Table of Contents
Advertisement
Mega GO Par64
The ADJ LED RC infrared remote (sold seperately) has many differnet
functions and gives you complete control of your Mega GO Par64.
To control the your desired fixture you must aim the controller at the
front of the fixture and be no more the 30 feet away. To use the ADJ
LED RC you must first activate the fixtures infrared receiver, to acti-
vate the receiver please see the instructions on page 13.
BLACKOUT - Pressing this button will blackout the fixture.
AUTO RUN - This button will run an automatic program. You can
control the speed of the Auto Run by pressing the SPEED button first
and then pressing the "+" and "-" buttons.
SELECT PROGRAM - This button will let you switch between color
macro mode, color change, or color fade programs.
• If the Red LED's glow and then shut off, you are in Color Macro
Mode.
• If the Green LED's glow and then shut off, you are in Color Fade
Mode.
• If the Blue LED's glow and then shut off, you are in Color Change
Mode.
FLASH - This button will activate the strobe effect. You can control
the flash rate by pressing the "+" and "-" buttons. Press this button
again to exit strobe mode. This mode works with Static Color Mode
and RGB mode.
SPEED - Press this button and use the "+" & "-" buttons to adjust the
speed of the Auto run, Color Fade, & Color Change. This button will
also control the sound sensitivity adjustment in Sound Active Mode.
DMX MODE - This button will let you select which DMX mode you
want to use. Some fixtures will come with different DMX channel
modes. This button will switch between the different modes. Please
see pages 18-22 for DMX modes, values, and traits.
SOUND ACTIVE - This button activates sound active mode. Press
the Speed Button and use the "+" & "-" buttons to adjust the sound
sensitivity.
SLAVE - This designates the fixture as a slave fixture in a master/
American DJ
- www.Americandj.com - Mega GO Par64 User Manual Page 15
©
®
ADJ LED RC Operation
Mega GO Par64
slave configuration.
SET ADDRESS - Press this button to set the DMX address. Press
this button first, then press the numbers to set the address.
Example: Set DMX Address 1 Press "S-0-0-1"
Set DMX Address 245 Press "S-2-4-5"
R G B - Press either one of these buttons and the press the "+" or
"-" to adjust the brightness. You can also use the number buttons to
input your desired intensity.
"+" and "-" - Use these buttons to adjust the flash rate, speed of the
Auto Run, Color Change, Color Fade, sound sensitivity, and RGB in-
tensity.
DMX Control:
Operating through an DMX controller gives the user the freedom to
create their own programs tailored to their own individual needs.
Follow the directions below to set your DMX Mode and address.
1. Before connecting to an DMX controller, your fixture has different
DMX channel modes, please select your desired mode by press-
ing the DMX Mode button, then using the "+" or "-" buttons to
scroll through the DMX Channel Modes. Set the mode before you
address the fixture. See the bottom of this page for the DMX
modes.
2. After you have selected your mode, set the DMX address for the
fixture by pressing the "S" button. When the "S" button is pressed
the LED's will flash 2-3 times and all the red LED's will light. Use
the number buttons to press in your desired address. See "SET
ADDRESS" for examples.
Note: When seeting the DMX address each time a number is pressed
a LED color will glow, when you have set the DMX address correctly
all LED's will flash 2-3 times.
3. Now you may connect the fixture via the XLR connections to any
standard DMX controller. Please see pages 18-22 to for a detailed
descriptions of the DMX modes, values, and traits.
• If the Red LED's glow you are in DMX Mode 1: 1 DMX Channel.
• If the Green LED's glow you are in DMX Mode 2: 2 DMX
American DJ
- www.Americandj.com - Mega GO Par64 User Manual Page 16
©
®
ADJ LED RC Operation
Advertisement
Table of Contents
