Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Harman Martin Exterior Wash 300 Series
Summary of Contents for Harman Martin Exterior Wash 300 Series
- Page 1 Exterior Wash 300 Series User manual...
- Page 2 2015-2020 HARMAN PROFESSIONAL DENMARK ApS. All rights reserved. Features, specifications and appearance are subject to change without notice. HARMAN PROFESSIONAL DENMARK ApS and all affiliated companies disclaim liability for any injury, damage, direct or indirect loss, consequential or economic loss or any other loss occasioned by the use of, inability to use or reliance on the information contained in this document.
-
Page 3: Table Of Contents
Table of contents Safety information ....................5 Introduction ......................9 Fixture overview ....................9 Before using the product for the first time ............9 Physical installation ....................10 Fixture location ....................10 Mounting the fixture ..................10 Adjusting tilt ...................... 11 Installing a diffuser ................... -
Page 5: Safety Information
If you have any questions about how to install or operate the fixture safely, please contact Harman Professional Technical support. For technical support in N. America, please contact HProTechSupportUSA@harman.com Phone: (844) 776-4899 For technical support outside North America, please contact your national distributor. - Page 6 Read this manual before installing, powering or servicing the fixture. Follow the safety precautions and observe all warnings in this manual and printed on the fixture. The latest version of this manual is available for download from the Exterior Wash 300, 310 and 320 pages of the Martin®...
- Page 7 Protection from eye injury Do not look directly into the product’s light output. Do not look at the light output with magnifiers, telescopes, binoculars or similar optical instruments that may concentrate the light output. Ensure that persons are not looking directly into the front of the fixture when the product lights up suddenly.
- Page 8 reflex and reaction to skin discomfort) can protect them. At distances greater than 2.2 m (7.3 ft.), potential eye and skin injury hazards from the light output are normally prevented by natural aversion reflexes. Position the Exterior Wash 310 so that persons cannot be exposed to the fixture’s light output at less than 2.2 m (7.3 ft.) from the fixture and so that prolonged staring into the light output at less than 20.1 m (66 ft.) from the fixture is not expected.
-
Page 9: Introduction
Introduction This user manual covers the following Exterior Wash 300 Series lighting fixtures from Martin®: • Exterior Wash 300 with individual red, green, blue, and white LEDs optimized for long-throw applications • Exterior Wash 310 with premixed quad-color LEDs for general applications •... -
Page 10: Physical Installation
Physical installation Warning! Read ‘Safety information’ on page 5 before installing the fixture. Contact your Martin supplier for assistance if you have any questions about how to install this product safely. Fixture location Exterior Wash 300 Series fixtures are intended for outdoor use. With an IP rating of 66, they are dust tight and able to withstand powerful water jets, but they are not submersible. -
Page 11: Adjusting Tilt
give approximately 90° of pan adjustment. If additional bolts are required to mount the fixture safely, install them passing through slots C or holes B. Install washers under all nuts and bolt heads. Figure 1. Mounting yoke base dimensions Suspending from a truss In temporary installations, you can suspend the fixture from a rigging truss by means of two rigging clamps securely fastened through holes B in the yoke base (see illustration above). -
Page 12: Installing A Diffuser
Installing a diffuser Optional diffuser lenses are available from Martin to modify the beam width (see table below and ‘Accessories’ on page 35 for details). The diffuser is held in place either by the included trim ring or, if installed, by a snoot or honeycomb louver accessory. Located close to the edge of the diffuser is a marking that gives the diffuser’s nominal beam angle and indicates which side of the diffuser must face outwards (see Figure 3). -
Page 13: Installing A Honeycomb Louver
Installing a honeycomb louver Honeycomb louver accessories that reduce lateral light spill and improve visual comfort are available from Martin in two versions: one for Exterior Wash 300 and 320 fixtures, and one for Exterior Wash 310 fixtures (see ‘Accessories’ on page 35). If you install a louver over a diffuser lens, you do not need to use the trim ring shown at C in Figure 4 on page 12 because the louver will hold the diffuser securely. -
Page 14: Installing A Snoot
Installing a snoot The optional snoot for Exterior Wash 300 Series fixtures can be installed with or without a diffuser lens (see earlier in this chapter). To install a snoot: Shut down power to the fixture and allow it to cool. If required, install a diffuser lens as described earlier in this chapter. -
Page 15: Ac Power
AC power Warning! Read “Safety Information” on page 5 before attempting to install an Exterior Wash 300 Series fixture. Lock out power to the entire installation before working on cables and connections. Electrical installation must be carried out by qualified professionals only. For protection from dangerous electric shock, the fixture must be grounded (earthed). -
Page 16: Installing A Temporary Power Plug
Installing a temporary power plug It is possible to install a power plug on the power cable for temporary use (such as setting up a fixture before installation, for example) only. If you choose to do this, install a grounding type (earthed) plug with integral cable grip that is rated minimum 277 V, 6 A. -
Page 17: Control Data Link
Control data link A DMX512 data link is required in order to control the fixture via DMX (and manage fixtures via RDM, if used). Your Martin supplier will be happy to help if you need advice or assistance in planning the link. Follow these guidelines when creating a DMX data link: ●... - Page 18 DMX data link layout Connect the wires in the data cable as shown below. Do not connect the shield conductor to ground (earth) or allow it to come into contact with a connector shell, as this may cause interference. Wires Input pair (red tube) Output pair (black tube) Shield...
-
Page 19: Setup
Setup Warning! Read ‘Safety information’ on page 5 before operating the fixture. This section explains the fixture settings and utilities that the user has access to via the control panel. Settings are retained when the fixture is powered off. A full map of the control menu including default settings can be found on page 27. -
Page 20: Programming A Standalone Show
Selecting DMX mode in the Exterior Wash 300 and 310 You can set the DMX control mode in the Exterior Wash 300 and 310 using the control panel or via RDM. To set the DMX mode using the control panel: Press and hold the MENU button to access the control menu. -
Page 21: Manual Mode
Press MENU to select the next scene to modify. When done editing scenes, press MENU again to return to the PROGRAM SHOW menu. To modify scene transitions, select FADE TIME and press ENTER. Press UP or DOWN to select a fade time from 0 to 120 seconds. - Page 22 in client fixtures are synchronized with the scene change times in the host. Every time the host changes to its next pre-programmed scene, the client fixtures change to their next pre-programmed scene at the same time. Note the following: • Although scene changes in host and client fixtures all occur at the same time, scenes do not have to be identical.
- Page 23 To set the fixture’s dimmer curve: Access the control menu and select FIXTURE CONFIG. Press ENTER. Select DIMMER CURVE and press ENTER. Select the option desired from the list above and press ENTER. Effects speed You can change the speed at which the fixture changes from one effect to the next. This lets you optimize effect changes for either smoothness or speed.
-
Page 24: Setup Via Rdm
Display lock If you want to reduce the risk of unauthorized access to the control menus, you can set the fixture to require a user password before the control panel becomes operative. Password protection is disabled by default. You can enable or disable password protection as follows: Access the control menu and select FIXTURE CONFIG. -
Page 25: Maintenance
Maintenance Warning! There are no user-serviceable parts inside. Do not open the housing. Refer any service operation not described in this manual to Martin Professional or its authorized service agents. Installation, on-site service and maintenance can be provided worldwide by the Martin Professional Global Service organization and its approved agents, giving owners access to Martin’s expertise and product knowledge in a partnership that will ensure the highest level of performance throughout the product’s lifetime. -
Page 26: Software Maintenance
Software maintenance Firmware (fixture software) can be uploaded to one fixture or multiple fixtures of the same type using a Martin Companion Cable hardware interface (see ‘Related Items’ on page 35) and a Windows PC running the Martin Companion software application. To carry out a firmware upload: Download the latest version of the Martin Companion application from www.martin.com and install it on a Windows PC. -
Page 27: Dmx Protocol
DMX protocol Exterior Wash 300 and Exterior Wash 310 Exterior Wash 300 and 310 fixtures have four DMX control modes. See ‘DMX settings’ on page 19 for full details. RGBW uncalibrated mode RGBW uncalibrated mode provides individual intensity control of each color. Output is not calibrated. Fixtures are set to this mode by default. -
Page 28: Exterior Wash 320
Exterior Wash 320 The Exterior Wash 320’s DMX protocol provides individual 0 to 100% control of the warm and cold LEDs on channels 1 and 2. Channel 3 provides color temperature control from warm to cold at maximum output. When set to a level above 26, channel 3 overrides channels 1 and 2. Channel Value Function... -
Page 29: Control Menus
Control menus To access the control menus, press and hold the MENU button. If prompted, scroll to the user password and press ENTER. Press ▼ (down) and ▲ (up) buttons to navigate the menus. Press ENTER to select a menu option. For more information, see ‘Accessing and navigating the control menus’ on page 19. The factory default settings are shown in bold. - Page 30 Show Mode Behavior when no DMX control DMX State Hold Last Look signal present Black Out Fixture Config Display Lock No/Yes Password protect control menu (contd.) Lock Password Set user password 0 – 999 (123) Restore all settings to factory Factory Reset No/Yes defaults...
-
Page 31: Troubleshooting
Troubleshooting Problem Probable cause(s) Remedy Fixture is completely dead. No power to fixture. Check power source and connections. Primary fuse blown. Isolate fixture from power. Contact Martin Service for assistance. One or more fixtures responds Incorrect DMX addressing. Check number of DMX channels incorrectly to control or does required by each fixture and check not respond at all. -
Page 32: Specifications
Specifications Physical Length .......................... 283 mm (11.2 in.) Width ..........................404 mm (15.9 in.) Height ........................... 439 mm (17.3 in.) Weight ..........................19 kg (42 lbs.) Dynamic Effects All models Intensity ............................0 - 100% Exterior Wash 300 and 310 Color mixing .......................... - Page 33 Exterior Wash 300 Light source ............ 104 x single-color LEDs (26 x R, 28 x G, 22 x B, 28 x W) Beam angle options: No diffuser ............................. 7.5° Narrow diffuser ..........................11.5° Medium diffuser ..........................25° Wide diffuser ..........................41° Very wide diffuser ..........................
- Page 34 Connections Power input ..................1.8 m (5.9 ft.) open-ended cable tail Power input cable type, EU models ........H05RN-F, 300/500 V, 3 x 0.75 mm , Ø 7 mm Power input cable type, US models .......... SJOW, 300 V, 18 AWG, WL F1, Ø 8 mm Data I/O ................
- Page 35 Accessories Exterior Wash 300 Series Narrow Diffuser Kit ..............P/N 91610155 Exterior Wash 300 Series Medium Diffuser Kit ..............P/N 91610156 Exterior Wash 300 Series Wide Diffuser Kit ..............P/N 91610157 Exterior Wash 300 Series Very Wide Diffuser Kit ............. P/N 91610158 Exterior Wash 300 Series Asymmetric Diffuser Kit ............
- Page 40 www.martin.com...
Need help?
Do you have a question about the Martin Exterior Wash 300 Series and is the answer not in the manual?
Questions and answers