Safety Regulations; Layout And Items Supplied - EINHELL GC-MT 3060 LD User And Maintenance Manual

Danger!
When using the equipment, a few safety pre-
cautions must be observed to avoid injuries and
damage. Please read the complete operating
instructions and safety regulations with due care.
Keep this manual in a safe place, so that the in-
formation is available at all times. If you give the
equipment to any other person, hand over these
operating instructions and safety regulations as
well. We cannot accept any liability for damage
or accidents which arise due to a failure to follow
these instructions and the safety instructions.

1. Safety regulations

The corresponding safety information can be
found in the enclosed booklet.
Danger!
Read all safety regulations and instructions.
Any errors made in following the safety regula-
tions and instructions may result in an electric
shock, fi re and/or serious injury.
Keep all safety regulations and instructions
in a safe place for future use.
Explanation of the symbols on the machine
(Fig. 11):
1 Important! Read the operating instructions.
Follow the warnings and safety instructions.
2 Important! Risk of injury from rotating parts.
Keep your hands, feet and clothing away from
these parts.
3 Always make sure that the machine is stan-
ding solidly whenever you leave it.
4 Important! Hot machine parts. Keep your dis-
tance.
5 Important! Switch off the engine before refuel-
ing.
6 Description of the clutch lever: 0 = Hoe blade
"Stop"; 1 = Hoe blade "On"

2. Layout and items supplied

2.1 Layout
1. Engine / gear unit
2. Reversing starter
3. Spark plug wrench
Assembly set for guard plate/transport wheel
(Fig. 3a/3b):
4. Guard plate
5. Transport wheel
Anl_GC_MT_3060_LD_SPK1.indb 18 Anl_GC_MT_3060_LD_SPK1.indb 18
GB
6. 4x Screw M8x20
7. 4x Spring washer Ø8
8. 4x Washer Ø8
9. 1x Screw M10x65
10. 1x Nut M10
11. 1x Spring
12. 1x Split pin, small
Assembly set for cultivator blades/depth stop
(Fig. 4a/4b):
13a.Cultivator blade, right
13b. Cultivator blade, left
14. 2x Limiting disc
15. Depth stop
16. Split pin, large
17. 4x Screw M8x35
18. 4x Washer Ø8
19. 4x Nut M8
Assembly set for steering handle / clutch le-
ver / start/stop lever (Fig. 5a/5b):
20. Steering handle holder
21. Steering handle – clutch lever
22. Steering handle – start/stop lever
23. Cross strut
24. Clutch lever
25. Safety lever
26. Start/stop lever
27. 4x Screw M8x35
28. 4x Nut M8
29. 1x Screw M8x40
30. 1x Cap nut M8
31. 4x Screw M8x30
32. 4x Washer large Ø8
33. 4x Nut M8
34. 4x Screw M8x20
35. 4x Spring washer Ø8
36. 4x Washer Ø8
37. 1x Screw M6x45
38. 1x Cap nut M6
39. 2x Cable clip
2.2 Items supplied
Please check that the article is complete as
specifi ed in the scope of delivery. If parts are
missing, please contact our service center or the
sales outlet where you made your purchase at
the latest within 5 working days after purchasing
the product and upon presentation of a valid bill
of purchase. Also, refer to the warranty table in
the service information at the end of the operating
instructions.
•
Open the packaging and take out the equip-
ment with care.
•
Remove the packaging material and any
- 18 -
10.08.2015 16:45:15 10.08.2015 16:45:15