BTC 9089 ARF III Quick Installation Manual

Important Informatio
For Windows 2000 operating system, please go to
- ®
"KeyMaestro Input Device Driver" to have the Multimedia Player functions.
For Windows® XP and Windows Vista® operating systems, you could use the keyboard immediately after plugging the
-
keyboard connector into the PC. If you want to enjoy the full functionality of the keyboard, please visit our website at
http://www.emprex.com/
installed, these hot keys are reprogrammable. They can be configured as a string, a combination key, a web site, an
existing file, or a function that the driver pre-defines for you.

Hardware Installation

1. Make sure the batteries of the keyboard and mouse are installed correctly. Please
follow the polarity signs in the battery compartment.
2. Please make sure the slide switch on the back of the mouse is switched to "on"
before using the mouse. When not in use, please turn the power switch to "off" for
power saving.
3. Plug the receiver directly into your available USB port on PC.
4. Please hold the keyboard and mouse close to the receiver within 30 cm and press
any key to pair ID, and then you can use the wireless kit immediately.

Change the cursor pointer speed

You can modify the mouse pointer speed settings in the control panel.
1. Open the Start Menu by clicking "Start" at the lower-left corner on the screen
2. Then click on Settings / Control Panel / Mouse
3. In the Mouse Properties window that appears, click the Motion tab
4. Move the slide bar toward either the faster end or the slower end
5. Click OK to exit and make the change effective

Pairing Procedure

Please follow the hardware installation procedure mentioned above to install the
wireless kit, and then you can use the wireless kit immediately. If it can't work, please
follow the steps below to process ID setting of the wireless kit.
1. Press the ID pairing/connect button on the top of the receiver at least 2 seconds
until the receiver LED flashes. The receiver LED will flash 60 seconds to wait for
keyboard and mouse pairing information. (If you release the button within 2
seconds, the ID pairing will fail.)
2. Next, hold the keyboard and press the ID pairing/connect button on the bottom
of the keyboard at least 2 seconds until the LED indicator on the upper right of the
keyboard flashes once. (If you release the button within 2 seconds, the ID pairing
will fail.)
3. Then, press the ID pairing/connect button on the top of the receiver as step 1.
4. Finally, hold the mouse and press the ID pairing/connect button on the bottom of
the mouse at least 2 seconds until the LED indicator flashes once. (If you release
the button within 2 seconds, the ID pairing will fail.)
Note:
When doing the pairing procedure, please hold the keyboard or mouse close to
-
the dongle receiver within 30 cm.
Each procedure should be completed within 60 seconds.
-
Make sure your PC is on and running when doing the pairing procedure.
-
You don't have to pair ID again after changing batteries.
-
Both the keyboard and mouse can operate freely up to a radius of about 10m
-
from the receiver.
Keyboard battery life is up to 15 months and mouse battery life is up to 6 months. It
-
depends on the intensity of usage.

System Requirements

Available USB port
CD-ROM drive (for CD and Video operation)
Standard sound card (for CD and Video operation)
Microsoft® Internet Explorer 5.0 or later version (for the Internet keys)
Microsoft® Windows® 2000, Windows® XP or Windows Vista® operating system
The system supports ACPI or APM II (for power management buttons)
ATX mother board and ATX power supply (for power management buttons)

Driver Installation

USB Device Driver

The USB device driver is included with your Windows operating system.
During the initial installation of the keyboard USB device, the system will automatically detect that a new hardware device
has been added and will bring up the "Add New Hardware Wizard" dialogue box. Follow the Wizard's USB driver installation
steps. Once this installation step is completed, the basic functions of the USB device will work under the operating system. The
additional functions are provided only after the KeyMaestro driver is installed.

KeyMaestro Input Device Driver

1. After you download the driver, please find the "SetupKey.exe" in the directory and double-click this file.
2. Follow the on-screen instructions to install the driver.
3. The driver icon will show at the bottom right of the Windows system tray when the driver is loaded.
Wireless Keyboard/Quick Installation Guide
EMPREX,BTC / 9089 ARF III / 6309 ARF III
to download and install the "KeyMaestro Input Device Driver." Once the driver has been
http://www.emprex.com/ website to download and install the
Front view of
receiver
Pairing/connect button on top
of the receiver (With a LED
indicator under the pairing/
connect button)
Pairing/connect button on the
bottom of the keyboard
Power Switch
ID pairing button /
connect button
Pairing/ connect button on the
bottom of the mouse
Back view of
receiver
English