Hide thumbs Also See for XDT13:


Quick Links

Cordless Impact Driver
IMPORTANT: Read Before Using.


Table of Contents

Summary of Contents for Makita XDT13

  • Page 1 INSTRUCTION MANUAL Cordless Impact Driver XDT13 IMPORTANT: Read Before Using.
  • Page 2: Specifications

    ENGLISH (Original instructions) SPECIFICATIONS Model: XDT13 Fastening capacities Machine screw 4 mm - 8 mm (5/32" - 5/16") Standard bolt 5 mm - 16 mm (3/16" - 5/8") High tensile bolt 5 mm - 14 mm (3/16" - 9/16") No load speed (RPM)
  • Page 3 Do not overreach. Keep proper footing and Service balance at all times. This enables better control Have your power tool serviced by a qualified of the power tool in unexpected situations. repair person using only identical replacement Dress properly. Do not wear loose clothing or parts. This will ensure that the safety of the power jewellery.
  • Page 4: Functional Description

    CAUTION: Always install the battery cartridge also void the Makita warranty for the Makita tool and fully until the red indicator cannot be seen. If not, charger. it may accidentally fall out of the tool, causing injury to you or someone around you.
  • Page 5: Overheat Protection

    This tool is equipped with an electric brake. If the tool consistently fails to quickly stop after the switch trigger When the battery is operated in a manner that causes is released, have the tool serviced at a Makita service it to draw an abnormally high current, the tool automat- center. ically stops without any indication. In this situation, turn the tool off and stop the application that caused the tool to become overloaded. Then turn the tool on to restart.
  • Page 6 Lighting up the front lamp ASSEMBLY CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before carrying out any work on the tool. Installing or removing driver bit/ socket bit 12 mm 9 mm ► 1 .
  • Page 7: Installing Hook

    Proper fastening torque for standard bolt NOTE: If the driver bit is not inserted deep enough into the sleeve, the sleeve will not return to its original N•m position and the driver bit will not be secured. In this (ft•lbs) case, try re-inserting the bit according to the instruc- tions above.
  • Page 8: Maintenance

    Operating the tool at low speed will cause a reduc- workmanship or material, Makita will repair (or at our tion in the fastening torque. option, replace) without charge. This Warranty does not apply where: •...
  • Page 9 To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles. Makita Corporation 3-11-8, Sumiyoshi-cho, Anjo, Aichi 446-8502 Japan...
  • Page 10 U.S.A., Inc., reserves the right to make changes or improvements on its products without incurring an additional obligation including any obligation to make corresponding changes or improvements to ® products previously manufactured or sold. Makita reserves the right to discontinue products at any time without notice. All illustrations and photographs displayed in this catalog are the property of Makita ® ®...
  • Page 11 XDT13M/R/Z 7-16...
  • Page 12 183E34-9 HOUSING SET C10 263005-3 RUBBER PIN 6 2 PC. C20 252126-6 HEX. LOCKING NUT M4-7 2 PC. INC. 35 852K78-3 XDT13 NAME PLATE 266429-2 TAPPING SCREW 3X16 9 PC. 455053-8 F/R CHANGE LEVER 1 PC. 143975-1 SWITCH COMPLETE 619404-1...
  • Page 13 (XDT13R) BL1820B BATTERY BL1820B SET 1 PC. (XDT13M/R) 141856-3 PLASTIC CARRYING CASE COMPLETE 2 PC. (XDT13M/R) C10 162302-3 LATCH...

Table of Contents