal from the
primary display via RS232C connection.
• {Lock All} / {Lock all but Volume} / {Lock all but Power}/
{Lock all except PWR & VOL} - Lock the remote control
function of this display. To unlock, press and hold the
[Info] button on the remote control for more than 6
seconds. It will exit from OSD menu automatically after
locking IR.
No warning message will be shown when IR control is
locked.
Keyboard control
Choose to enable or disable the display keyboard (control
buttons) function.
• {Unlock} - Enable the keyboard function.
• {Lock All} / {Lock all but Volume} / {Lock all but Power}/
{Lock all except PWR & VOL} - Disable the keyboard
function depending on the option you selected.
NOTE: "Keyboard Control Lock Mode" This function
completely disables the access to all Keyboard
Control functions. To enable or disable the
keyboard control lock, press both [VOL+] and [UP]
buttons and hold down continuously for more than
3 (three) seconds.
Off Timer
Set automatic power off time (in hours).
Schedule
1. Default start time and end time are 00:00.
2. Start time and End time must be from the same date of
the schedule.
Schedule
Schedule list
Enable
Start time
End time
Input
Playlist
Days of the week
Every week
Back
■ Set lifecycle.
- Back:
■ Exit without saving changes.
Save:
-
■ Save schedule data.
1
SAVE
HDMI with One Wire
CEC control.
• {Off} - Disable CEC.(Default)
• {On} - Enable CEC.
The following features are supported:
• One Touch Play allows devices to switch the display to
use it as the active source when playback starts.
• System Standby enables users to switch multiple devices
to standby mode with the press of one button (HDMI
with One Wire Power off is On).
Auto signal detection
This function allows the system to detect and display the
available signal sources automatically.
Conditions for Auto Signal Detection:
1. Sub mode is "Off"
2. After showing Logo
3. Power state is not Power Off
The options are:
{Off}, {All}, {Failover}
{Off}: Disable Auto signal detection
{All}: OPS -> HDMI1 -> HDMI2 -> HDMI3 -> HDMI4 ->
DisplayPort -> DVI-D ->USB-TypeC -> VGA -> Media Player
-> SmartCMS -> Home
{Failover}:
- Failover 1: OPS(default)
- Failover 2: OPS(default)
- Faliover 3: OPS(default)
Failover 4: OPS(default)
-
- Failover 5: OPS(default)
- Failover 6: OPS(default)
- Failover 7: OPS(default)
- Failover 8: OPS(default)
Failover 9: OPS(default)
-
- Failover 10: OPS(default)
- Failover 11: OPS(default)
- Failover 12: OPS(default)
The Failover behavior is when signal lost, the display will go
to the next available source which is defined in priority list
in order.
Please note, the followings will suspend failover, and the
failover will resume when signal lost again.
- Boot On Source : When the display power on, it will go
to the source defined in this OSD option.
- Scheduler: When the display power on by scheduler,
it will go to the corresponding source according to the
current time.
- User operation: No matter what current source it is,
when user manually change source, the failover will
suspend.
To make sure failover starting from the 1
after power on, please set the 1
source too.
36
st
priority source
st
priority source as boot on