Table of Contents
Advertisement
Installation precautions (continued)
What to avoid to ensure that the unit will
„
„
perform stably over a prolonged period
• Using the unit for a prolonged period in a location with high
temperature and humidity levels will cause its parts to deteriorate
and shorten its service life.
• Ensure that a cooling unit or heating unit will not blow any air
directly toward the installation location.
Be absolutely sure to use the supplied brackets
„
„
and screws to install the camera.
• Do not mount the unit by employing any methods other than those
specified.
• Do not remodel the mounting bracket or mounting screws provided
with the unit.
Before installation, always disconnect the power
„
„
plug
When installing, always use the supplied components.
Do not disassemble or modify the wall mount adaptor.
Tightening up the mounting screws
„
„
• Tighten up the screws and bolts securely to the degree that is
appropriate for each of the materials used in the mounting location
and structures.
• After tightening up the screws and bolts, check that there is no
unsteadiness and that the parts have been tightened securely.
• Use the specified tools and tighten the screws firmly.
• Tighten up the screws using the specified torque driver. Do not
use electrical drivers or impact drivers.
When the unit is no longer going to be used, do
„
„
not leave it lying around, but be absolutely sure
to dispose of it properly.
For details on how to remove the unit, refer to "Removing the
camera" (→ page 16).
When installing, transferring or disposing of
„
„
the unit, be absolutely sure to hold it by its
pedestal area.
Problems may result if the camera head is held or rotated.
Do not attach a filter, hood, extender or other
„
„
parts to the unit.
Use the dedicated AC adaptor and power cable
„
„
provided with the unit.
Connect the AC adaptor and power cable to the power inlet
securely.
Installing the AC adaptor
„
„
• Do not place the adaptor directly onto a ceiling panel or other such
surface.
Extreme danger is posed when water has collected on the surface
as a result of leaking rain, for instance.
Secure the adaptor firmly to the bottom or other surface of a
reinforcing member made of channel steel where dust
and other foreign matter will not accumulate. (→ page 15)
• Secure the adaptor firmly so that there will be no chance that it will
fall off or fall down.
Secure it using a strength which can withstand the mass of the AC
adaptor.
Install the accessory AC adaptor near the main
„
„
power outlet, and position it in such a way
that its power plug can be plugged into and
unplugged from the outlet easily.
When connecting the AC adaptor to a power outlet on the ceiling or
on any other surface where dust may collect, wipe off the dust on
the power plug at periodic intervals as an antitracking measure.
Power switch
„
„
This unit does not have a power switch. When the power
is supplied, the pan, tilt, zoom and focusing operations are
performed.
Before proceeding with maintenance, be absolutely
1
*
sure to disconnect the power plug from the power outlet.
*
1
• Under factory default conditions, the unit will be in Standby
mode when power is supplied for the first time. (Status display
lamp: Lit orange)
• When the power supply is cut off while the unit is in Standby
mode, the unit will be in Standby mode the next time power is
supplied. (Status display lamp: Lit orange)
• When the power supply is cut off while the unit is in Power ON
mode, the unit will be in Power ON mode the next time power
is supplied. (Status display lamp: Lit green)
(For details, refer to "How to turn the power on and off"
(→ page 60).)
Connecting the power cable
„
„
Be absolutely sure to connect the power cable of the AC adaptor
through a circuit breaker using one of the following methods.
(1) Connect the power cable through a power control unit.
(2) Connect the power cable to a circuit breaker in a power
distribution panel with a contact distance of 3.0 mm (1/8 inches)
or more.
Use a circuit breaker which is capable of shutting off all the
poles of the main power supply with the exception of the
protective ground conductor.
(3) Install the AC adaptor near the power outlet, and connect it
through the power plug.
Grounding
„
„
Before operating the unit, check that SIGNAL GND has been
securely grounded.
If there is a possibility of noise interference
„
„
Either wire the cables so that the power cable (ceiling light cord) of
AC 100 V
(AC 220 V
) or more, and the signal cable are placed
2
3
*
*
at least 1 meter (3.3 ft) apart.
Alternatively run each cable through its own metal conduit.
(The metal conduits must be grounded.)
*
2
For AW-UE80WP, AW-UE80KP
*
3
For AW-UE80WE, AW-UE80KE, AW-UE80WED, AW-UE80KED
Radio signal interference
„
„
If the unit is positioned near a TV or radio transmitting antenna or a
strong electrical field or magnetic field (such as that generated by a
motor, transformer or power lines), its images may be distorted and/
or the images may be affected by noise.
When connecting the cables, ensure that the
„
„
connector areas will not be subject to any load.
Doing so may cause malfunctioning.
Allowing the generated heat to escape
„
„
This unit allows the heat generated inside to escape from its
surfaces.
Do not install the unit in a location where it will be surrounded by
walls or other surfaces and where heat will be trapped.
In addition, the heat is dissipated to the bottom panel which will
warm up over time: This is normal and not indicative of any trouble.
PoE++ power supplies
„
„
Use a PoE++ (IEEE 802.3bt compliant) compatible hub or power
supply device.
Network settings
„
„
The network function of this unit does not work unless an initial
account is set up (except when using the Easy IP Setup Software
(→ page 57)). A personal computer is required to set up an initial
account. (→ page 59)
<NOTE>
• Network connection with AW-RP150 or AW-RP60 requires setup
of an initial account. (→ page 59)
When an initial account is not set up, AW-RP150 or AW-RP60 can
detect but cannot control this unit.
Installation Instructions
7
Advertisement
Table of Contents
