Cooper Lighting LUMARK PR Parker Specification Sheet

D I M E N S I O N S
3 3/16"
[81mm]
7 "
[178mm]
O R D E R I N G I N F O R M AT I O N
S A M P L E N U M B E R : H P P R - 7 0 N - 2 4 0 V - X X
Lamp Type Series
HP=High PR=Parker
Pressure
Sodium
MH=Metal
Halide
Options 6
Q=Quartz Restrike DC Bayonet Base
(Quartz lamp will not come on at initial cold start)
QM=Quick Mount
LL=Lamp Included 7
TR=Tamper Resistant Screws
F1=Single Fuse (120, 277 or 347V)
F2=Double Fuse (208, 240 or 480V)
NOTES: 1 Uses S-55 (55 Volt) lamp only. 2 Not Available in 70 & 100W Metal Halide. 3 Products also available in non-US voltages and 50Hz for international markets.
Consult factory for availability and ordering information. 4 Multi-Tap ballast is 120/208/240/277V wired 277V. 5 Triple-Tap ballast is 120/277/347V wired 347V.
Add desired voltage to end of catalog number. 6 Add as suffix in the order shown. 7 Lamp is shipped separate from luminaire. Lamp is Cooper designated
product based on luminaire requirements. Specified lamps must be ordered as a separate line item. 8 Order separately. 9 Specifications and dimensions subject
to change without notice.
M O U N T I N G D I M E N S I O N S
11 5/8" sq.
[295mm]
(4) 9/32" Dia. [7mm]
Mounting Holes
Lamp Ballast
Wattage H=Normal
70=70W Power
100=100W Factor
150=150W 1 N=Normal
175=175W Power
Factor
W=HPF CWA 2
Accessories 8
TK=Trunnion Kit
VRSD=Tamper-Resistant Screwdriver
VRSB=Tamper-Resistant Bit
COOPER LIGHTING - LUMARK
D E S C R I P T I O N
The Lumark Parker combines
strength-gaining architecture
with energy-saving technology.
U.L. listed for wet locations
and CSA certified. Mount on
non-combustible surface.
8 7/16" sq.
The durable, versatile Parker is
[214mm]
perfect for use in parking bays,
entrances and stairwells, as
well as rapid transit stations
and loading docks.
Voltage 3
120V
208V
240V
277V
347V
480V
MT=Multi-Tap wired 277V 4
TT=Triple-Tap wired 347V 5
7 0 - 1 7 5 W
H i g h P r e s s u r e S o d i u m
M e t a l H a l i d e
C L E A R P R I S M AT I C
P O LY C A R B O N AT E
PA R K I N G G A R A G E
• One-piece injection-
Options &
Accessories
molded UV stabilized
(See Below)
polycarbonate lens is a
minimum of 0.130" thick.
All light-control prisms
and blondels are on the
inside surface of the lens,
reducing dirt build-up and
making cleaning easier
• Lens is held with four
stainless steel screws.
Fasteners are captive in
the lens and sealed by
means of a neoprene
O-ring
• Die-cast aluminum with
reinforcing ribs on
exposed sidewalls.
Thickened areas occur at
lens junction and at
mounting/fastening holes.
Four 1/2" NPT conduit
entries in sides and one
in back of housing.
Black polyester powder
coat is standard
• One-piece die-cut
closed-cell silicone
mounting gasket
• Copper-wound NPF
ballast standard. Ballast
is available in high power
factor with some lamps.
Consult ordering
information
• Porcelain medium-base
socket with nickel-plated
brass screwshell
• Approximate net weight:
20 lbs. (9 kgs.)
COOPER LIGHTING
®
PR
PARKER
L U M I N A I R E
551