Summary of Contents for Broadcast LYNX Technik AG O TX 5840
Page 1
LYNXTechnik ® Broadcast Television Equipment Reference Manual O TX 5840 3GBit/s Quad SDI to Fiber Optic Converter Revision 1.0 November 2012 This Manual Supports Device Revisions: O TX 5840 Firmware Revision Control System GUI Release 6.2.0 Information in this document is subject to change without notice. No part of this document may be reproduced or transmitted in any form or by any means, electronic or mechanical for any purpose, without express written permission of LYNX Technik AG.
O TX 5840 Reference Manual. Rev 1.0 Warranty LYNX Technik AG warrants that the product will be free from defects in materials and workmanship for a period of three (3) years from the date of shipment. If this product proves defective during the warranty period, LYNX Technik AG at its option will either repair the defective product without charge for parts and labor, or will provide a replacement in exchange for the defective product.
O TX 5840 Reference Manual. Rev 1.0 Regulatory information Europe Declaration of Conformity LYNX Technik AG Brunnenweg 3 D-64331 Weiterstadt Germany Declare under our sole responsibility that the product TYPE: O TX 5840 To which this declaration relates is in conformity with the following standards (environments E1-E3): EN 55103-1 /1996 EN 55103-2 /1996...
O TX 5840 Reference Manual. Rev 1.0 Getting Started Most CardModules are installed into the rack frames and system tested in the factory. If this is an upgrade part, or service exchange item then the module is supplied in a padded cardboard carton which includes the CardModule, rear connection plate and mounting screws.
The O TX 5840 is a high quality Quad 3GBit/s / HD / SD SDI to Fiber Optic converter primarily for broadcast and professional applications. The O TX 5840 provides four channels of SDI to Fiber Optic conversion with two additional SDI outputs on BNC connectors, The SDI outputs can be mapped individually to any of the SDI inputs.
O TX 5840 Reference Manual. Rev 1.0 Module Layout Unused BNC inputs and BNC outputs should be terminated with 75Ohm to avoid any RF interference Module Front Termination Panel CardModule Page 7 of 17...
O TX 5840 Reference Manual. Rev 1.0 Connections BNC Video The O TX 5840 uses standard 75 Ohm BNC connectors. We recommend the use of high quality video cable for digital video connections to reduce the risk of errors due to excessive cable attenuation.
O TX 5840 Reference Manual. Rev 1.0 Settings and Control The O TX 5840 has an integrated micro-controller, which enables the module to be configured and controlled locally via the dip-switch or from remote when using one of the optional controllers and control software. Once set, all settings are automatically saved in non-volatile internal memory.
O TX 5840 Reference Manual. Rev 1.0 Factory Preset Condition The O TX 5840 is delivered programmed and preset for the following mode of operation: Switch 1 ON Local Adjustment Enabled Switch 2 -5 ON All inputs reclocked ON Slew rate “fast” in non-reclocked mode Switch 8 If this is the required mode of operation, then no adjustments are necessary.
O TX 5840 Reference Manual. Rev 1.0 Alarm/LED Status Indicators The O TX 5840 module has integral LED indicators, which serve as alarm and status indication for the module. Function is described below. Channel Condition Indicators 4 status LEDs are provided on the front edge of the module, one for each channel (figure 3).
O TX 5840 Reference Manual. Rev 1.0 Control System GUI When using the module in a system with the optional LYNX control system, all module settings are available on an intuitive Windows GUI interface. Any settings made using the control system will override any settings made locally. All settings are stored automatically in the module’s flash RAM.
O TX 5840 Reference Manual. Rev 1.0 Main Tab This screen is the main interface and is presented first when the module is displayed in the GUI. The input detection indicates the bit rate (SD-SDI = 270MBit/s, HD-SDI = 1.5 GBit/s;...
O TX 5840 Reference Manual. Rev 1.0 Events Tab The Events Tab is where the module alarming and error notifications are configured for the module. The GUI has an integrated error log, which is a simple text log file stored in the controller PC.
O TX 5840 Reference Manual. Rev 1.0 Specifications Video Inputs (BNC) Signal Type Serial digital video SMPTE 292M, 259M-C, 424M, DVB-ASI No. of inputs Connector Impedance 75 Ohm Cable Equalization Up to 250m Belden 8281 (270MBit/s) Up to 140m Belden 1694A (1.485GBit/S) Up to 80m Belden 1694A (2.97GBit/s) Return Loss >...
Website www.lynx-technik.com E-Mail info@lynx-technik.com LYNX Technik manufactures a complete range of high quality modular products for broadcast and Professional markets, please contact your local representative or visit our web site for more product information. LYNXTechnik ® Broadcast Television Equipment Page 17 of 17...