Troubleshooting Guide; Display Symbols - Canadian Spa Winnipeg UV Spa KH-10159 Owner's Manual

TROUBLESHOOTING GUIDE

PROBLEM POSSIBLE CAUSE
CLOUDY WATER A) organic contaminants build-up
B) suspended particles
C) pH high
D) total alkalinity too high
E) poor filtration
F) high dissolved solids
Debris in water
COLOURED WATER
High concentration of oils and organic
FOAMING
contaminants being agitated by jet
High calcium level, high pH, high alkalinity
SCALE DEPOSITS
High level of organic contaminants combined chlorine.
ODOUR
Chlorine level too high
A) pH too low
EYE/SKIN IRRITATION
B) combined chlorine due to high concentration
of organic contaminants
A) high concentration of organic contaminants
NO CHLORINE/
using up sanitizers
BROMINE READING
B) test trips may be ineffective
pH LOW
• Reduced efficacy of disinfection
Low PH and low-quality
• Corrosion of metals
chlorine causes the heater
• Skin & eye irritation
element to calcify
• Unpleasant odour
Chemical Video Guides on Canadian Spa Company channel
W I N N I P E G
SOLUTION
A) shock treatment with Granular Chlorine
B) add Granular Chlorine, use SPA-BALL
C) add pH DOWN until pH level reads 7.2–7.6
D) add pH DOWN, adjust total alkalinity to 80–150 p.p.m.
E) dirty filter, replace filter
F) empty spa and refill
Use Chlorine Granules.
Squirt FOAM-FREE on foam. Use the SPA-BALL
Drain partially, add Granular Chlorine, correct pH level to
7.2–7.6 and alkalinity to 80–150 p.p.m.
Shock with Granular Chlorine
A) add pH up until level is 7.2–7.6
B) shock with Granular Chlorine, add disinfectant
A) add Granular Chlorine
B) replace at least once a year, keep cool and out
of sunlight
pH SCALE
Helps to keep your spa
pH NORMAL pH HIGH
• Reduced efficacy of disinfection
7.2 -7.6
• Skin & eye irritation
• Forms limescale deposits
Canadian Spa Company Spa Ball KA-10003
• Staining of the filter
(14)
Initial Start-up
When your spa is first activated the display will do a count sequence of M100, L232, V52, 1-3 afterwards a message will display
'RUN PUMPS PURGE AIR' on Priming Mode - now press the JET Button to make sure the pump is running and water flowing from
the jets. If there is no movement of water please visit our Service Portal: support.canadianspacompany.com submit a ticket in
our system and our global team will effectively solve your issue quickly and efficiently 24/7.
Priming Mode will run for approximately 5 minutes (Press TEMP-UP to skip Priming Mode) then the spa will begin to run Jets on
low speed and after a few minutes the heater will start when in 'R' (Ready Mode).
TEMP UP
Increase
Temperature
TEMP DOWN
Decrease
Temperature
clean and
achieve
crystal
clear
water!
A - Heat
B - Ready Mode
C - Rest Mode
D - bba TM 2 On
E - WiFi (Cloud Connection)
W I N N I P E G
1 Pump Control System (TP500)

Display Symbols

F - Light K - Auxiliary (Jets 3 or Microsilk)
G - Cleanup Cycle L - Temperature Range (High/Low)
H - Jets 1 M - Set (Programming)
I - Jets 2 N - Filter Cycle (1 or 2 or Both)
J - Blower O - AM or PM (Time)
(15)
MENU
Press for Menu
options
JETS
Activates jets
LIGHTS
On/Off/
Light modes