Specifications - Sharp PN-R426 Setup Manual

nDate/time setting
• If the time has yet to be set when the monitor is first turned
on, the date/time setting screen appears. Set the date and
time.
DATE/TIME SETTING
/
01
1. Press or to select the date and time, and press
or to change the numerical values.
2. Press the ENTER button.
• Be sure to set the date and time.
• The date/time setting screen will close automatically if
no operation is performed for about 15 seconds. The
date and time can be set using DATE/TIME SETTING
from the SETUP menu when the date/time setting screen
disappears.
Model
Power requirement
Operating temperature *
Operating humidity
Power consumption
Dimensions
(excluding protrusions)
Weight
Model
Power requirement
Operating temperature *
Operating humidity
Power consumption
Dimensions
(excluding protrusions)
Weight
* When using the monitor laying flat on a surface (when the monitor is tilted more than 20 degrees upward or downward from the perpendicular
in relation to a level surface), use the monitor at a temperature between 32°F (0°C) to 86°F (30°C).
Temperature condition may change when using the monitor together with the optional equipments recommended by SHARP. In such
cases, please check the temperature condition specified by the optional equipments.
As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement
without prior notice. The performance specification figures indicated are nominal values of production units. There may be some deviations from
these values in individual units.
8
E
Turning Power On/Off (Continued)
/ : :
/ 01 / 20 17 00 : 00
OK:[ENTER] CANCEL:[RETURN]

Specifications

PN-R706
AC 100 - 240 V, 2.6 A, 50/60 Hz
32°F to 104°F (0°C to 40°C)
20% to 80% (no condensation)
230 W
inch (mm) Approx. 62-3/16 (W) x 2-9/16 (D) x 36-1/8 (H)
(1579 x 65 x 918)
lbs. (kg) Approx. 99.3 (45)
PN-R556
AC 100 - 240 V, 2.0 A,
50/60 Hz
32°F to 104°F (0°C to 40°C)
20% to 80% (no condensation)
175 W
inch (mm) Approx. 48-7/16 (W) x
2-1/4 (D) x 27-5/8 (H)
(1231 x 57 x 702)
lbs. (kg) Approx. 55.1 (25)
TIPS
• Set the date in "Day/Month/Year" order.
• Set the time on a 24-hour basis.
• The clock is maintained by the internal battery.
• If you already set the time but the date/time setting screen
appears when the power is turned on, the internal battery
may be exhausted. Please contact an authorized SHARP
servicing dealer or service center for assistance with
battery replacement.
• Estimated service life of the internal battery: About 5 years
(depending on monitor operation)
• The initial battery was inserted at the factory when the
monitor was shipped, so it may run out of power before its
expected operation life.
PN-R606
AC 100 - 240 V, 2.2 A, 50/60 Hz
190 W
Approx. 53-1/8 (W) x 2-3/8 (D) x 30-1/2 (H)
(1349 x 60 x 775)
Approx. 72.8 (33)
PN-R496
AC 100 - 240 V, 1.8 A,
50/60 Hz
155 W
Approx. 43-1/8 (W) x
2-1/4 (D) x 24-5/8 (H)
(1095 x 57 x 626)
Approx. 43 (19.5)
PN-R426
AC 100 - 240 V, 1.5 A,
50/60 Hz
135 W
Approx. 37-3/8 (W) x
2-1/4 (D) x 21-3/8 (H)
(949 x 57 x 543.5)
Approx. 34.2 (15.5)